TCL MOVEAUDIO S108 USER MANUAL

Chapter 1. Get started

Overview

The following diagram illustrates the components of the TCL MOVEAUDIO S108:

• 1. Case LED indicator: The indicator flashes white to indicate the charge or communication status of the earbuds or the charging case.
• 2. USB Type-C™ port: Connect the charging case to a computer or a compatible USB adapter with the supplied USB Type-C cable to simultaneously charge both the earbuds and the charging case.
• 3. Earbud LED indicator: The indicator flashes white to indicate the communication status of the earbud.
• 4. Touch control area: Tap or press to operate earbuds.

Charge the battery

Earbuds

Your charging case is a charger. To charge your earbuds, place the earbuds in the case, then close the lid.

The case LED indicator flashes in solid white when charging starts. If the case LED indicator flashes in blinking white or does not flash, it indicates that you need to charge the case as soon as possible.

NOTES:

• For best results, do not insert your earbuds in the charging case if they are wet or dirty.
• The low battery prompt tone is heard via the earbuds when the battery level for the earbuds is less than 10%.

Charging case

To charge the charging case, connect the case to a computer or a compatible USB adapter with the supplied USB Type-C cable.

The case LED indicator flashes in blinking white when charging starts, and flashes in solid white when charging is complete.

NOTES:

• It takes approximately 1.5 hours to fully charge the case using the supplied USB Type-C cable. The charging time may vary depending on the battery usage conditions.
• Use only the supplied or a certified USB charging cable for charging to prevent product damage.

Replace ear tips

To get the most use and enjoyment out of your earbuds, select the most comfortable tips for your ears.

To replace an ear tip, follow these steps:

1. Pull firmly to remove the tip.
2. Choose a new tip.
3. Align the new tip with the earbud, then push until it clicks.

A diagram shows how to remove and attach ear tips of different sizes (S, M, L).

Chapter 2. Make connections

Enjoy music and hands-free calling with your earbuds by using the Bluetooth function of your device.

Connect with a Bluetooth device

Pair your Bluetooth device to use it with the earbuds for the first time. Before you make the pairing operation, make sure your earbuds and the charging case are charged sufficiently.

To pair the earbuds with your device for the first time after purchase or after resetting the earbuds, follow these steps:

1. Take out your earbuds from the charging case, and keep them next to your device. The earbud LED indicators flash in blinking white.
2. Unlock your device, and turn on the Bluetooth function on your device.
3. Select TCL MOVEAUDIO S108 from the list of available devices to complete the connection.

A diagram shows the pairing process: earbuds taken out of the case, then connecting to a phone via Bluetooth.

• When you pair the earbuds with a device for the first time after purchase or after resetting the earbuds, the earbuds will enter pairing mode automatically if taken out of the charging case.
• If pairing is not established within 5 minutes, the pairing mode will be cancelled and the earbuds will turn off.

To pair the earbuds with your device manually, you have the following options.

Option 1

1. Remove both earbuds from the charging case, and wear the earbuds.
2. Disconnect the earbuds from your paired device, and the earbuds will enter pairing mode.
3. Unlock your unpaired device, and turn on the Bluetooth function.
4. Select TCL MOVEAUDIO S108 from the list of available devices to complete the connection.

Option 2

1. Remove both earbuds from the charging case, and wear the earbuds.
2. Triple-press either earbud, and hold the third press for about 4 seconds.
3. Unlock your device, and turn on the Bluetooth function.
4. Select TCL MOVEAUDIO S108 from the list of available devices to complete the connection.

A diagram illustrates Option 2, showing triple-pressing an earbud for 4 seconds.

If pairing is not established within 5 minutes, the pairing mode will be cancelled and the earbuds will turn off.

Disconnect from a Bluetooth device

Disconnect your earbuds from the Bluetooth device using these methods:

• Put both earbuds in the charging case, and close the case.
• Turn off the Bluetooth function on your device.
• Go to the Bluetooth menu of your device, tap your earbuds from the list of paired devices, and select disconnection option.

NOTE: The disconnection procedure may vary depending on your device model.

Reconnect with your devices

After successful pairing, the earbuds will automatically connect to the last paired device if taken out of the charging case.

• The earbuds and Bluetooth device must be turned on and within connection range.
• If the earbuds cannot find and connect to the last paired device, they will enter pairing mode shortly. You can still reconnect your earbuds to the device from the Bluetooth menu of your device.

Chapter 3. Use your earbuds

Tap or press the touch control area on the earbuds to control your music, phone calls, and other useful functions without getting out your phone.

Music feature

You can perform the playback controls by tapping your earbuds.

• Double tap either earbud: Play or pause
• Triple tap left earbud: Previous song
• Triple tap right earbud: Next song

Diagrams illustrate these controls.

Call feature

Answer and control calls using your earbuds.

Phone controls

Manage calls by tapping and holding either of your earbuds.

• Double tap: Answer or end a call
• Press and hold for 2 seconds: Reject an incoming call

Diagrams illustrate these controls.

Call waiting

If you receive an incoming call while on a call, you can use either earbud to perform the following operations:

• Double tap: Answer the incoming call and place the current call on hold
• Press and hold for 2 seconds: Reject the incoming call and stay on the current call

Diagrams illustrate these controls.

Voice assist feature

Activate the voice assistant on your device by pressing and holding either earbud for 2 seconds.

This feature supports Bixby, Siri®, and Google Assistant™.

Reset the earbuds

If you have to reset your earbuds due to connection or pairing issues, follow these steps:

1. Disconnect earbuds from your Bluetooth device, then tap either earbud 4 times.
2. The earbud LED indicators flash in blinking white when the earbuds enter reset process.

A diagram shows the reset process.

After reset process, the earbuds will enter pairing mode automatically.

Important safety information

Read all safety information before using your product. Failure to follow these safety instructions could result in injury, or damage to your product or other property.

Important handling information

Handle your earbuds and the case with care. They contain sensitive electronic components, including batteries, and can be damaged if dropped, burned, punctured, crushed, disassembled, or if exposed to excessive heat or liquid.

Clean your device regularly with a dry and soft cloth. Do not use liquids or cleaning products.

NOTE: Before cleaning, remove earbuds from the case, and disconnect the USB cable from both the case and your computer or power adapter.

Hearing loss

Listening to sound at high volume may cause permanent hearing loss. Check the volume after inserting earbuds in your ears and before playing audio.

WARNING: To prevent possible hearing damage, do not listen at high volume levels for long periods.

Medical device interference

Your device contains magnets which may interfere with medical devices such as pacemakers, defibrillators, or other medical devices within the range of 15 cm (6 inches).

IF YOU ARE A USER OF ANY OF THESE MEDICAL DEVICES, PLEASE CONSULT WITH YOUR PHYSICIAN.

Choking hazard

Your device may present a choking hazard or cause other injury to small children. Keep them away from small children.

Charging

Charge the case with the supplied USB cable. Only charge with an adapter that is compliant with the applicable international and regional safety standards. Charging with other adapters could cause damage to the case or pose a risk of injury or death. It is important to keep your device and the power adapter in a well-ventilated area when charging. Don't use damaged cables or chargers.

If you use a third-party charger, the recommended output voltage/current of the adaptor is 5Vdc/1A., and the adapter shall be CE approval type.

Battery

Do not attempt to replace the device batteries yourself. You may damage the batteries, which could cause overheating and injury. The batteries in your device should be serviced only by an authorized service provider.

Batteries must be recycled or disposed of separately from household waste. Don't incinerate the batteries. Check your country's local waste regulations for the proper disposal of electronic products.

CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Operating temperature

Your device is designed to work and be stored in ambient temperatures between 0 °C and 45 °C (32 °F and 113 °F). Your device can be damaged and battery life shortened if stored or operated outside of these temperature ranges.

The suitable temperature for the product and accessories is 0°C - 45°C.

Regulatory compliance information

This section introduces regulatory information, certification, and compliance information specific to your product.

Electromagnetic fields (EMF)

This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

FCC compliance statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FC logo

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Declaration of conformity

CE logo

Hereby, TCL Communication Ltd. declares that the radio equipment type TCL TW08 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: https://www.tcl.com/global/en/service-support-mobile/eu-doc.html

UK CA logo

Hereby, TCL Communication Ltd. declares that the radio equipment type TCL TW08 is in compliance with the Radio Equipment Regulations 2017. The full text of the UK declaration of conformity is available at: https://www.tcl.com/global/en/service-support-mobile/eu-doc.html

Disposal and recycling information

At TCL, we continually strive to improve our operations and products, and minimize our impact on the environment.

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. For recycling information, please visit www.tcl.com.

Recycling symbol ♻️: This symbol on your device and/or its accessories indicates that this device should not be disposed of with household waste. When this device reaches its end of life, take it to a collection point designated by local authorities. For more detailed information about device recycling, contact your local authorities, household waste disposal centers, or retail stores.

The separate collection and recycling of your device and/or its accessories at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.

Battery symbol ?: This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We advise you to take your product to an official collection point.

Troubleshooting

If you encounter problems while using the product, refer to the troubleshooting information to help determine the problem and find possible solutions.

General problems

Connection problems

Audio problems

Trademarks

TCL and the TCL logo are trademarks of TCL Communication Ltd. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by TCL Communication Ltd. is under license. USB Type-C™ is a trademark of USB Implementers Forum. Google Assistant word mark and logo are trademarks or registered trademarks of Google Inc. Siri is a trademark or registered trademark of Apple Inc. registered in the U.S. and other countries. All other trademarks and trade names are the property of their respective owners.

© 2021 TCL Communication Ltd. All rights reserved.