Philips Iridium gen4 BGP501/502

Product Identification

Model Series: Iridium gen4

Model Numbers: BGP501/502

Certifications: CE, R&TTE, RED

Environmental Ratings: IP66, IK10

Standard Luminaire housing is IK10. All added connectors are rated IK09.

Operating Temperature: Min. -40°C, Max. 50°C

Voltage: 220V 50Hz / 240V 60Hz

Mounting Range: 4-18m

Technical Specifications

Key: SR - Sensor Ready driver; FP - Full Prog driver, LP - Lite Prog driver, BP - Basic Prog driver

Dimensions and Mounting Options

Diagram showing overall luminaire dimensions (A, B, C, D) for Mini BGP501 and Medium BGP502.

Diagrams illustrating different luminaire cover types: FLAT GLASS and BOWL PC.

Diagrams showing dimensions (E, F) for Mini BGP501 and Medium BGP502 with Flat Glass and Bowl PC covers.

Diagrams illustrating various mounting interfaces and sensor compatibility:

• Standardized SR Socket (illustrated with dimensions G)
• CityTouch OLC NEMA SR (illustrated with dimensions G)
• CityTouch OLC COM SR (illustrated with dimensions H)
• EasyAir OLC SR (illustrated with dimensions I)
• RF Antenna (illustrated with dimensions J)
• Wattstopper OLC SR / Multisensor (illustrated with dimensions K, L, M, N)
• 7-PIN NEMA Socket with cap
• 7-PIN NEMA Socket

Installation and Wiring

Diagrams illustrating installation steps for Side Entry (42/60) and Post Top (60/76) mounting versions.

Instruction for version without cable: Disconnect before servicing. (Multilingual warnings provided).

Step-by-step diagrams show opening the luminaire, accessing internal components, and reassembly.

Diagrams show cable entry and management, including securing cables with torque specifications (e.g., 2.2 Nm, 1.0 Nm).

Wiring diagrams illustrate connections for different configurations:

• Standard version with cable
• 220V/240V connections
• DALI connections (DA+, DA-)
• LS connections (L, N)
• Wiring color codes: blue (BU), brown (BN), yellow-green (GNYE), grey (GY), black (BK).

Diagrams show spigot title angle adjustment (β) with possible options (0°, 2.5°, 5°, 7.5°, 10°) for Side Entry and Post Top mounting.

Diagrams show torque specifications for mounting bolts (e.g., 5mm, 17Nm).

Diagram illustrating a 10A maximum connection.

Control Systems and Surge Protection

RF/CTC

Graphs illustrate dimming profiles for DDFx (Dynadimmer) and LS-x (Lumistep) series.

Gear Box Components:

Detailed diagrams show the internal components of the GEAR BOX IRG4 MEDIUM and GEAR BOX IRG4 MINI.

Medium Gear Box Components:

• A - MAINS CONNECTOR: NEUTRAL IN, MAINS IN, NEUTRAL OUT, MAINS OUT
• B - OUTPUT CONNECTOR: DALI +SR OUT, NTC SIGNAL, DALI -SR OUT, NTC COM, AUX 24V SR, LED-, LED+, NTC COM
• C - LED DRIVER
• D - LUNATONE DIMMING DEVICE
• E - FUSE
• F - SURGE PROTECTION DEVICES

Mini Gear Box Components:

• A - MAINS CONNECTOR: NEUTRAL IN, MAINS IN, NEUTRAL OUT, MAINS OUT, DALI-SR, MAINS RETURN (LO), GROUNDING/EQUI, LINE SWITCH IN
• B - OUTPUT CONNECTOR: DALI +SR, NTC SIGNAL, NTC COM, AUX 24V SR, LED-, LED+
• C - LED DRIVER
• D - LUNATONE DIMMING DEVICE
• E - FUSE
• F - SURGE PROTECTION DEVICES

Surge Protection:

Diagrams show surge protection levels (10 kV) for SRG10 and SDM10 control units, applicable to Metallic Conductive poles and Non-conductive poles.

*10kV for L/N – GND non-conductive connection

ServiceTag and Documentation

Installation instructions are available via ServiceTag. This can be accessed by scanning a QR code using a smartphone via the Service Tag website or application (Android device only).

Product information can also be found by scanning the Service Tag on the product label.

Safety and Compliance

General Safety Warnings:

• Disconnect power before servicing.
• Follow all instructions in the manual for safe use and to maintain warranty.
• Use calibrated torque wrenches for specified bolt tightening.
• Only qualified personnel should replace light sources, control gear, or external cables.
• Position the luminaire to avoid prolonged staring into the light source from a close distance (less than 25cm).

Zhaga-D4i and SR Compatibility:

For Zhaga-D4i/SR-Certified luminaires, only Zhaga-D4i/SR-Certified components/sensors are to be used. Functional compatibility and override possibilities require release from the master component/sensor supplier. Full system verification is required when using a NEMA 7-pin socket on an SR-based luminaire. Failure to adhere to these recommendations may cause damage and non-compliance, for which Signify assumes no responsibility.

Further information available at: https://www.zhagastandard.org/products and https://www.lighting.philips.co.uk/oem-emea/products/driving-connected-lighting.

EU Declaration of Conformity:

Signify Holding declares that the radio equipment type is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: http://www.philips.com/lighting. This declaration is available in multiple languages including ES, EN, FR, IT, DE, DA, NL, PL, HU, CS, SL, LV, LT, PT, SV.

General Disclaimer:

This document contains information relating to the product portfolio of Signify which may be subject to change. No representation or warranty as to the accuracy or completeness of the information included herein is given. The information presented is not intended as a commercial offer.

© 2021 Signify Holding. All rights reserved.