Creality Sprite Extruder Pro Kit User Manual
Version 1.1
Parts List 零件清单
- Sprite Extruder Pro (including adapter board) Sprite Extruder Pro (包括转接板)
- Mounting Backplate Kit 安装背板套件
- M3x6 Hexagon Round Head Screw *5 M3×6内六角圆柱头螺丝*5
- Copper Alloy Nozzle (0.4mm) 铜合金喷嘴(0.4mm)
- Flat Cable (1.3m) 排线(1.3m)
Installation Instructions 安装步骤
1. Remove the original hotend kit, and install mounting backplane kit on X-axis profile. 拆掉机器原有喷头后,将安装背板套件安装在X轴型材上。
2. Select a appropriate slot on the mounting backplane according to timing belt length. Adjust the eccentric nut so that mounting backplane kit slides freely on the X-axis profile without shaking. 根据同步带长度,在安装背板上选择合适的卡位,调节偏心螺母,使安装背板套件在X轴型材上不晃动且自由滑动。
3. Fix Sprite Extruder Pro on mounting backplane with 4pcs M3×6 hexagon round head screws. 将 Sprite Extruder Pro 通过 4颗 M3×6 内六角圆柱头螺丝螺丝固定在安装背板上。
Motherboard Wiring Diagram 主板接线示意图
4. Connect terminal to corresponding interface on motherboard according to the cable label(Terminals without labels are redundant and do not need to be connected to motherboard. Please disconnect printer power when wiring). Then connect the other end of the cable to Sprite Extruder Pro. 按排线线标将对应端子接在主板相应位置(无线标的端子为冗余,无需接在主板上,接线时请断开机器电源)。然后再将排线另一端连接到 Sprite Extruder Pro。
E-steps Adjustment
If the printer does not support adjusting the Esteps value to 424.9, you can make it with the following 4 steps:
- Create a new text file (txt) and type "M92 E424.9" in the text.
- Press “Enter” to continue typing "M500”.
- Save the file as the gcode format, and copy it into TF card.
- Insert the TF card into the printer and click to print this file. At this time, the printer's Esteps value has been adjusted to 424.9.
- Click "Storage Configuration".
若机器不支持将 Esteps 数值调节到 424.9, 可通过以下四步调节:
- 新建一文本文档(txt),键入“M92 E424.9";
- 回车继续键入“M500”;
- 将文件另存为 gcode 格式,拷入 TF 卡;
- 插入机器点击打印此文件,此时机器 Esteps 数值已调节为 424.9;
- 点击“存储配置”。
5. Adjust the printer's Esteps value to 424.9 (the value is for reference only and can be fine-tuned according to the actual printing situation), and then click "Store Settings". 将机器 Esteps 数值调节到 424.9(参考数值,可根据实际打印情况微调此值),然后点击“存储设置”。
1. After installation, you need to level printing platform again.
2. The side adjusting screw on the Sprite Extruder Pro can adjust the clamping degree between extrusion gear and filament. Clockwise is for tightening and anticlockwise is for loosening. 可通过调节 Sprite Extruder Pro 侧面调节螺丝,调节挤出齿轮与耗材夹紧程度,顺时针调紧,反之调松。
3. The withdrawal distance must be less than 3mm. 回抽距离需小于3mm。
Troubleshooting
If 3D printer restarts during hotend heating up, please reverse the heating tube connectors on mainboard. 若打印模型加热喷头时,3D打印机出现重启现象,将加热管主板端接头位置对调。
Sprite Extruder Pro Kit Material Guide 耗材指引
| Material 耗材 | Enclosure 保温罩 | Dry box 使用耗材干燥盒 | Retraction distance (direct drive) 回抽距离 | Retraction speed 回抽速度 | Heatbed temperature (±5°C) 热床温度 | Nozzle temperature (±5°C) 喷嘴温度 | Recommended printing speed 推荐打印速度 |
|---|---|---|---|---|---|---|---|
| CR-PLA | NO | NO | 0.8mm | 40mm/s | 60°C | 200°C | 50mm/s |
| CR-TPU | NO | NO | 2mm | 40mm/s | 60°C | 230°C | 50mm/s |
| HP-TPU | NO | NO | 2mm | 40mm/s | 60°C | 210°C | 50mm/s |
Retraction speed: 35-45 mm/s
Retraction distance (direct drive) for rigid materials (PLA): 0.8 mm
Retraction distance (direct drive) for soft materials (TPU-95): 2 mm
提示: ①安装过程中,所有线不能缠绕。 ② 更多参数和高级设置,请参考官网: www.creality.com 具体打印参数需要根据不同耗材生产商做调整。
Leveling Tip 调平指引
This paper can be used for manual leveling or auxiliary leveling. thickness 0.1mm. 本页纸可用于手动调平或备用,厚度0.1mm。
1. [Diagram showing nozzle moving across paper with an X mark]
2. [Diagram showing nozzle at 0.1mm above bed, with arrows indicating adjustment]
3D Printing Industry Evangelist
Due to the differences between models, product images and description only for reference purpose, please see the subject produce. The final explanation rights shall be reserved by ShenZhen Creality 3D Technogy Co., Ltd. 因每款机型不同,实物与图可能有所差异,请以实物为准,最终解释权归深圳市创想三维科技股份有限公司所有。
