Can-Am® X3 Elite Series Stage 7 Stereo Kit

Model: UTVS-X3-S7-E

Compatible Vehicle:

CAN-AM® X3

Included in the Kit:

Wet Sounds Compact 2-Zone Media Receiver Source Unit with SiriusXM-Ready® and NMEA 2000 Connectivity
UTV Stereo Can Am X3 Wet Sounds MC 20 Lower Mount
UTV Stereo Can Am X3 Center Console Covers
UTV Stereo Low Current Harness Only
UTV Stereo Blue Rocker Switch
UTV Stereo Rocker Switch Cover - Stereo
UTV Stereo USB/AUX Flush Mount Adapter
UTV Stereo 3.5mm to RCA Adapter Cable
UTV Stereo AM/FM Under Dash Antenna
UTV Stereo 6 Channel RCA Harness - Front, Rear, Sub + Remote Wire
UTV Stereo Subwoofer Level Controller with a Rocker Switch Housing, compatible with OEM Ride Command Sub
Harness for RZR Pro Vehicles
UTV Stereo Signature Series 6.5" Speakers (Pair)
UTV Stereo Can Am X3 6.5" Kick Panel Speaker Enclosures
UTV Stereo 6.5" RGB Speaker Rings (Pair)
UTV Stereo Signature Series 6.5" Speakers (Pair)
UTV Stereo Can Am X3 6.5" Dash Panel Speaker Mounts
UTV Stereo 6.5" RGB Speaker Rings (Pair)
UTV Stereo Elite Series Compression Horn 8" Speakers (Pair)
UTV Stereo Elite Series 8" Cage Mount Pods (Pair)
UTV Stereo 8" Cage Pod Base (Pair)
Axia Alloys 1.85" Modular Roll Cage Strap Clamp - Single Black
Axia Alloys 1.85" Modular Roll Cage Strap Clamp - Single Black
UTV Stereo 8" RGB Speaker Rings (Pair)
UTV Stereo Flex 10" Low Profile Subwoofer 1 OHM, Dual Voice Coil
UTV Stereo Can Am X3 Low Profile Sub Enclosure (Front Driver Side), compatible with all X3 models
UTV Stereo Flex 10" Low Profile Subwoofer 1 OHM, Dual Voice Coil
UTV Stereo Can Am X3 Low Profile Sub Enclosure (Front Passenger Side), compatible with all X3 models
UTV Stereo Elite Series 4 Channel Amplifier
UTV Stereo Elite Series Mono Amplifier
UTV Stereo Can Am X3 Large Upper Amplifier Mount
UTV Stereo 8AWG Amp Power Harness for Installation (86" Length - 80 Amp Fused)
UTV Stereo Amplifier to Speaker Wire & RGB Harness
UTV Stereo Bluetooth RGB Controller Kit - Includes RGB Controller & Rocker Switch Harness
UTV Stereo Amplifier to Dual Subwoofer Wire Harness
UTV Stereo Y-Adapter Harness for 6-Pin Speaker Wire & RGB
UTV Stereo Enclosure Side Harness for 6-Pin Speaker Wire & RGB

For installation assistance, contact UTV Stereo at info@utvstereo.com or 480.616.2299.

Instructions

Follow these instructions to install your UTV Stereo Stage Kit. For detailed guidance on individual components, refer to the specific install instructions and videos available at utvstereo.com.

Remove seats and disconnect the battery.
Disassemble the upper dash. Remove fenders or panels to access the amplifier mount location. (Reference Large Upper Amplifier Mount Instructions)
Remove front and rear center console panels to access power harness routing. (Reference Power Harness Instructions)
Install the amplifier mount. (Reference Large Upper Amplifier Mount Instructions)
Install amplifiers onto the amplifier mount.
Route the power harness from the bus bar to the amplifier. Ensure the fuse is removed during installation. (Reference Power Harness Instructions)
Install sub boxes and subwoofers into the vehicle, routing wires to the amplifier. (Reference Sub Box Instructions)
Install the source unit into the lower source unit mount. (Reference Lower Source Unit Mount Instructions)
Install the source unit mount into the center pocket. (Reference Lower Source Unit Mount Instructions)
Connect power wires from the source unit to the source unit harness. Connect the source unit harness to the bus bar and mount the switch. (Reference Source Unit Harness Instructions)
Connect and route the remote wire and RCA wire from the source unit to the amplifier. (Reference Wire Diagram) Connect any rear camera, reverse trigger, or USB/AUX connections at this time.
Install the RGB controller harness switch. Connect and route the RGB controller and RGB wires near the amplifier. Route bus bar wires to the bus bar. (Reference RGB Controller Kit Instructions)
Install dash panels and cage pods. (Reference Dash Panel and Cage Pod Instructions)
Connect speaker wire and RGB wire to all speakers. Install speakers into dash panels and cage pods. (Reference Dash Panel, Cage Pod, and Speaker Instructions)
Route speaker wires to the amplifier or RGB controller and make connections. (Reference Wire Diagram and RGB Controller Wire Diagram)
Install the fuse into the power harness and reconnect the battery.
Power on and tune the amplifier. (Reference Page 4 & 5)
Install center console covers. (Reference Center Console Cover Instructions)

Wiring Diagram

The wiring diagram illustrates the connections between the head unit, amplifiers, speakers, subwoofer, and RGB controller for the Can-Am X3 Elite Series Stage 7 Stereo Kit. It details the routing of power, signal, and speaker wires, including connections to the OEM bus bar and specific speaker locations like front left dash, front left kick panel, rear left, front right kick panel, and front right dash speakers.

Key components shown in the diagram include:

Head Unit
2 x Elite Series Amplifiers (4 Channel and Mono)
6-Channel RCA Harness
Subwoofers (Dual 10" Low Profile)
Speakers (Signature Series 6.5", Compression Horn 8", Cage Mount Pods 8")
RGB Controller
OEM Bus Bar

Specific wire color coding is indicated for certain connections, such as green and green/black for the front left dash speaker, and purple and purple/black for the front right dash speaker.

Tuning Your System

This section provides guidance on setting amplifier adjustments for optimal performance.

Elite Series UTVS-E1000.4D Amplifier Tuning:

The tuning blueprint provides a visual guide for setting the amplifier controls. Users are instructed to cut out the provided image, align it with the amplifier tuning panel, and make adjustments accordingly. Key settings include HPF, LPF, CLIP, SENS, and FREQ for both front and rear channels.

Front/Rear Channel Settings (Example):

HPF: Set according to speaker requirements.
LPF: Set according to speaker requirements.
SENS (Sensitivity): Adjust for optimal signal input.
FREQ: Typically set between 40Hz - 400Hz.
CLIP: Monitor for clipping to prevent distortion.
POWER PROTECT: Indicates amplifier protection status.

Elite Series UTVS-E1200.1D Amplifier Tuning:

Similar to the 4-channel amplifier, the UTVS-E1200.1D tuning blueprint guides users through setting controls for optimal subwoofer performance. Key settings include LPF, SENS, BOOST, PHASE, SUBSONIC, and CLIP.

Subwoofer Channel Settings (Example):

LPF: Typically set between 50Hz - 250Hz.
SENS (Sensitivity): Adjust for optimal signal input.
BOOST: Adjust bass boost level (0dB - 18dB).
PHASE: Adjust between 0° and 180° for best bass integration.
SUBSONIC: Typically set between 10Hz - 55Hz to filter out ultra-low frequencies.
CLIP: Monitor for clipping to prevent distortion.
POWER PROTECT: Indicates amplifier protection status.

	Can-Am X3 Elite Series Stage 8 Stereo Kit Installation Guide Comprehensive guide for installing the Can-Am X3 Elite Series Stage 8 Stereo Kit, including a detailed parts list and step-by-step instructions for wiring and tuning.
	Polaris RZR Pro Series Elite Series Stage 7 Stereo Kit Installation Guide Comprehensive guide for installing the UTV Stereo Elite Series Stage 7 Stereo Kit (UTVS-PRO-S7-E) in Polaris RZR Pro Series vehicles. Includes a list of included components, step-by-step installation instructions, and amplifier tuning guidelines.
	UTV Stereo Product Catalog: High-Performance Audio for Off-Road Vehicles Explore the comprehensive UTV Stereo product catalog featuring high-performance speakers, amplifiers, subwoofers, media receivers, batteries, and lighting designed for UTVs. Enhance your off-road audio experience with durable, weather-resistant components.
	Polaris Xpedition Sub Enclosure Kit Installation Guide Step-by-step instructions for installing the UTV Stereo Sub Enclosure Kit for the Polaris Xpedition, including parts list and recommended products.
	Polaris RZR Pro Series Ride Command Stage 7 Stereo Kit Installation Guide Comprehensive installation guide for the Polaris RZR Pro Series Ride Command Stage 7 Stereo Kit (UTVS-PRO-S7-RC), including component lists, wiring diagrams, and tuning instructions.
	UTV Stereo Flex Series 10" Low-Profile Subwoofer Installation Manual Detailed installation instructions, specifications, and wiring diagrams for the UTV Stereo Flex Series 10" Low-Profile Subwoofer (Models UTVS-F10LP1, UTVS-F10LP2).
	UTV Stereo 6.5" LED RGB Speaker Rings Installation Guide This guide provides installation instructions for UTV Stereo's 6.5" LED RGB Speaker Rings (Part #: UTVS-65LSR). It details the parts included, recommended products, and wiring options for both Bluetooth controller and hardwire setups.
	UTV Stereo 8" LED RGB Speaker Rings Installation Guide This guide provides information on the UTV Stereo 8" LED RGB Speaker Rings (Part #: UTVS-8LSR), including parts list, compatibility, and installation options.