CAN-AM® X3 ELITE SERIES STAGE 8 STEREO KIT

INCLUDED IN THE KIT

• Wet Sounds Compact 2-Zone Media Receiver Source Unit with SiriusXM-Ready® and NMEA 2000 Connectivity
• UTV Stereo Can Am X3 Wet Sounds MC 20 Lower Mount
• UTV Stereo Can Am X3 Center Console Covers
• UTV Stereo Low Current Harness Only
• UTV Stereo Blue Rocker Switch
• UTV Stereo Rocker Switch Cover - Stereo
• UTV Stereo USB/AUX Flush Mount Adapter
• UTV Stereo 3.5mm to RCA Adapter Cable
• UTV Stereo AM/FM Under Dash Antenna
• UTV Stereo 6 Channel RCA Harness - Front, Rear, Sub + Remote Wire
• UTV Stereo Subwoofer Level Controller with a Rocker Switch Housing
• UTV Stereo Signature Series 6.5" Speakers (Pair)
• UTV Stereo X3 6.5" Dash Panel Speaker Mounts
• UTV Stereo 6.5" RGB Speaker Rings (Pair)
• UTV Stereo Can Am X3 6.5" Kick Panel Speaker Enclosures
• UTV Stereo Elite Series Compression Horn 8" Speakers (Pair)
• UTV Stereo Elite Series 8" Cage Mount Pods (Pair)
• UTV Stereo 8" Cage Pod Base (Pair)
• Axia Alloys 1.85" Modular Roll Cage Strap Clamp - Single Black
• Axia Alloys 1.85" Modular Roll Cage Strap Clamp - Single Black
• UTV Stereo 8" RGB Speaker Rings (Pair)
• UTV Stereo Flex 10" Low Profile Subwoofer 1 OHM, Dual Voice Coil
• UTV Stereo Can Am X3 Low Profile Sub Enclosure (Front Driver Side) Compatible with all X3 models
• UTV Stereo Can Am X3 Low Profile Sub Enclosure (Front Passenger Side) Compatible with all X3 models
• UTV Stereo Elite Series 4 Channel Amplifier
• UTV Stereo Can Am X3 Large Upper Amplifier Mount
• UTV Stereo 8AWG Amp Power Harness for Installation - 86" Length - 80 Amp Fused
• UTV Stereo Elite Series Mono Amplifier
• UTV Stereo X3 Lower Amplifier Mount
• UTV Stereo Bluetooth RGB Controller Kit - Includes RGB Controller & Rocker Switch Harness
• UTV Stereo Amplifier to Speaker Wire & RGB Harness
• UTV Stereo Amplifier to Dual Subwoofer Wire Harness
• UTV Stereo Add On Amplifier to Speaker Wire & RGB Harness for 4 Channel Front and Bridged Rear Channels
• UTV Stereo Enclosure Side Harness for 6-Pin Speaker Wire & RGB

For installation and tuning assistance, contact UTV Stereo at info@utvstereo.com or 480.616.2299.

INSTRUCTIONS

Follow these instructions to install your UTV Stereo Stage Kit.

Each individual part has its own specific install instructions and/or install video that can be found on that particular item's page at utvstereo.com. Use this resource to install each part individually.

1. Remove seats and disconnect the battery.
2. Disassemble upper dash. Remove any fenders or panels to expose where the amplifier mount will be mounted. (Reference Large Upper Amplifier Mount Instructions)
3. Remove both front and rear center console panels to expose where power harnesses will be routed. (Reference Power Harness Instructions)
4. Install amplifier mount. (Reference Large Upper Amplifier Mount Instructions)
5. Install amplifiers onto amplifier mount.
6. Route power harness from the bus bar up to the amplifier. REMOVE FUSE DURING INSTALL. (Reference Power Harness Instructions)
7. Install sub boxes and sub woofers into the vehicle and route wires to the amplifier. (Reference Sub Box Instructions)
8. Install source unit into lower source unit mount. (Reference Lower Source Unit Mount Instructions)
9. Install source unit mount into center pocket. (Reference Lower Source Unit Mount Instructions)
10. Connect power wires from the source unit to the source unit harness. Connect source unit harness to bus bar and mount the switch. (Reference Source Unit Harness Instructions)
11. Connect and route remote wire and RCA wire from source unit to amplifier. (Reference Wire Diagram) (If you have a rear camera, reverse trigger, or USB/AUX connect them during this step)
12. Install RGB controller harness switch. Connect and route RGB wires and RGB controller near the amplifier. Route bus bar wires to bus bar. (Reference RGB Controller Kit Instructions)
13. Install dash panels, kick panels, and rear compression horn speakers. (Reference Dash Panel, Kick Panel, and Compression Horn Instructions)
14. Connect speaker wire and RGB wire to all speakers. Install speakers into dash panels and kick panels. (Reference Dash Panel, Kick Panel, Compression Horn, and Speaker Instructions)
15. Route wires from speakers to amplifier or RGB controller and make connections. (Reference Wire Diagram and RGB Controller Wire Diagram)
16. Install fuse into power harness and reconnect the battery.
17. Power on and tune amplifier. (Reference "Tuning Your System" on page 4 & 5)
18. Install center console covers. (Reference Center Console Cover Instructions)

WIRING DIAGRAM

This section provides a visual representation of the wiring for the CAN-AM X3 Elite Series Stage 8 Wiring Diagram (UTVS-X3-58-E).

Front Left Dash Speaker: Use WHITE & WHITE/BLK wire.

Front Left Kick Panel Speaker: Use GREEN & GREEN/BLK wire.

Rear Left Compression Horn: Use GREEN and GREEN/BLK wire.

Front Right Kick Panel Speaker: Use PURPLE & PURPLE/BLK wire.

Front Right Dash Speaker: Use PURPLE & PURPLE/BLK wire.

Rear Right Compression Horn: Use GRAY & GRAY/BLK wire.

The diagram illustrates connections between the Head Unit, RGB LED Controller, Amplifiers (6-Channel and Mono), Subwoofers (Dual 10" and Dual 12"), Speakers, and the OEM Buss Bar.

Key components shown include:

• 6-Channel RCA Harness
• Amplifiers (UTV Stereo Elite Series)
• Subwoofer connections (Coil 1+, Coil 1-, Coil 2+, Coil 2-)
• Head Unit connections (ANTENNA, +12V CONSTANT, ACCESSORIES, GROUND)
• RGB LED Controller
• OEM Buss Bar in Center Console

TUNING YOUR SYSTEM

This section provides guidance on setting adjustments for optimal performance of your amplifier(s).

ELITE SERIES UTVS-E1000.4D Amplifier Tuning

PRE-TUNE 'STARTING POINT' Settings:

• FRONT/REAR HPF: MIN MAX
• FRONT/REAR LPF: MIN MAX
• FRONT/REAR SENS: MIN MAX
• FRONT/REAR FREQ: 40 - 400
• CH Mode: 4CH / 2CH

Tuning Blueprint:

1. Cut out the image along the red outline.
2. Align the cutout image with the amplifier tuning panel.
3. Make your adjustments.

ELITE SERIES UTVS-E1200.1D Amplifier Tuning

PRE-TUNE 'STARTING POINT' Settings:

• LPF: 50Hz 250Hz
• SENS: MIN MAX
• PHASE: 0° 180°
• BOOST: 0dB 18dB
• SUBSONIC: 10Hz 55Hz
• CLIP: (Indicator light)
• POWER PROTECT: (Indicator light)

Tuning Blueprint:

1. Cut out the image along the red outline.
2. Align the cutout image with the amplifier tuning panel.
3. Make your adjustments.