AGPTEK 2-in-1 LED Christmas Projector Light

General Introduction

Thank you for choosing this product. Please read this user manual carefully before use and keep this instruction for future reference.

1. Ocean Wave + Pattern Light Projector: Equipped with two projection heads, one for RGBW water wave ripple effect and another for patterns image projection. Features latest varied different colorful pattern slides with varied different color ocean wave effect for Halloween and Christmas.
2. 100% Water Resistant for Outdoor: The projector light is rainproof for outdoor use. It has a 16.4ft long power cable with a weather-resistant cap, long enough to connect with power and work great even if rain or snow.
3. Effective Remote Controllability: Includes a remote controller to choose lights color, timer setting, or flashing choice. Remote range up to 40ft.
4. Way of Installation: Includes a ground stake for outdoor use by sticking into the ground, as well as a flat base for indoor activities. Find the place you want, then plug it into the ground, place on flat surfaces, or secure it into a wall by screws. Use the remote controller to change the color and pattern or set a timer for working.

Important Tips

1. This product is not a toy. Please keep away from children under 3 years old.
2. This product contains small parts which may cause choking hazard if detached.
3. Please DO NOT allow children to play with the ground stake since the end point of the stake is sharp.
4. Keep it away from fire and open flames.
5. Place the light projector 16.4 to 26.3ft from the projection surface for better results of brightness and visibility (in a dark environment).

FAQs

Q: Timing failure.

A: 1. Check whether there is any electromagnetic interference in the surrounding area. 2. Check whether the controller is working properly. 3. Check whether the timing is not set, then reset once: press the timing button once and the projector lamp flashes twice, which means opening timing; Press it again and the projector lamp flashes three times, which means turning off timing.

Q: Too low brightness and visibility.

A: The projection effect is affected by the surrounding light source. Please keep the projection lamp used in a dark environment. The darker the environment, the brighter the projection effect.

Q: The shapes are too vague.

A: The projector effect is affected by the delivery distance, so do not place it too close or too far (Recommended distance is 5-8 meters).

Q: Why is it not the previously set pattern after restarting?

A: Directly disconnecting the adapter will make the product restore the factory settings, so do not turn off the projector by disconnecting the power. It is recommended to turn off the product by the remote control.

Package Contents

• 1*Light Projector
• 1*Remote Control
• 1*Power Adapter
• 1*Ground Stake
• 1*Base
• 4*Screws
• 1*Instruction

Specifications

• Power Input: 100-240V, AC50/60Hz, 1000mA (Only use with supplied transformer)
• Total Power: 7W
• Ocean Wave LED Lights: 4 solid colors (Red, Green, Blue, White), 9 mixing colors
• 2 Patterns Styles: Halloween, Christmas
• Working Temperature: 5°F -113°F (-15℃~45℃)
• Power Supply Waterproof Grade: IP44
• Product Waterproof Grade: IP65
• Power Cord: 16.4ft
• Application: Outdoor/Indoor Decoration

Remote Control Instructions

The remote control has the following buttons:

• ON/OFF: Powers the device on or off.
• WP + / WP -: Adjusts the water wave patterns.
• SAD + / SAD -: Adjusts the single shapes.
• WP STRT/DC: Starts or stops the water patterns.
• WP CIRC: Circulates the water patterns.
• SAD STRT/DC: Starts or stops the single shapes.
• 4H, 6H, 8H: Timer functions for 4, 6, or 8 hours respectively.

Set Timing Function: Press the timing button once and the projector lamp flashes twice, which means enabling timing. Press it again and the projector lamp flashes three times, which means turning off timing.

Memory Function: After turning off, it will light up again to return to the mode before turning off. (Restores factory settings after power off)

Manufacturer Information

Manufacturer: Shenzhen ShiYu Photoelectric Technology Co., Ltd.

Address: 2/F, NO.2 Building, Shengxuan Industrial Zone, Shilong Avenue No.9, Shiyan Street, Baoan District, Shenzhen.

E-mail: support@agptek.com.