VIHALS Gateleg Table Assembly

This document provides step-by-step instructions for assembling the IKEA VIHALS Gateleg table. Please ensure you have all parts and tools before beginning.

General Assembly Tips

• Assemble on a soft surface, like a rug, to prevent scratching the table parts. ?️
• Ensure all parts are correctly aligned before tightening screws. ✔️
• Do not overtighten screws, as this can damage the material. ❌
• If you encounter difficulties, refer to the IKEA website or contact IKEA customer support. ?

Parts Overview

The assembly requires various hardware components and wooden parts. Key hardware items include:

• Screws (various sizes, e.g., 155677, 105107, 115461, 100356, 101076)
• Dowels (e.g., 10067513, 10129219)
• Hinges
• Feet/Wheels (e.g., 102428, 10058897)
• Other small components (e.g., 100181, 100372, 109049, 10081692, 10081198, 130423)

The main wooden components form the table structure, including the tabletop, legs, and support beams.

Assembly Steps

Step 1: Prepare Components

Identify all parts and hardware. A screwdriver ? is required for assembly. The diagram shows two people holding wooden panels, with a close-up of a screw and a screwdriver.

Step 2: Initial Part Alignment

Begin by aligning the first set of wooden components. The diagram shows two people correctly aligning parts, followed by an illustration of two people with crossed arms ❌, indicating incorrect alignment or assembly.

Step 3: Surface Protection

Assemble the initial frame components on a soft surface, such as a rug, to protect the finish. The diagram shows assembly on a rug, contrasted with an image showing potential damage ❌ to a surface if assembled on a hard floor without protection.

Step 4: Following Instructions

Review the assembly steps. The diagram shows a person looking at instructions with a question mark ❓, then proceeding with assembly. This step emphasizes understanding the process before proceeding.

Step 5: Assembling Frame Base

Begin constructing the base frame of the table. The diagram shows wooden beams and panels being joined together on a flat surface.

Step 6: Attaching Support Beams

Attach the horizontal support beams to the vertical leg components. The diagram shows screws being inserted to connect these parts.

Step 7: Connecting Frame Sections

Continue assembling the main frame structure. The diagram illustrates connecting different wooden sections using screws.

Step 8: Securing Frame Components

Ensure all frame components are securely fastened. The diagram shows screws being tightened into pre-drilled holes.

Step 9: Adding Internal Supports

Install the internal shelving or support structure within the main frame. The diagram shows these parts being slotted into place and secured.

Step 10: Attaching Feet/Wheels

Attach the feet or wheels to the bottom of the table legs. The diagram shows a close-up of a screw (10067513) and a foot component (105107) being attached, with an indication of correct attachment ✔️ and incorrect attachment ❌.

Step 11: Assembling Side Frames

Assemble the two U-shaped side frame structures. This involves attaching hinges to the wooden pieces using screws (e.g., 100356, 10058897) and dowels (e.g., 101076).

Step 12: Completing Side Frames

Finish assembling the U-shaped side frames by attaching the feet/wheels. The diagram shows screws (e.g., 101076) and feet (e.g., 10058897) being attached to the frame ends.

Step 13: Attaching Frame to Tabletop

Connect the assembled side frames to the main tabletop. Hinges are used, secured with screws (e.g., 101076). The diagram shows the tabletop with pre-drilled holes and the side frames being attached via hinges.

Step 14: Securing Hinges

Fasten the hinges securely to the tabletop and frame. The diagram shows four screws (102428) being used to attach a hinge plate to the tabletop.

Step 15: Intermediate Frame Assembly

The diagram shows the main frame structure now attached to the tabletop, with the internal supports in place.

Step 16: Folding Mechanism

The diagram shows the action of folding or unfolding parts of the table structure, indicated by curved arrows ↪️ ⤴️. This likely relates to the gateleg mechanism.

Step 17: Folding the Table

Two people are shown carefully folding the table. The diagram depicts the action of bringing the sides together.

Step 18: Attaching Tabletop Leaves

Attach the extendable leaves to the main tabletop. A warning symbol ⚠️ is shown, indicating a pinch point hazard when closing or opening the table. Two screws (2x) are shown being inserted.

Step 19: Final Assembly

The table is now in its final configuration, with the leaves extended. The diagram shows the completed gateleg table. Screws are being inserted to secure the final components.