Jewenwils Outdoor Digital Yard Stake Timer

Important Safety Information

Please pay attention to the warning signs. Read these instructions with caution before operating the device and keep them properly for future reference.

Warning: To reduce the risk of fire, electric shock, or personal injury, strictly follow these instructions:

• Do not connect any devices which may exceed the maximum ratings of this timer.
• Do not immerse in water.
• Children are not allowed to use the timer without supervision.
• Do not disassemble or repair the product; only authorized service personnel should perform repairs.
• Always unplug and store indoors when not in use.
• Used batteries should be disposed of safely and environmentally.

Installation

The outdoor digital yard stake timer consists of three main sections: the timer unit, the middle stake section, and the pointed ground stake. To install, connect these three sections together. Ensure the stake is firmly tightened to the body of the timer before inserting it into the ground.

Tip: If the ground is too hard to insert the stake, it is recommended to dig a hole that matches the stake's dimensions using a hard object.

Button Layout and Components

The timer unit features several key components:

1. Light Sensor: Detects ambient light density to automatically turn connected devices on or off.
2. Operating Mode Indicator: Displays the current operating mode.
3. Select Button: Used to choose and switch between operating modes.
4. Overload Protection Switch: Manually turns power on/off and provides overload protection.
5. Outlets: Receptacles for plugging in lights or other devices to be controlled by the timer.
6. Transmitter: The remote control unit used to operate the timer wirelessly.

The remote control unit typically includes buttons for ON, OFF, 2Hr, 4Hr, 6Hr, 8Hr, and Timer functions.

Operating Instructions

To begin, press the overload protection switch to the "I" (ON) position to turn on all outlets. The indicator on the switch will illuminate.

The yard stake timer can be operated either via the included transmitter (up to 100ft away) or by manually pressing the button on the stake to select the desired function. The following modes are available:

• ON: Power is continuously supplied to attached devices. The power indicator will be lit.
• Dusk - Dawn (represented by a sun/moon symbol): Power turns on at dusk and remains on until dawn.
• Dusk + 2H/4H/6H/8H: Power turns on at dusk and automatically turns off after the selected duration (2, 4, 6, or 8 hours).
• Timer + 2H/4H/6H/8H: Power turns on immediately and automatically turns off after the selected duration (2, 4, 6, or 8 hours).
• OFF: Power is turned off to attached devices. The "power" indicator will extinguish.

Control by Receiver (Timer Unit)

1. Press the timer control button (3) to turn on all outlets to "On-Always On" mode. The power indicator (2) will light up.
2. Press the timer control button (3) to select "Sensor" (dusk-to-dawn) mode. The indicator (2) will light up, and all outlets will be ON when sensing dusk and OFF at dawn.
3. Press the timer control button (3) to select "Sensor plus 2hr, 4hr, 6hr or 8hr" mode. The indicators (2) for the Sensor and the specific hour selected will light up. All outlets will turn on when sensing dusk and then turn off after the selected duration.
4. Press the timer control button (3) to select "Timer 8hr, 6hr, 4hr or 2hr" mode. The indicators (2) for the Timer and the specific hour selected will light up. All outlets will turn on immediately and then turn off after the selected duration. The current setting will repeat daily.

Control by Transmitter (Remote)

1. Press the ON or OFF button on the transmitter to turn the receiver power ON or OFF.
2. Press the Timer button plus 2Hr, 4Hr, 6Hr or 8Hr on the transmitter to turn on the receiver and then off after that specific hour you selected. This power cycle will repeat ON daily.
3. Press the Sensor button (dusk-to-dawn) on the transmitter. The receiver will be ON when sensing dusk and OFF at dawn.
4. Press the Sensor button plus 2Hr, 4Hr, 6Hr or 8Hr on the transmitter to turn on the receiver after sensing dusk and then off after the specific hour you selected.

Notes

• The receiver must be located within 100 feet from the remote transmitter. Actual functional range may be affected by factors such as weather, radio frequency interference, low remote battery, and obstructions between the transmitter and receiver.
• The timer repeats its setting daily. In case of a power failure, the timer will revert to the off state and will need to be reset to the desired operating mode once power is restored.
• Once programming activates at the sensor with the 2H, 4H, 6H, or 8H Mode, the program cycle will complete before the timer resets. External lighting sources like headlights, porch lights, or street lamps will not interfere with the active timer program.
• In Sensor Mode, temporary light sources (e.g., headlights, porch lights) will not interfere with the photocell function unless they are on for more than 15 minutes. In such a case, the timer will shut off until darkness is restored.
• When set to "ON", the timer provides continuous power to attached devices until it is switched to "OFF" or any other operating mode.

Overload Protection

The unit features a reset function for overload protection. If the power unexpectedly turns off, unplug all connected devices, press the power switch (which resets the device), and then reconnect the devices.

Battery Handling and Usage

• Install the battery observing the positive (+) side up as indicated inside the battery compartment.
• Never throw batteries into a fire. Do not expose batteries to fire or other heat sources.
• Batteries contain mercury. Do not dispose of them in trash. Recycle or manage them as hazardous waste.

Battery Replacement (Remote Control)

To replace the battery in the remote control:

1. Remove the battery compartment cover from the remote.
2. Remove the old battery.
3. Place a new Type 3V (CR2032) lithium battery into the battery compartment.
4. Ensure the battery is installed correctly with the positive (+) side up. The battery compartment typically shows a diagram indicating the correct polarity for the CR2032 3V battery.

⚠ WARNING: Chemical Burn Hazard

The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you suspect batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

• Replace the battery compartment cover securely.
• Dispose of or recycle spent/discharged batteries in compliance with all applicable laws. For detailed information, contact your local solid waste authority.

Caution: Failure to properly align the battery polarity can cause personal injury and/or property damage.

Specifications

• Frequency: 433MHz
• Transmitter Power Input: 3V Lithium Battery (CR2032)
• Receiver Power Input: AC 125V Electrical Outlet
• Receiver Power Output: 13 Amps / 125 Volts / 1625W
• Cord: 6ft SJTW 16/3C
• Receiver Model: SP-058A
• Transmitter Model: TR-034-8
• FCC ID: PAGTR-033-8

General Safety Information

WARNING: Disregarding cautions may cause damage, fire, or fatal shock. When using outdoor electrical products, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury.

CAUTION:

• Risk of Fire: Not for permanent installation. Use only with outdoor equipment, Christmas-tree, or other seasonal decorative-lighting products having a total of 13 Ampere maximum. Do not install or use this product for more than a 90-day period.
• If using Christmas tree or decorative-lighting products not marked with an ampere rating, connect no more than 140 screw-base lamps (C7 or C9) or 12 strings with midget (push-in) lamps to this cord set.
• Cord sets must be plugged into a GFCI-protected receptacle.
• If using an outdoor-use cord set for an extended period (greater than 90 days), consider hard wiring a permanent outdoor-use receptacle rated for year-round use in the area where power is needed. Contact a licensed electrician for proper installation of permanent wiring.
• After installation, the connector must be maintained a minimum of 6 inches above ground.
• SUITABLE FOR INDOOR/OUTDOOR USE – STORE INDOORS WHILE NOT IN USE.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

One Year Limited Warranty

Jewenwils provides a One Year Warranty for materials and workmanship from the purchase date, supported by their professional R&D and QC teams. The warranty does not cover damage caused by personal misuse or improper installation.

For customer service, it is recommended to attach the Order ID and Name when seeking assistance.

The product is UL Certified.