Moen Two-Handle Widespread Lavatory Faucet Installation Guide

Contact Moen First

For installation help, missing, or replacement parts:

• USA: 1-800-BUY-MOEN (1-800-289-6636) | www.moen.com
• Canada: 1-800-465-6130 | www.moen.ca
• Mexico: 011 52 (800) 718-4345 | www.moen.com.mx

Product Information

Two-Handle Widespread Lavatory Faucet

LLAVE DE LAVABO DE DOS MANIJAS

ROBINET DE LAVABO À DEUX POIGNÉES ÉLOIGNÉES

Helpful Tools

For safety and ease of faucet replacement, Moen recommends the use of these helpful tools:

• Safety Glasses: Gafas de seguridad / Lunettes de sécurité
• Adjustable Wrench: Llave ajustable / Clé ajustable
• Phillips Screwdriver: Destornillador Phillips / Tournevis Phillips
• Sealant: Sellador / Mastic
• Thread Seal Tape: Cinta para sellar roscas / Ruban pour joints filetés

Image is for reference only (Style varies by model).

Record Purchased Model Number: _______________________

(Save instruction sheet for future reference)

Register Online: www.moen.com/product-registration

Parts List

Important Installation Notes

• Spout installs through a 1-1/8" min. dia. hole. Valves install through a 1-1/8" min. dia. hole.
• Maximum hole diameter: 1-1/2".
• For deck thickness 1-1/2" to 3", use service kit #175709.

Caution: Always turn water supply OFF before removing existing faucet or disassembling the valve. Open faucet handle to relieve water pressure.

Icon Legend: ? Warning / ⬆️ Above sink / ⬇️ Below sink

Installation Steps

1. Step 1: Apply a bead of sealant to the base of the Spout Base (C) as shown, then turn upright.
2. Step 2: Place the Spout Assembly (A) into the Spout Base (C) in the center opening of the sink.
3. Step 3: Install the Mounting Bracket (K) and Mounting Plate (L) onto the shank of the Spout Assembly (A). For sink decks less than 1" thick, finger-tighten the bracket and plate with the Mounting Nut (M). For sink decks greater than 1" thick, only the Mounting Plate (L) is needed.
4. Step 4: Attach the Mounting Tool (I) to the Mounting Bracket Nut (M) as shown. Hand tighten the nut.
5. Step 5: Insert a screwdriver into the hole of the Mounting Tool (I). Further tighten the Mounting Bracket Nut (M).
6. Step 6: Note: The Upper Mounting Washer (D) has "UP" for correct installation orientation.
7. Step 7: Apply sealant into the underside groove of the Upper Mounting Washers (D) (x2). Flip them over to install onto the sink deck, right side up with "UP" visible.
8. Step 8: Insert the hot and cold Valve Bodies (G) and (H) through the Mounting Washers (D) as illustrated.
9. Step 9: Partially install screws into the Mounting Ring (F).
10. Step 10: Slide the Mounting Washer (E) and Mounting Ring with screws (F) onto the hot Valve Body (G). Thread the Mounting Ring (F) and hand tighten.
11. Step 11: Finish tightening with a screwdriver. Repeat steps 10 and 11 for the cold Valve Body (H).
12. Step 12: Remove protective sleeves from Valve Bodies (G) and (H).
13. Step 13: Attach the Quick Connect Hose (J) to the bottom of the spout assembly shank. Push the hose up as far as possible until a "click" is heard. Tug downward to test engagement. If necessary, press the button to disengage the hose.
14. Step 14: Install the ends of the Quick Connect Hose (J) onto each valve body for correct installation orientation, as shown with the arrow facing up. Push hose ends up until a "click" is heard. Tug downward to test engagement.
15. Step 15: Turn the stems of Valve Bodies (G) and (H) to the closed position.
16. Step 16: Install faucet Handles (B) onto Valve Bodies (G) and (H).
17. Step 17: Position Handles (B) pointing in the off direction. Holding one handle stationary, thread the base of the handle assembly onto the valve bodies clockwise until tightened to the deck.

Drain Installation

For Type A Waste Install: follow steps 18 - 20.

For Type B Waste Install: follow steps 21 - 29.

Drain Type A Installation

18. Step 18: Clean the drain opening in the bottom of the sink. Place the Drain Body (P) with Gasket (Q) into the sink opening.
19. Step 19: Install the Cone Gasket (R) onto the Drain Body (P). Tighten with the Drain Mounting Nut (S).
20. Step 20: Install the Push-Down Drain Plug (O) into the Drain Body (P). Press down to activate the pop-up mechanism. Proceed to Step 30.

Drain Type B Installation

21. Step 21: Clean the drain opening in the bottom of the sink.
22. Step 22: Apply a generous amount of sealant to the underside of the Waste Seat (V). Insert the Waste Seat (V) through the sink drain opening.
23. Step 23: Ensure the Drain Flange (W), Drain Gasket (X), and Drain Hex Nut (Y) are installed in order on the Waste Seat (V). Assemble the Tailpiece (Z) to the Waste Seat (V). Tighten by hand. Ensure the pivot rod opening on the Tailpiece (Z) points toward the faucet and wall.
24. Step 24: Install the Lift Rod (T) through the faucet into the Lift Rod Strap (CC). Hand tighten the nut of the strap.
25. Step 25: Make the final tightening of the Drain Hex Nut (Y) to the Tailpiece (Z) with a wrench. Insert the Waste Plug (U) into the sink opening.
26. Step 27: Install the Pivot Rod (AA). It can be installed in two ways: next to the hole in the Waste Plug (U) for cleaning access, or inserted into the hole to prevent removal. Tighten the Pivot Rod Nut (BB).
27. Step 28: Push the Pivot Rod (AA) down. Place the clip over the closest hole on the Lift Rod Strap (CC), then squeeze the Pivot Rod Clip (DD). Slide the Pivot Rod (AA) through the clip and strap holes.
28. Step 29: Loosen the nut on the Lift Rod Strap (CC) to allow the Lift Rod (T) to rest in the faucet. Verify the Pivot Rod (AA) is pushed down and the Waste Plug (U) is open. Tighten the nut with a wrench.

Connecting Supply Lines

30. Step 30: Attach flexible supply lines (not included) to the valve bodies as shown. Tighten with a wrench.
31. Step 31: Connect the other ends of the supply lines to the stops.
32. Step 32: Tighten the flexible supply lines to the stops with a wrench.

Final Steps and Aerator Flushing

33. Step 33: Turn water on. Installation is complete.

Flushing for Threaded Aerator (Steps A-D)

1. Step A: Unthread the Aerator (N) from the spout and remove it. Set the aerator aside for re-installation.
2. Step B: Turn handles on and run water for 15 seconds to flush any debris.
3. Step C: Turn handles off.
4. Step D: Re-install the Aerator (N) to the spout. Hand tighten until secure.

Flushing for Cache Aerator (Steps E-H)

1. Step E: Attach the Aerator Tool (EE) to the aerator from the spout and remove it. Set the aerator aside for re-installation.
2. Step F: Turn handles on and run water for 15 seconds to flush any debris.
3. Step G: Turn handles off.
4. Step H: Using the Aerator Tool (EE), re-install the aerator to the spout. Finger tighten until secure.

Warranty Information

Moen Limited Lifetime Warranty

Moen warrants to the original consumer purchaser that this product will be leak- and drip-free during normal use and that all parts and finishes will be free from defects in material and workmanship for as long as the original owner owns their home. For other purchasers, the warranty period is 5 years from the original date of purchase.

If a defect occurs during the warranty period, Moen will provide necessary parts free of charge and replace any defective part or finish. This warranty excludes labor charges, damage from installation/repair, and indirect or consequential damages.

This warranty gives you specific legal rights, and you may have other rights that vary by state or province.

For warranty claims, contact Moen with proof of purchase and details of the defect.

Moen Incorporated, 25300 Al Moen Drive, North Olmsted, Ohio 44070-8022, USA.

Moen de Mexico, S.A. de C.V., Carretera Saltillo-Monterrey KM 14.7, Ramos Arizpe, Coahuila, Mexico 25900.

Moen Inc., 2816 Bristol Circle, Oakville, Ontario L6H 5S7, Canada.