Aosu Solar-Powered Security Camera System

What's Included

SolarCam Max/Pro

• ? SolarCam Max/Pro x2
• ? USB-C Charging Cable x2
• ? Mounting Bracket x2
• ? Mounting Base x2
• ? Mounting Screws and Anchors x2
• ? Quick Start Guide
• ? HomeBase
• ? Power Adapter for HomeBase
• ? Ethernet Cable

Solar Panel x2

• ☀️ Solar Panel
• ? Universal Joint
• ⚙️ Socket nut
• ? Locking Screw Cap
• ? Base
• ? Mounting Screws and Anchors

Product Overview

SolarCam Max/Pro

A diagram shows the SolarCam Max/Pro with the following labels:

• Status LED
• Lens
• Spotlight
• Microphone
• Motion sensor
• SYNC button
• Speaker
• USB-C port

HomeBase

A diagram shows the HomeBase with the following labels:

• USB port
• Ethernet port
• SYNC button
• Power port
• Status LED
• Speaker

Connecting the Homebase

Connect the HomeBase to the Internet

1. Power on the HomeBase, then use the ethernet cable provided to connect the HomeBase to your home router.
2. The LED indicator turns green (this may take up to 1 min) when HomeBase is ready for setup.

Setting Up the System

Download the App and Set up the System

Download the Aosu App from the App Store (iOS devices) or Google Play (Android devices).

Sign up for an Aosu App account, then follow the onscreen instructions to complete the setup.

A diagram shows a smartphone with the Aosu app open, and the HomeBase and a camera.

Mounting the SolarCam Max/Pro

Find a Good Mounting Spot

To find a spot to mount SolarCam Max/Pro, you need to test wireless signal strength.

1. Open the Aosu App, go to Camera Settings > Mounting Guide.
2. To test the wireless signal strength, take your camera and phone to the location where you want to mount the camera.
3. Move the camera as close to the Wi-Fi Router as possible to get a better signal.

A screenshot of the Aosu app shows a "Test Signal" screen indicating "Great Wi-Fi Signal Strength" and "The current location is good to mount the camera.".

Select Height and Location

Hang SolarCam Max/Pro SE 7-10 ft (2-3 m) above the ground. This height maximizes the detection range of the motion sensor of SolarCam Max/Pro. Avoid placing SolarCam Max/Pro under direct sunlight.

A diagram illustrates the recommended mounting height and detection zone. The camera is mounted 7-10 ft (2-3 m) above the ground, with a motion detection zone extending up to 30 ft (10 m).

Mount the Camera

1. Drill holes with a 15/64 inch (5.95mm) drill bit, then insert the anchors into the holes. Anchors are necessary for walls made of hard materials like concrete, brick, or stucco. Firmly attach the mounting base onto the wall.
2. Tighten the camera to the mounting bracket.
3. Accurately snap the camera to the mounting base.
4. Adjust the viewing angle by checking the live stream feed in the Aosu App.

Installation Instruction of Solar Panel

Place the Solar Panel in an area with consistent sunlight throughout the year. It only needs a few hours of direct sunlight each day to keep your camera powered. The amount of energy produced by the solar panel is affected by weather conditions, seasonal changes, geographic location, etc.

1. Fix the base to your mounting location using the included screws. If the installation surface is soft or unstable, first use a ∅6.0 drill bit to drill a hole in the wall, then insert the anchor nail into the hole, and fix the base with screws.
2. First, install the locking screw cap into the universal joint and then screw the circular socket nut into the universal joint.
3. Screw the universal joint into the back of the solar panel. Tighten it firmly with the attached nut.
4. Screw the locking screw cap into the base. Make sure that the universal joint is angled upward.
5. When adjusting the solar panel left or right, loosen the locking screw cap, turn the sleeve rod, and tighten the locking screw cap when the panel is in position.
6. Solar panel's angle can be adjusted up and down up to 90°.

Tip: After the installation is complete, please check that all locking mechanisms are tightly secured.

1. Keep the installation angle of solar panels about 30-45° with the horizontal plane, as shown in the picture below.
2. The installation between the solar panel and the camera is shown in the following figure. Open the silicone cover at the bottom of the camera, insert the power cord through the opening, and plug it into the USB-C Charging Port. Then, close the cover, taking up any slack in the power cord from the solar panel.

A diagram shows three mounting scenarios for the camera and solar panel, with checkmarks for correct installations and crosses for incorrect ones.

Charging the Camera

LED indication:

• Charging: Green light flashing
• Fully charged: Steady green

Charging time: 7 hours

A diagram shows the camera being charged via a USB-C cable connected to a 5V/2A power source.

SolarCam Max/Pro comes with a built-in battery. Before setup, fully charge your SolarCam using the provided USB-C Charging cable.

Notice

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure Statement

The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm.

Declaration of Conformity

This product complies with the radio interference requirements of the European Community.

Hereby, Glazero Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Web site: https://www.aosulife.com/.

This product can be used across EU member states.

Do not use the Device in environments with extreme temperatures (too high or too low), and never expose the Device to strong sunshine or excessively wet environments.

The suitable temperature for HomeBase and accessories is -10°C to 45°C. The suitable temperature for Video Doorbell and accessories is -20°C to 40°C.

When charging, place the device in an environment with normal room temperature and good ventilation. It is recommended to charge the device in an environment with a temperature ranging from 5°C to 25°C.

RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirements, use the product maintaining a 20cm distance between the device and human body.

For HomeBase: Wi-Fi Operating Frequency Range: 2412~2472MHz; Wifi Max Output Power: 17.13dBm(EIRP). Wi-Fi Operating Frequency Range: 5150MHz ~ 5850MHz, Wifi Max Output Power: 13.7dBm(EIRP).

For Video Doorbell: Wi-Fi Operating Frequency Range: 2412~2472MHz; Wi-Fi Max Output Power: 18.30 dBm.

This product is designed and manufactured with high quality materials and components, which can be recycled and reused.

This symbol ♻️ means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

⚠️ Battery Warning

• Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types).
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

Customer Service

Warranty

12-month limited warranty (The actual warranty period shall be implemented according to the requirements of local laws and regulations).

Email Us

Customer Support: support@aosulife.com

Call Us

• United States: +1-866-905-9950 Mon-Fri 9AM-5PM
• United Kingdom: +44-20-3885-0830 Mon-Fri 9AM-5PM (GMT)
• Germany: +49-32-221094692 Mon-Fri 9:00-17:00
• Japan: +81-50-5840-2601 Mon-Fri 9AM-5PM (JST)

f Facebook: @aosulife

? Twitter: @aosulife

▶️ YouTube: @aosulife