ALL LED Smart Remote RGBW Installation Guide
Model: AiQ/RGBW/RMT
Dimensions
Length: 137mm
Width: 46mm
Thickness: 13mm
Returns & Faulty Items
For any issues encountered during or after installation, please contact the ALL LED technical department. Items should not be returned directly to the outlet without prior testing and confirmation of a manufacturing defect. Statutory rights are not affected.
The manufacturer is not liable for damages caused by faults, misuse, or incorrect installation. Refer to the troubleshooting guide for further information. Goods are supplied under ALL LED LTD terms and conditions, available upon written request.
Product Overview & Features
Remote Features:
- RGB Colour Changing Mode: Click to play built-in modes, hold to adjust speed.
- Scene Saving/Recalling: Press and hold S1-S7 to save colours; click to recall saved colours.
- Brightness Control: Press and hold to increase or decrease light intensity.
- Warm White Control: Click to turn ON/OFF warm white; press and hold to adjust intensity (0-100%).
- Cool White Control: Click to turn ON/OFF cool white; press and hold to adjust intensity (0-100%).
- ON/OFF Button: General power control.
- Preset Scenes: Click to recall 6 preset scenes sequentially.
- Group Control: Supports 4 groups, with up to 30 lighting devices per group.
- Compatibility: Controls DIM, CCT, RGB, RGBW, and RGB+CCT lighting devices.
- LED Indicator: Provides status feedback.
Product Data
| Code | Protocol | Operation Voltage | Battery Type | Transmission Frequency | Transmission Range (Free Field) | Dimension | Protection Grade |
|---|---|---|---|---|---|---|---|
| AiQ/RGB/RMT | Zigbee 3.0 | 6V | CR2032 x 2 | 2.4 GHz | 30 m | 137x45x13mm | IP20 |
Quick Install Guide
1) Connecting Your Remote to Smart Home Hub
Note: Remove protective film from battery before first use.
- From Smart Home Hub App or Voice Control, add a device or enter pairing mode (30 seconds).
- Press and hold the power button until the LED indicator turns on.
- Quickly short press the WW button. The LED indicator will flash. Pairing is successful when the LED indicator blinks x3 quickly (20 seconds timeout).
2) Connecting Your Remote To Intelligent Lighting
- Set the receiving device to Find and Bind mode. Lights will flash indicating mode is active (3 minutes duration).
- Bring the remote within 10cm of the Intelligent Lighting Device (3 minutes timeout).
- Press and hold a group button. The LED indicator will flash quickly and then blink x6 to indicate successful pairing.
Factory Reset Remote
Remove the remote from a previous Smart Home Hub if connected, to avoid pairing failure.
- Press and hold the power button until the LED indicator turns on.
- Quickly short press the Power Button five times. The LED indicator blinks x3 quickly to indicate a successful reset.
Note: If unsuccessful, reset the remote and try again.
Removing Intelligent Lighting From Your Remote
- Set the receiving device to Find and Bind mode. Lights will flash indicating mode is active (3 minutes duration).
- Press and hold the power button until the LED indicator turns on.
- Quickly short press the CCT button twice. The LED indicator will flash. Unpairing is successful when the LED indicator blinks x6 (20 seconds timeout).
How To Save And Recall Scenes
Saving Scenes
- Ensure lighting devices are paired to the desired groups (1-4).
- Select the groups for scene creation. Red indicators under group buttons will illuminate.
- Press and hold a scene button (S1-S7) to save the current lighting settings.
Recalling Scenes
- Short press scene buttons S1-S7 to recall a saved scene for the selected group(s).
Environmental Protection
Dispose of electrical products responsibly according to local recycling facilities. Check with your Local Authority or retailer for recycling advice.
Safety Information
ISOLATE MAINS SUPPLY BEFORE HANDLING ANY ELECTRICAL PRODUCTS.
Manufacturer Information
ALL LED LTD
42 Sedgwick Road, Luton, LU4 9DT
Website: www.allledgroup.com
Email: sales@allledgroup.com
Tel: +44 (0)208 841 9000
