Ingenico

1. Product Introduction

1.1 What's in the Box

Procedures:

• Open the package
• Check the following items (subject to actual product configuration):
  • Base host
  • Product instruction
  • USB Type-C cable
  • 5V 2A Power adapter
• Inspect the terminal and accessories and remove any shipping tape or packaging items.

1.2 Device Layout

Diagram illustrating the Ingenico AXIUM DX8000-BASE-C device layout. Callout 1 indicates the USB-TYPE C Power Interface. Callout 2 indicates the DX8000 Charging Contact.

2. Product Specifications

2.1 Product Functions

The base is designed to charge DX8000 terminals. With an optional mount, the base can be used to fix the DX8000 to a counter or other structure.

2.2 Product Technology Specifications

2.3 Environmental Conditions

Environmental conditions for running, storing, and delivering the product:

3. Product Installation Instructions

3.1 Installing the DX8000 and Base

Installation procedures:

• Remove all packaging and tape used for shipping purposes.
• Place the base onto the location where it will be used.
• Connect the power adapter to the back of the base and plug it into an appropriate power plug.
• Set the DX8000 terminal on top of the base.
• Observe the charging indicator to ensure that the base is properly connected and working.

Diagram showing the Ingenico AXIUM DX8000 terminal being placed onto its base.

3.2 Fixing of the base

To fix the base and the DX8000 to a table, an optional mounting kit can be used. Installation procedures:

• Mount the space block on the table with screws.
• Fasten the Base structure on the space block with three screws.
• Place the base on the structure to lock it.
• Fasten the Base Fixing structure on the base with three screws.
• Replace the battery cover of DX8000 and place DX8000 on the base to lock it.

If removal of the base and DX8000 is required, use a screwdriver to push the area of the structure to unfix them.

Diagram illustrating the process of fixing the Ingenico AXIUM DX8000 base to a surface using screws and a mounting block. It also shows how to attach the base to the structure and then place the DX8000 terminal onto the base.

4. Standards and Operating Information

Prevent the terminal from sun exposure, high temperature, moisture, and other adverse conditions. Cut off the power before cleaning the device and wipe the main body with a dry cloth.

When the following abnormal phenomena occur, stop running the device immediately, cut off the power supply, and report to the service provider as soon as possible:

• Harsh noise heard during operation.
• Impurities or water found in the machine.
• Unpleasant smell found during operation.

4.1 Delivery and Storage

Deliver the device normally, avoiding rain, snow, sun exposure, and mechanical impact. The product should be stored in its original box. The box should be at least 15cm away from the floor, at least 50cm from the wall, heat source, cold source, window, or air inlet.

4.2 Power Adapter

The base can only be connected to the adapter provided with the DX8000. Other power adapters may damage the base or DX unit.

WARNING

The power adapter provided is specially designed for Ingenico DX8000-BASE-C. Do not use any other power supply. The use of a power supply with apparently similar voltage/current characteristics may damage your terminal.

RF exposure

Under normal use conditions, the product's antenna should be kept at least 20cm away from the user's body. A warning statement regarding the 20cm separation distance and prohibition of operating near a person is printed on the user manual. This product, under normal use, is located in the electromagnetic far field relative to the human body.

4.3 Standards

CE Marking

The CE marking indicates that the DX8000-BASE-C complies with the requirements of European Directive 2014/53/EU on Radio equipment for the protection of health and safety of the user and any other person. It also complies with protection requirements for electromagnetic compatibility and harmonized standards.

Environment (WEEE, Batteries and packaging)

This product is labeled in accordance with European Directives 2012/19/EU concerning Waste Electrical and Electronic Equipment (WEEE) and 2013/56/EC concerning Batteries and Accumulators. These provisions require producers and manufacturers to be liable for the take-back, treatment, and recycling of equipment and batteries at the end of their life.

THE PRODUCT

The [crossed-out waste bin symbol] on the product or its accessories indicates that the product belongs to the family of electrical and electronic equipment, and waste batteries must not be thrown away but collected separately for recycling.

Please contact your retailers for more detailed information about the compliance solution for disposing of your old product and used batteries.

Packaging waste must also be collected separately to ensure proper disposal and recycling. This allows participation in the re-use and upgrading of Electrical and Electronic Equipment Waste, which can benefit the environment and human health.

The [DC Voltage symbol] indicates DC Voltage.

This Document is Copyright © 2022 by Ingenico Group. Ingenico retains full copyright ownership, rights, and protection in all material contained in this document. The recipient can receive this document on the condition that they will keep it confidential and will not use its contents in any form or by any means, except as agreed beforehand, without prior written permission from Ingenico. Furthermore, no one is authorized to place this document at the disposal of any third party without Ingenico's prior written permission. If such permission is granted, it will be subject to the condition that the recipient ensures that any other recipient of this document, or information contained therein, is held responsible to Ingenico for the confidentiality of that information.

Care has been taken to ensure that the content of this document is as accurate as possible. Ingenico, however, declines any responsibility for inaccurate, incomplete, or outdated information. The contents of this document may change from time to time without prior notice, and do not create, specify, modify, or replace any new or prior contractual obligations agreed upon in writing between Ingenico and the user.

Ingenico is not responsible for any use of this device that would be inconsistent with this document.

All trademarks used in this document remain the property of their rightful owners.

www.ingenico.com
13-17 rue Pagès, 92150 Suresnes – France
Banks and Acquirers International Holding, SAS / 814 767 216 RCS Nanterre