BIGBIG WON ARMOR-X User Manual

Name of Each Part

The ARMOR-X features the following components:

• USB-C flexible cable
• LED1, LED2
• Turbo button
• Profile switch button
• Hair trigger button
• M1, M2, M3, M4 Back buttons
• Mapping button
• FN button
• Power on/off button
• USB-C port
• Pair button
• Indicator
• USB wireless adapter

Package Contents: BIGBIG WON ARMOR-X Wireless Back Button/USB Wireless Adapter, TYPE-C Data Cable/User Manual/Qualified Certification.

Supported Controller: Xbox Series Controller

Supported Platform: Xbox Series X | S / Xbox One / Switch / Win 10/11

Attach the ARMORX

1. Remove the battery compartment cover off the Controller and attach the ARMORX to the battery compartment.
2. Plug the USB-C flexible cable of ARMORX into the USB port of the Xbox Series Controller.

Notice: For best performance, fully charge the ARMORX before first use. Charging takes approximately 2.5 hours.

Connect to the Console

The Xbox Series controller with ARMORX supports Xbox/PC/Switch. Hold the power button to turn on the ARMORX and plug the USB wireless adapter into the console's USB port. The ARMORX will detect the platform automatically.

• LED1 slowly flashes: ARMORX is connecting with the adapter. Fast flashes indicate pairing. LED1 becomes solid when connection is successful (adapter indicator will be the same).
• LED1 and adapter indicator solid: Connection successful and switched to the corresponding platform color.
• LED2 flashes: Connection between ARMORX and controller is unsuccessful. LED2 solid: Connection success.
• For Switch console: Navigate to System Settings > Controllers and Sensors > Pro Controller Wired Communication On.

Wired Connection

1. After attaching ARMORX to the Xbox Series controller, hold the power button to turn it on.
2. Connect the Type-C port of ARMORX to the console with a Type-C cable.
3. Check indicator lights: Both indicators solid green means wired connection is successful.

Note: 3.5mm audio jack is available only under wired connection.

Re-pair

If the ARMORX and adapter connection fails, follow these steps:

1. With ARMORX on, hold AB + FN until LED1 fast flashes to enter pairing mode.
2. Plug the adapter into the console and hold the pair button on the adapter until its indicator fast flashes to enter pairing mode.
3. When both LED1 and adapter indicator fast flash, they are pairing. Wait until both indicators become solid for successful re-pairing.

Hair Trigger

Activate hair trigger by pressing the trigger at any position.

1. Hold AB + Left trigger (LT): LED2 flashes cyan twice for hair trigger activation.
2. Hold AB + Right trigger (RT): LED2 flashes cyan twice for hair trigger activation.
3. LED2 flashes cyan when the trigger is pressed with hair trigger function enabled.
4. Double-click the hair trigger button to cancel all hair trigger functions.

Mapping Button

1. Mapping Setting: Press AB + (M1/M2/M3/M4). LED2 breathes green. Press the target button; LED2 flashes twice to confirm mapping.
2. Cancel Mapping: Hold the button to be canceled (M1-M4) and double-click AB. LED2 flashes twice in green to confirm cancellation.
3. Cancel All Mapping: Double-click AB. LED2 flashes twice in green to confirm cancellation.

Turbo Button

Supported buttons for TURBO: ABXY, D-pad, LT/RT/LB/RB, M1-M4, RS/LS.

1. Turbo Setting: Hold AB + the desired button. The controller vibrates for 0.2 seconds, and LED2 flashes twice in orange.
2. Cancel Turbo: Hold the button with turbo enabled and double-click AB. LED2 flashes twice in orange.
3. Cancel All Buttons' Turbo: Double-click AB. LED2 flashes twice in orange, canceling all turbo functions.
4. Change Turbo Frequency: Hold FN + ↑ to cycle through 5/s, 10/s, 20/s. (Turbo frequency is not affected by on-board profiles).

Macro Recording

Supported buttons for Macro: ABXY, D-pad, LT/RT/LB/RB, M1-M4, RS/LS.

1. Macro Recording: Press FN + (M1/M2/M3/M4). LED2 breathes red, indicating recording mode. Press controller buttons. Finish recording by pressing FN once; LED2 flashes twice. LED2 slowly flashes during macro execution.
2. Cancel Macro: Hold the button to be canceled (M1-M4) and double-click FN. LED2 flashes twice in red.
3. Cancel All Macro: Double-click FN. LED2 flashes twice in red.

Adjustment of Rumble Motor

1. Press FN + ← to change trigger motor vibration intensity (4 gears: strong, medium, weak, off).
2. Press FN + → to change handle motor vibration intensity (4 gears: strong, medium, weak, off).

On-Board Profile

ARMORX has 3 on-board profiles, switchable by clicking the profile switch button. LED1 on the left side indicates the profile:

• Orange: First profile
• Green: Second profile
• Blue: Third profile

Battery

The ARMORX has a 1300mAh battery providing up to 10 hours of use. Vibration intensity significantly affects battery life.

Charging power is 5V/1A, taking approximately 2 hours for a full charge.

• Low Battery: Controller vibrates 3 times, LED1 flashes red quickly, cycling every 5 minutes.
• Charging: LED1 is solid red while charging. LED1 is solid green when fully charged.

Detailed Functional Operation Instructions

For more detailed instructions, please visit the official BIGBIG WON website: https://www.bigbigwon.com/support/

Support and Community

Scan the QR code to watch a video tutorial or visit the official support page: www.bigbigwon.com/support.

For questions or issues, submit a support request via Amazon Product Page > Seller profile > "Ask a question" or contact Customer Service at support@bigbigwon.com.

Join the BIGBIG WON community on Discord and follow social channels for updates and events.

Social Media: Discord, Instagram, TikTok, Facebook, YouTube (@BIGBIGWON)