DEWERT OKIN RF426B Remote Control Instructions

Instruction of RF426B-16

Figure 1 shows the buttons of the remote control.

Button Functions:

1.1 Child Lock 🔒 (16)

Double-click the Child Lock button to lock or unlock the remote.

1.2 Bed Lamp 🌙 (6)

Click the bed lamp button to turn the light under the bed on or off.

1.3 TV 📺 (12)

Click the TV button; the bed moves to the TV position. Press and hold the TV button for 5 seconds until the backlight flashes to set the current position as the TV position.

1.4 Light 🔦 (13)

Click the light button to turn the light on or off at the front of the remote.

1.5 Music 🎶 (14)

Click the music button; the bed moves to the music position. Press and hold the TV button for 5 seconds until the backlight flashes to set the current position as the music position.

1.6 Lumbar Up ▲ (4)

Press and hold the LUMBAR UP button; the lumbar actuator moves out. It stops when released.

1.7 Lumbar Down ▼ (5)

Press and hold the LUMBAR DOWN button; the lumbar actuator moves in. It stops when released.

1.8 Head Up ▲ (7)

Press and hold the HEAD UP button; the head actuator moves out. It stops when released.

1.9 Head Down ▼ (8)

Press and hold the HEAD DOWN button; the head actuator moves in. It stops when released.

1.10 Foot Up ▲ (9)

Press and hold the FOOT UP button; the foot actuator moves out. It stops when released.

1.11 Foot Down ▼ (10)

Press and hold the FOOT DOWN button; the foot actuator moves in. It stops when released.

1.12 Zero-G ⌧ (11)

Click the ZG button; the bed moves to the Zero-G position. Press and hold the Zero-G button for 5 seconds until the backlight flashes to set the current position as the Zero-G position.

1.13 Head Massage 👊 (1)

Click the HEAD MASSAGE button; the head massage motor switches massage intensity. Massage intensity switches among 0, 1, 2, 3.

1.14 Massage Time ⏰ (3)

Click the MASSAGE MODEL button to change the massage time.

1.15 Foot Massage 👊 (2)

Click the FOOT MASSAGE button; the foot massage motor switches massage intensity. Massage intensity switches among 0, 1, 2, 3.

1.16 Flat ⎯ (15)

Click the FLAT button; the bed goes flat.

FCC Compliance

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IC RSS Warning

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

ISED RSS Warning

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radioexempts de licence.

L'exploitation est autorisée aux deux conditions suivantes:

• (1) l'appareil ne doit pas produire de brouillage, et
• (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.