Instruction Manual for GLEDOPTO models including: GL-C-301W Ultra Mini Wi-Fi 5 Inch 1 Tuya LED Smart Controller, GL-C-301W, Ultra Mini Wi-Fi 5 Inch 1 Tuya LED Smart Controller, Tuya LED Smart Controller, LED Smart Controller, Smart Controller
19 dic 2024 — Follow the instructions in the app to add the controller to wifi. 5. Power off the router connected during pairing, turn off the phone's WiFi, only turn on ...
Gledopto Ultra Mini Wi-Fi 5 in 1 Tuya LED Smart Controller | ExpertElectrical.co.uk
Gledopto Ultra Mini Wi-Fi 5 in 1 Tuya LED Smart Controller | Downlights Direct
WiFi 5in1 LED Smart Controller User Instruction GL-C-301W Product Parameter 17mm 42mm 38mm Product Model: GL-C-301W Input Voltage: DC 12-24V Output Current/Channel: 6A Max Total Output Current: 10A Max Communication Protocol: WiFi+Bluetooth+2.4G RF Suggested Wire Type: 0.5-1.5mm² (24-16AWG) Stripping Length: 8-9mm Material: Fireproof PC IP Rate: IP20 Operating Temperature: -20~45 Size: 42x38x17mm Function of Button Set: 1) Short press once: Switch current device function 2) Short press twice: Switch frequency 3) Short press three times: Enable/disable memory function. LED strip blinks 3 times to indicate enable/disable of memory function successfully (default is disabled, memory function remembers the on/off status before power outage) 4) Long press for 3 seconds: Reset controller (reback to RGBCCT after reseting) On/Off, Dimmer: Short press: Power On/Off. Long press: Adjust brightness (Assuming: Long press increases brightness, release and long press again decreases brightness). PUSH G G V+ V+ R G B C W Push: Short press: Power On/Off. Long press: Adjust brightness (Assuming: Long press increases brightness, release and long press again decreases brightness). Frequency Settings In order to be applicable to different power supplies, the frequency of device is selectable as 600Hz, 800Hz, 1000Hz, 2000Hz, 4000Hz, 8000Hz with default frequency 1000Hz. Short press twice "Set" key, the frequency will switch into the next one. The indicator will flash in Pink color and resume to previous color after "off" for 2 seconds. The rule of indicator flashing times for different frequency please refer to table Indicator Light Status White Yellow Blue Green Red Purple RGBCCT RGBW RGB CCT Dimmer Frequency switching Wiring Diagram RGBCCT: Under RGBCCT function, the RGBCCT strip can be connected to the device. RGBCCT LED Strip DC Power Supply Optional connection PUSH G G V+ V+ V1- V2- V3- V4- V5- PUSH G G V+ V+ / C W C W PUSH G G V+ V+ R G B N W PUSH G G V+ V+ R G B N W RGBW: Under RGBW function, the RGBW strip can be connected, without any connection to "N" terminal. RGBW LED Strip DC Power Supply Optional connection RGB: Under RGB function, the RGB strip can be connected, without any connection to "N" terminal. RGB LED Strip DC Power Supply Optional connection CCT: Under CCT function, two pieces of CCT strips can be connected, without any connection to "N" terminal,but the light strips will be controlled simultaneously. Dual Color LED Strip Dual Color LED Strip DC Power Supply Optional connection DIMMER: Under dimmer function, five pieces of single color strips can be connected, but the light strips will be controlled simultaneously. Sing Color LED Strip Sing Color LED Strip Sing Color LED Strip Sing Color LED Strip Sing Color LED Strip DC Power Supply Optional connection Configuration Steps Wi-Fi Configuration Steps: 1. Connect the controller to power correctly. 2. Enter the Smart Life APP, then click " + " in the top right corner, select "Add Device". 3. Swipe up on the left side of the screen, find "Lighting", and click on the "Light Source (Wi-Fi)" icon. 4. Follow the instructions in the app to add the controller to wifi. 5. Once add successfully, you can start using the controller. Bluetooth Configuration Steps: 1. Turn on the Bluetooth function on your phone and power on the controller. 2. Enter the Smart Life APP, then click " + " in the top right corner, select "Add Device". 3. Swipe up on the left side of the screen, find "Lighting", and click on the "Light Source (BLE)" icon. 4. Follow the instructions in the app to add the controller to wifi. 5. Power off the router connected during pairing, turn off the phone's WiFi, only turn on Bluetooth and 4G Mobile internet, then wait for 3-5 minutes to use the controller via Bluetooth. Remote Control Pairing/Unpairing Pairing: Turn off the controller, then power on after 10 seconds. Within 4 seconds of powering on, press the "On" button of any group on the RF remote control (see the user manual of each remote control for details). Any group "On" When the light strip connected to the controller flashes, it indicates connect with the remote control successfully. Unpairing: Turn off the controller, then power on after 10 seconds. Within 4 seconds of powering on, press the "Master On" button on the RF remote control or press the "On" button of the controller's group 5 times. When the light strip connected to the controller flashes, it indicates a disconnection from the remote control. 1-8 Compatible with 2.4G RF Remote Control Mode Description 1. Static Warm white 5. Static Green color 2. Static Day white color 6. Static Blue color 3. Static Cold white 7. 16 Million Color Gradient 4. Static Red color 8. RGB Color Jumping 9. Color Breathing (Brightness gradually changes from 100% to 0%, then back to 100% to 0% in sequence. Adjusting color or color temperature can switch colors in this mode, press the "M" key to exit this mode). Reset Method Press and hold the Set button for more than 3 seconds, the light strip flashes 1 times, indicating the reset is complete. Set PUSH G G V+ V+ R G B C W 1. Bafore turning on the power, please ensure that all wiring is correct and secure. Do not operate while the power is on. 2. Use the product under the rated voltage, Overvoltage or undervoltage may cause damage. 3. Do not disassemble the product, as it may cause fire and electric shock. 4. Do not use the product in direct sunlight, damp, high-temperature, or other harsh environments. 5. Do not use the product in metal shielded areas or near strong magnetic fields, as it will severely affect the wireless sianaltransmission of the product. * Due to our continuous adopfion of new technologies, the product specifications may change without prior notice. * This manual is for reference and guidance purposes only. t does not guarantee complete consistency with the actual product. Please refer to theactual product for practical applications. * The components and accessorles described in this manual do not represent the standard configuratlon of the product, The specific configurationis subject to the package contents. * All text, tables, and images in this manual are protected by relevant naional laws and may not be used without our company's permission. * This product is compatible with thirdpary products (such as apps, hubs, etc,) as stated in the gateway compatibility chart. However, ourcompany takes no responsiblty for any issues that may arise from changes made by third-paty products, resulting in incompatibility orthe partial loss of functionality GL-C-I-301WAdobe PDF library 15.00 Adobe Illustrator(R) 17.0