Dr. Brown's Insta-Feed™ Bottle Warmer

Instructions for Use

This document provides instructions for the Dr. Brown's Insta-Feed™ Bottle Warmer. Please read all instructions carefully before use.

Important Safeguards

• Read all instructions before operating. Detailed instructions are available online at drbrowns.co/intl.
• Failure to operate the product correctly can result in damage to the product, personal property, and cause serious injury.
• This appliance shall not be used or played with by children. Do not leave the cord within a child's reach. Close supervision is necessary when any appliance is used near children.
• Do not attempt disassembly or use with incompatible components. The use of accessory attachments not recommended by Handi-Craft Company may cause injuries.
• Do not touch hot surfaces. Use handles or knobs.
• ⚠️ CAUTION: Hot surface icon indicates the part will get hot during use, including the Sterilizing Lid and Adapter Ring. Be careful to avoid touching them when in use.
• To protect against electrical shock, do not immerse the cord or plug in water or other liquids.
• Close supervision is necessary when any appliance is used near children.
• This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
• Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts.
• Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.
• Misuse of the product may cause potential injury.
• The heating element surface is subject to residual heat after use.
• The use of accessory attachments not recommended by Handi-Craft Company may cause injuries.
• Do not use outdoors. Household and indoor use only.
• Do not let the cord hang over the edge of a table or counter or touch hot surfaces.
• Do not place on or near a hot gas or electric burner or in a heated oven.
• Extreme caution must be used when moving an appliance containing hot liquids.
• To operate, plug the cord into a wall outlet. To disconnect, turn any control to "off," then remove the plug from the wall outlet.
• Do not use the appliance for other than its intended use.
• Never immerse the warmer or power cord in water.
• When in use, the warmer contains hot water. Be careful to avoid spilling or splashing any water on yourself when removing contents from the warmer.
• Before serving, ensure food is at a safe temperature.
• Warming food for long periods is not recommended.
• Before feeding, pour a few drops of the liquid content from the baby bottle onto the back of your hand to test the temperature.
• CAUTION: Always check the content temperature of the bottle or the small jar before feeding your baby.
• Before servicing, unplug the cord from the wall outlet. Do not leave the cord within a child's reach.
• The preheating of the appliance is not necessary.
• A short power-supply cord is provided to reduce the risk resulting from becoming entangled in or tripping over a longer cord.
• CAUTION: Do not use an extension cord.
• This appliance is designed for domestic and similar applications such as: staff kitchen areas in shops, offices, and other working environments; farms; use by hotel, motel customers, and other accommodation environments; bed and breakfast environments.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to avoid hazard.
• Any maintenance servicing should be performed by an authorized service representative.
• Appliances are not intended to be operated by means of an external timer or separate remote-control system.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children without supervision.

Package Contents

• Insta-Feed™ Bottle Warmer
• Quick Reference Guide
• 2x Storage Caps

Specifications

Nominal voltage: 220-240 VAC / 50-60Hz / 500W

Parts of the Insta-Feed™ Bottle Warmer

The bottle warmer consists of the following parts:

1. Warming Chamber
2. Indicator Light
3. Power Button
4. Sterilizing Lid
5. Adapter Ring
6. Measuring Cup
7. Lift-Out Basket
8. Storage Caps

Visual representation: A diagram shows the main unit with numbered parts: the warming chamber, indicator light, power button, sterilizing lid, adapter ring, measuring cup, lift-out basket, and storage caps.

Warming Bottles and Food Jars

CAUTION: Always unplug the warmer before filling. Do not use the Sterilizing Lid for warming.

1. Remove the Measuring Cup from the rear of the warmer.
2. Add water to the Measuring Cup, following the Warming Guide on page 5 to determine the amount of water to add based on your bottle type.

Note: These amounts are a guide only. Many variables can affect the final temperature, such as starting temperature, size, and shape. Always test the temperature before feeding your baby.

Use distilled or non-mineral bottled water. Tap water contains minerals that shorten the life of this appliance.

3. Pour the water from the Measuring Cup directly into the Warming Chamber. Do not overfill, as overfilling may cause overheating or damage to the unit.
4. Replace the Measuring Cup and plug in the power cord.

Note: The first time the unit is plugged in, the warming cycle may begin automatically. If the Indicator Light is on, wait for the cycle to end (Indicator Light turns off) and allow the unit to cool for 10 minutes before use.

5. Place the bottle or food jar inside the Warming Chamber:
   • Wide Neck Bottle: Place directly into the Warming Chamber.
   • Narrow Bottle: Place the Adapter Ring on top of the Warming Chamber, then place the bottle in the chamber. The Adapter Ring centers the bottle over the heating plate for even warming.
   • Note: To prevent leakage with Dr. Brown's® bottles, remove internal parts, collar, and nipple/teat, and replace with the included Storage Cap.
   • Food Jar: Place the food jar into the Lift-Out Basket, then place the Lift-Out Basket into the Warming Chamber.
   • Note: Always remove the food jar lid before warming. After the cycle, stir food thoroughly for even temperature.
6. Press the Power Button. The Indicator Light will turn on, indicating the warming cycle has begun.

CAUTION: Always add water before pressing the Power Button. If the Power Button is pressed first, steam may form when water is added.

WARNING: DO NOT reach over the appliance while in use, as steam can cause burns and serious injuries. Do not touch hot surfaces during or immediately after use.

Note: If the Power Button is pressed without water, the unit will shut off automatically. Wait at least 10 minutes to cool before adding water and starting the cycle.

7. When the Indicator Light turns off, the warming cycle is done. Remove the bottle/food jar promptly to avoid overheating. Gently stir or swirl content for even warming. DO NOT shake.

Note: Always test the temperature before feeding. Adjust water amount as needed. If too cold, add more water next time; if too warm, use less water.

8. Wait at least 10 minutes for the warmer to cool before using again.

Diagrams show the following steps: 1. Plugging unit into power outlet. 2. Filling measuring cup with water. 3. Pouring water into warming chamber. 4. Plugging unit into power outlet. 5. Placing Wide Neck Bottle, Narrow Neck Bottle, and Food Jar into the unit. 6. Arrow pointing to power button. 7. Bottle in warming chamber. 8. Timer icon showing 10 minutes.

Warming Guide

*Room Temp = 72°F/22°C, Refrigerator = 39°F/4°C

WARNING: THIS TIME CHART IS APPROXIMATE FOR DR. BROWN'S® BOTTLE VESSEL SIZES. WARMING TIMES WILL VARY DEPENDING ON THE BOTTLE VESSEL SHAPE AND VOLUME.

CAUTION: NEVER FREEZE GLASS CONTAINERS, AS GLASS MAY BREAK. DO NOT USE THIS WARMER FOR FROZEN MILK OR FOOD. ALWAYS THAW FROZEN MILK OR FOOD OVERNIGHT IN THE REFRIGERATOR FIRST BEFORE WARMING.

CAUTION: DO NOT USE STERILIZING LID FOR WARMING.

Sterilizing Small Parts

CAUTION: Always unplug the warmer before filling.

The sterilize feature can be used for any small part safe for steam sterilization. DO NOT sterilize bottles in this sterilizer.

1. Add 2 oz / 60 mL of water directly into the Warming Chamber. Do not overfill, as overfilling may cause damage to the unit.
2. Place small parts (nipples/teats, pacifiers/soothers, etc.) to be sterilized in the Lift-Out Basket.
3. Place the Lift-Out Basket with small parts into the Warming Chamber.
4. Place the Adapter Ring on top of the Warming Chamber.
5. Place the Sterilizing Lid on top of the Adapter Ring.
6. Plug in the power cord and press the Power Button. The Indicator Light will turn on, indicating the sterilizing cycle has begun.

WARNING: DO NOT open Sterilizing Lid or reach over the appliance while in use, as steam will cause burns and serious injuries. Do not touch hot surfaces during or immediately after use.

7. When the Indicator Light turns off, the sterilizing cycle is done.
8. Allow the unit to cool for at least 10 minutes before removing the Sterilizing Lid, Adapter Ring, and Lift-Out Basket.

CAUTION: Be sure to observe the 10-minute cooling time as warmer parts and sterilized parts will be hot. Always remove the Sterilizing Lid carefully by the handle. Take care when removing the Sterilizing Lid as there may be some residual steam; keep hands and face away. Allow the steam to clear before reaching into the unit. Always retrieve the sterilized parts by removing the Lift-Out Basket.

Diagrams show the following steps: 1. Plugging unit into power outlet. 2. Placing parts in lift-out basket. 3. Placing basket in warming chamber. 4. Placing adapter ring. 5. Placing sterilizing lid. 6. Plugging in and pressing power button. 7. Bottle in warming chamber. 8. Timer icon showing 10 minutes.

Troubleshooting Tips

• If the warmer is not operating, check that the power cable is connected to the power outlet and water has been added to the warming chamber.
• If the Indicator Light does not come on or the warming cycle does not start, the warmer may be cooling down. Wait 10 minutes and try again.
• If the Indicator Light comes on upon plugging in but before the Power Button is pressed, it is possible the Power Button was pressed while the warmer was unplugged. Wait for the warming cycle to end (Indicator Light will turn off) and allow the unit to cool down for 10 minutes before using.
• If the bottle/food is too warm/too cold after the warming cycle, note that the Warming Guide only shows the approximate amount of water needed. Warming times are impacted by many variables, so adjust the amount of water added as needed. If the bottle/food jar is too cold, add slightly more water next time. If the bottle/food jar is too warm, use slightly less water next time.

Cleaning and Maintenance

CAUTION: ALWAYS TURN OFF, UNPLUG, AND ALLOW THE UNIT TO COOL BEFORE CLEANING.

Bottle Warmer Unit: Wipe the outer surface and the inside of the Warming Chamber with a damp cloth or sponge using mild liquid soap. Wipe with clean water and allow the unit to air dry. DO NOT SUBMERGE THE UNIT IN WATER.

Lift-Out Basket, Adapter Ring, Sterilizing Lid, and Measuring Cup: Dishwasher safe (top rack only) or wash with soapy water. Rinse with clean water and allow to air dry.

De-scaling the Insta-Feed™ Bottle Warmer

It is recommended to de-scale your Insta-Feed™ Bottle Warmer every four weeks to ensure the unit continues to work properly. To de-scale, follow these steps:

1. Unplug the appliance from power.
2. Mix 2 oz / 60 mL of white vinegar with 4 oz / 120 mL of water. DO NOT USE BLEACH.
3. Pour the white vinegar and water mixture directly into the Warming Chamber.
4. Allow the mixture to stand in the unit until any mineral deposits dissolve.
5. Discard the cleaning mixture and rinse with clean water.
6. Wipe the Warming Chamber dry with a cloth or allow to air dry.

NOTE: DO NOT USE BLEACH, HARSH ABRASIVES, OR SOLVENTS TO CLEAN THE WARMING CHAMBER OR HEATING ELEMENTS AS THEY MAY CAUSE PERMANENT DAMAGE AND WILL VOID THE WARRANTY.

Instructions are also available online at www.drbrowns.com.au.

Limited Product Warranty

The Dr. Brown's Insta-Feed™ Bottle Warmer includes a one-year warranty against defects in material and workmanship from the date of purchase. In the unlikely event of a malfunction or defect during the warranty period, please contact Handi-Craft's Customer Service. If outside of the US or Canada, please contact your local distributor. Proof of purchase will be required.

CAUTION: This warranty does not cover a defect caused by negligence, accidents, or improper use of the appliance.

Customer Service

If you experience unsatisfactory operation or have questions/comments, please contact your local Dr. Brown's distributor. See drbrownsbaby.com/distributors to find your local contact.

Product Markings

The product is marked with CE and model numbers AC185-INTL, AC220-INTL.

The WEEE symbol (crossed-out wheelie bin) indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased for environment-safe recycling.