Dr. Brown's Insta-Feed™ Bottle Warmer

Package Contents & Specifications

Package Contents: Insta-Feed™ Bottle Warmer, Quick Reference Guide, 2x Storage Caps

Specifications: Nominal voltage: 220-240VAC 50-60Hz 500W

Important Safety Instructions

READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS BEFORE USING THIS APPLIANCE

When using electrical appliances, precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following:

• Read all instructions.
• Do not touch hot surfaces. Use handles or knobs.
• CAUTION: The hot surface icon ⚠️ indicates the part will get hot during use, including the Sterilizing Lid and Adapter Ring. Be careful to avoid touching them when in use.
• To protect against electrical shock, do not immerse cord or plug in water or other liquids.
• Close supervision is necessary when any appliance is used near children.
• This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
• Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts.
• Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.
• Misuse of the product may cause potential injury.
• The heating element surface is subject to residual heat after use.
• The use of accessory attachments not recommended by Handi-Craft Company may cause injuries.
• Do not use outdoors. Household and indoor use only.
• Do not let cord hang over edge of table or counter or touch hot surfaces.
• Do not place on or near a hot gas or electric burner or in a heated oven.
• Extreme caution must be used when moving an appliance containing hot liquids.
• To operate, plug cord into wall outlet. To disconnect, turn any control to "off," then remove plug from wall outlet.
• Do not use appliance for other than intended use.
• Never immerse the warmer or power cord in water.
• When in use, the warmer contains hot water. Be careful to avoid spilling or splashing any water on yourself when removing contents from the warmer.
• Before serving, be sure food is at a safe temperature.
• Warming food for long periods is not recommended.
• Food should not be heated for too long.
• Before feeding, pour a few drops of the liquid content from the baby bottle onto the back of your hand to test the temperature.
• CAUTION: Always check the content temperature of the bottle or the small jar before feeding your baby.
• Before servicing, unplug cord from wall outlet. Do not leave cord within child's reach.
• The preheating of the appliance is not necessary.
• A short power-supply cord is provided to reduce the risk resulting from becoming entangled in or tripping over a longer cord.
• CAUTION: Do not use an extension cord.
• This appliance is designed for domestic and similar applications such as: staff kitchen areas in shops, offices and other working environments, farms, use by hotel, motel customers and other accommodation environments, bed and breakfast environments.
• Appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• If the supply cord is damaged it must be replaced by the manufacturer, its service agent, or similarly qualified person in order to avoid hazard.
• Any maintenance servicing should be performed by an authorized service representative.
• Appliances are not intended to be operated by means of an external timer or separate remote-control system.

Parts of the Insta-Feed™ Bottle Warmer

A diagram shows the components of the Insta-Feed™ Bottle Warmer, labeled 1 through 8:

• 1. Sterilizing Lid
• 2. Adapter Ring
• 3. Warming Chamber
• 4. Power Button
• 5. Indicator Light
• 6. Measuring Cup
• 7. Lift-Out Basket
• 8. Storage Caps (Narrow and Wide-Neck)

Warming Bottles and Food Jars

Always unplug the warmer before filling.

1. Remove the Measuring Cup from the rear of the warmer.
2. Add DISTILLED water to the Measuring Cup, following the Warming Guide on page 6 to determine the amount of water to add based on your bottle type.
   NOTE: These amounts are a guide only. There are many variables that can impact the final temperature of the bottle or food jar you are warming, such as starting temperature, size, and shape. Always test the temperature before feeding your baby.
3. Pour the DISTILLED water from the Measuring Cup directly into the Warming Chamber. Do not overfill, as overfilling may cause the bottle/food jar to be overheated or may cause damage to the unit.
4. Replace the Measuring Cup and plug in the power cord.
   NOTE: The first time the unit is plugged in, the warming cycle may begin automatically. If the Indicator Light is on upon plugging unit in, wait for the warming cycle to end (Indicator Light will turn off) and allow the unit to cool down for 10 minutes before using.
5. Place the bottle or food jar inside the Warming Chamber as outlined below:
   • Wide Neck Bottle: Place bottle directly into Warming Chamber.
   • Narrow Bottle: Place Adapter Ring on top of Warming Chamber, then place bottle in Warming Chamber. The Adapter Ring will keep your bottle centered over the heating plate for even warming.
     NOTE: To prevent leakage when warming Dr. Brown's® bottles, remove the internal parts, collar, and nipple/teat, and replace with the included Storage Cap.
   • Food Jar: Place food jar into the Lift-Out Basket, then place Lift-Out Basket in Warming Chamber.
     NOTE: Always remove the lid of the food jar prior to warming. After warming cycle is complete, be sure to stir food thoroughly until it is an even temperature throughout.
6. Press the Power Button. The Indicator Light will turn on, indicating the warming cycle has begun.
   CAUTION: Always add water and then press Power Button. If the Power Button is pressed first, steam may form when water is added.
   NOTE: If the Power Button is pressed without water added, the unit will shut off automatically after a short period. If this happens, wait at least 10 minutes to allow warmer to cool before adding water and starting warming cycle.
7. When the Indicator Light turns off, the warming cycle is done. Remove the bottle/food jar promptly to avoid overheating.
   NOTE: Always test the temperature before feeding your baby. Adjust the amount of water added to the warming chamber as needed; if the bottle/ food jar is too cold, add slightly more water next time. If the bottle/food jar is too warm, use slightly less water next time.
8. Wait at least 10 minutes to allow warmer to cool before using again.

Diagrams illustrate the steps:

• Step 1: Diagram shows plugging the unit into a wall outlet.
• Step 2: Diagram shows pouring distilled water from the measuring cup into the warming chamber.
• Step 3: Diagram shows the warming chamber with water.
• Step 4: Diagram shows plugging the power cord into the unit.
• Step 5: Diagram shows three ways to place items: Wide-Neck Bottle (directly in chamber), Narrow Bottle (with adapter ring), Food Jar (in lift-out basket).
• Step 6: Diagram shows the power button being pressed, with the indicator light illuminated.
• Step 7: Diagram shows the unit with the indicator light off, signifying the end of the warming cycle.
• Step 8: Diagram shows a timer icon with '10' inside, indicating a 10-minute cool-down period.

Warming Guide

Use Distilled Water Only. Using tap water may shorten the life of the unit and result in voiding the warranty.

*Room Temp = 72°F/22°C, Refrigerator = 39°F/4°C

WARNING: THIS TIME CHART IS APPROXIMATE FOR DR. BROWN'S® BOTTLE VESSEL SIZES. WARMING TIMES WILL VARY DEPENDING ON THE BOTTLE VESSEL SHAPE AND VOLUME. DO NOT USE THIS WARMER FOR FROZEN MILK OR FOOD. ALWAYS THAW FROZEN MILK OR FOOD OVERNIGHT IN THE REFRIGERATOR FIRST BEFORE WARMING. ALWAYS TEST TEMPERATURE BEFORE FEEDING!

Sterilizing Small Parts

Always unplug the warmer before filling.

1. Add 2 oz / 60 ml of DISTILLED water directly into the Warming Chamber. Do not overfill, as overfilling may cause damage to the unit.
2. Place small parts (nipples/teats, pacifiers/soothers, etc.) to be sterilized in the Lift-Out Basket.
3. Place the Lift-Out Basket with small parts into the Warming Chamber.
4. Place the Adapter Ring on top of the Warming Chamber.
5. Place the Sterilizing Lid on top of the Adapter Ring.
6. Plug in the power cord and press the ON Button. The Indicator Light will turn on, indicating the sterilizing cycle has begun.
7. When the Indicator Light turns off, the sterilizing cycle is done.
8. Allow the unit to cool for at least 10 minutes before removing the Sterilizing Lid, Adapter Ring, and Lift-Out Basket.
   NOTE: Be sure to observe the 10-minute cooling time as warmer parts and sterilized parts will be hot. Always remove the Sterilizing Lid carefully by the handle. Take care when removing the Sterilizing Lid as there may be some residual steam—keep hands and face away. Allow the steam to clear before reaching into the unit. Always retrieve the sterilized parts by removing the Lift-Out Basket.

Diagrams illustrate the steps:

• Step 1: Diagram shows plugging the unit into a wall outlet.
• Step 2: Diagram shows placing small parts into the lift-out basket.
• Step 3: Diagram shows the lift-out basket with parts placed inside the warming chamber.
• Step 4: Diagram shows placing the adapter ring on top of the warming chamber.
• Step 5: Diagram shows placing the sterilizing lid on top of the adapter ring.
• Step 6: Diagram shows plugging in the power cord and pressing the ON button, with the indicator light illuminated.
• Step 7: Diagram shows the unit with the indicator light off, signifying the end of the sterilizing cycle.
• Step 8: Diagram shows a timer icon with '10' inside, indicating a 10-minute cool-down period.

Troubleshooting Tips

• If the warmer is not operating, check that the power cable is connected to the power outlet and water has been added to warming chamber.
• If Indicator Light does not come on/warming cycle does not start, warmer may be cooling down. Wait 10 minutes and try again.
• If Indicator Light comes on upon plugging in but before ON button is pressed, it is possible the ON button was pressed while the warmer was unplugged. Wait for the warming cycle to end (Indicator Light will turn off) and allow the unit to cool down for 10 minutes before using.
• If bottle/food is too warm/too cold after warming cycle, note the Warming Guide only shows approximate amount of water needed. Warming times are impacted by many variables, so adjust the amount of water added as needed. If the bottle/food jar is too cold, add slightly more water next time. If the bottle/food jar is too warm, use slightly less water next time.

Cleaning and De-scaling

Cleaning the Insta-Feed™ Bottle Warmer and Parts

ALWAYS TURN OFF, UNPLUG, AND ALLOW THE UNIT TO COOL BEFORE CLEANING.

• Bottle Warmer Unit: Wipe outer surface and inside the Warming Chamber with a damp cloth or sponge using mild liquid soap. Wipe with clear water and allow unit to air dry. DO NOT SUBMERGE UNIT IN WATER.
• Lift-Out Basket, Adapter Ring, Sterilizing Lid, and Measuring Cup: Dishwasher safe (top rack only) or wash with soapy water. Rinse with clear water and allow to air dry.

De-scaling the Insta-Feed™ Bottle Warmer

It is recommended to de-scale your Insta-Feed™ Bottle Warmer every four weeks to ensure the unit continues to work properly. To de-scale, follow the steps below.

1. Unplug the appliance from power.
2. Mix 2 oz / 60 ml of white vinegar with 4 oz / 120 ml of distilled water. DO NOT USE BLEACH.
3. Pour the white vinegar and water mixture directly into the Warming Chamber.
4. Allow the mixture to stand in the unit until any mineral deposits dissolve.
5. Discard the cleaning mixture and rinse with clear water.
6. Wipe the Warming Chamber dry with cloth or allow to air dry.

NOTE: DO NOT USE BLEACH, HARSH ABRASIVES OR SOLVENTS TO CLEAN THE WARMING CHAMBER OR HEATING ELEMENTS AS THEY MAY CAUSE PERMANENT DAMAGE AND WILL VOID THE WARRANTY.

A copy of these instructions is also available online at www.drbrowns.com.au

Limited Product Warranty & Customer Service

Dr. Brown's Natural Flow® Insta-Feed™ Bottle Warmer includes a one-year warranty against defects in material and workmanship from date of purchase. In the unlikely event of a malfunction or defect during the warranty period, please contact your local distributor. You will be required to provide proof of purchase.

PLEASE NOTE: This warranty does not cover a defect that has been caused by negligence, accidents or improper use of the appliance. To keep your Insta-Feed™ Bottle Warmer in good condition and retain your warranty, USE ONLY DISTILLED WATER.

Customer Service: If you experience unsatisfactory operation or have questions/comments, please contact your local Dr. Brown's distributor. See drbrownsbaby.com to find your local contact.