Ozito Power X Change Tool Manuals

Ozito 18V Cordless Lawn Mower (PXCLMK-218)

Specifications

• Voltage: 18V x 2
• Cutting Diameter: 330mm
• Cutting Heights: 25-65mm (5 settings)
• No Load Speed: 3,400/min
• Grass Catcher: 30 litres
• Weight: 11.85kg

Standard Equipment

• Cordless Lawn Mower
• Safety Key

Warranty

5 Year Replacement Warranty. Return product to nearest Bunnings Warehouse with receipt. Contact customer service for assistance.

Warranty Void If:

• Operated on incorrect voltage.
• Damaged due to abuse, accidents, or alterations.
• Maintenance not performed as per manual.
• Tool is disassembled or tampered with.
• Used for professional, industrial, or high-frequency use.

Know Your Product

Parts include: Wheels, Battery Cover, Battery Cover Securing Latch, Height Adjustment Lever, Cord Clips, Grass Catcher Flap, Lower Handle, Upper Handle, Lock-off Button, Handle Securing Lever, Start/Stop Lever, Grass Catcher, Handle Fastening Screw, Lifting Handle. Accessory: Safety Key.

Setup & Preparation: Assembly

Fitting the Lower Handles

1. Place the lower handle into the mount. 2. Secure with a washer and fastening screw. 3. Repeat for the other side.

Fitting the Upper Handle

1. Align holes in upper and lower handles. 2. Insert handle securing lever bolt from inside. 3. Place washer and handle securing lever onto bolt. 4. Lock lever to secure. 5. Repeat for opposite side. Note: Select appropriate hole on upper handle for user height.

Securing the Cord

Ensure cord follows handle smoothly. Push supplied cord clip over cord and onto lower handle. Care should be taken not to pinch cord when folding handle.

Inserting & Removing the Batteries

Inserting the Batteries into the Mower

Note: Always use 2 batteries of the same capacity and charge state. 1. Pull securing latch, open battery cover. 2. Slide two batteries into mower, aligning ribs until they click. 3. Insert safety key (remove if not using immediately). 4. Close battery cover.

Removing the Batteries from the Mower

1. Pull securing latch, open battery cover. 2. Press battery release tab and remove batteries. 3. Close battery cover.

Fitting and Removing the Grass Catcher

WARNING! Only fit/remove when mower is OFF and motor has stopped. 1. Lift catcher flap, guide catcher over mower hooks. 2. Lower catcher and flap into place. 3. To remove, lift flap and remove catcher.

WARNING! Ensure no grass build-up in chute after emptying.

Grass Catcher Indicator

Indicator flap at rear shows when catcher is full (flap down).

Operation

3. Controls: Switching On and Off

Mower has a dual-action switch to prevent accidental start. 1. Press and hold lock-off button. 2. Pull start/stop lever towards handle to start, then release lock-off button. 3. Release start/stop lever to stop.

4. Mowing

Wear substantial footwear and long trousers. Clear lawn of debris. Check for wear/damage before/after impact. Replace worn/damaged blades.

Lawn Mowing Tips

Start mowing edges, overlap passes. Mow in straight lines. For long grass, use highest cutting height first, then lower for desired height to avoid overloading motor.

Adjusting the Cutting Height

Provides 5 heights (25-65mm). 1. Push lever down. 2. Adjust to desired height. 3. Release lever, ensure it's secure.

CAUTION! Be careful of fingers during height adjustment.

DO NOT MOW IN POOR VISIBILITY, RAIN, OR WET GRASS.

Maintenance

Removing and Fitting the Blade

WARNING! ALWAYS USE GLOVES. 1. Loosen blade bolt anti-clockwise with a 13mm socket (use timber to hold blade). 2. Remove bolt, washer, blade. Replace blade after 50 hours or 2 years. 3. Fit new blade over centre hole, align lugs. 4. Tighten bolt clockwise. Do not overtighten.

Cleaning, Maintenance and Storage

Keep nuts/bolts tight. Check catcher for wear. Replace worn parts. Use specified replacement blade/bolt. Be careful of fingers during adjustments. Store in dry, frost-free location away from children. Clean housing with a moist cloth/brush, not solvents. Check wheel threads.

Troubleshooting

Spare Parts

Order from Special Orders Desk at Bunnings Warehouse. Visit ozito.com.au or contact customer service.

Caring for the Environment

Dispose of tools responsibly. Recycle where facilities exist. Check local council for advice.

Description of Symbols

Includes symbols for Volts (V), Hertz (Hz), Watts (W), Amperes (mA), Diameter (Ø), No Load Speed (/min), Double Insulated (Π), Regulator Compliance Mark (RCM), Transformer Energy Rating (MEPS), Newton Meters (Nm), Thermal Cut-out Protection (130°C), Indoor Use Only, Lithium Ion Battery (Li-ion), Warning (⚠️), Do not store battery above 50°C (MAX.50°C), Recycle Battery (♻️), Do not incinerate, Do not get battery wet, Read instruction manual.

Electrical Safety

Follow basic precautions for mains-powered tools. Use approved extension leads. Protect supply with RCD (30mA or less). Double insulation provides added protection.

General Power Tool Safety Warnings

Includes warnings on work area safety, electrical safety, personal safety, and power tool use/care. Always stay alert, use PPE, prevent unintentional starting, and maintain tools.

Lawn Mower Safety Warnings

Emphasizes safe operation, including wearing appropriate clothing, clearing the area, inspecting blades, mowing in daylight, avoiding wet grass, using proper footing on slopes, and stopping the motor when leaving the machine or clearing blockages.

Ozito 18V Cordless Split Tube Blower (PXCBLSS-018)

Specifications

• Voltage: 18V
• No Load Speed: 12,000/min
• Max. Air Speed: 210km/hr
• Max. Air Volume: 105m³/h
• Weight: 1.93kg

Standard Equipment

• Cordless Blower
• Split Blower Tube
• Blower Tube Extension

Warranty

5 Year Replacement Warranty. Return product to nearest Bunnings Warehouse with receipt. Contact customer service for assistance.

Warranty Void If:

• Operated on incorrect voltage.
• Damaged due to abuse, accidents, or alterations.
• Maintenance not performed as per manual.
• Tool is disassembled or tampered with.
• Used for professional, industrial, or high-frequency use.

Know Your Product

Parts include: Blower Tube Extension, Split Blower Tube, Blower Tube Lock Tab, On/Off Switch, Sure Grip Handle. Compatible with Ozito Power X Change Battery & Charger.

Setup & Preparation: Assembly

Fitting the Blower Tubes

1. Align split blower tube with blower outlet. 2. Push tube onto blower until it clicks. 3. Align extension with split tube end, slide into place. 4. Rotate extension clockwise to lock. 5. Rotate anti-clockwise to remove.

Operation

2. Inserting & Removing the Battery

Inserting the Battery Pack

1. Align battery ribs with handle recess. 2. Slide battery in until it clicks.

Removing a Battery from the Blower

1. Press and hold battery release tab. 2. Slide battery out.

3. Controls

Switching On and Off

WARNING! Do not use with accessories. 1. Squeeze on/off switch to start. 2. Release switch to stop.

WARNING! Keep body parts away from inlet/outlet openings.

4. Operation: Blowing

Ideal for leaves, grass clippings, debris. Split tube for easy cleaning, full tube for paths/driveways. Hold firmly, squeeze switch, point air forward, move slowly. Move side-to-side, tube inches above ground. Be careful where air is pointed to avoid injury/damage. Be aware of others and animals. Avoid collisions with hard objects.

Maintenance

WARNING! Ensure tool is stopped and battery removed before maintenance. Keep air intake/vents clean. Do not use solvents for cleaning; use mild detergent on damp cloth. Stop if blower vibrates abnormally. No lubrication needed.

Troubleshooting

Spare Parts

Order from Special Orders Desk at Bunnings Warehouse. Visit ozito.com.au or contact customer service.

Caring for the Environment

Dispose of tools responsibly. Recycle where facilities exist. Check local council for advice.

Description of Symbols

Includes symbols for Volts (V), Hertz (Hz), Watts (W), Amperes (mA), Diameter (Ø), No Load Speed (/min), Double Insulated (Π), Regulator Compliance Mark (RCM), Warning (⚠️), Wear eye/ear protection, Do not use in rain, Keep bystanders away.

Battery and Charger Safety Warnings

Read all instructions. Do not use charger for other purposes. Protect charger from heat and damage. Do not disassemble. Keep away from children. Charge within specified temperature ranges. Do not incinerate batteries. Protect from moisture. Do not use damaged batteries. Store batteries properly. Do not expose to fire/excessive temperature.

Electrical Safety

Follow basic precautions for mains-powered tools. Use approved extension leads. Protect supply with RCD (30mA or less). Double insulation provides added protection.

Blower Safety Warnings

Wear protective clothing. Do not start upside down. Switch off and remove battery when not in use or unattended. Keep people/pets away. Maintain safe distance. Never direct nozzle at bystanders/pets. Do not handle with wet hands. Keep air intakes clear. Maintain stable stance. Do not use in enclosed/flammable spaces. Stay alert. Ensure tubes are not obstructed. Do not operate with loose hair/jewellery. Operate in daylight. Store out of reach of children. Use only as per manual. Keep screws tight.

Ozito 18V Cordless Grass Trimmer (PXCGTAS-018)

Specifications

• Voltage: 18V
• No Load Speed: 8,500/min
• Cutting Diameter: 240mm
• Weight: 1.3kg

Standard Equipment

• Grass Trimmer
• Safety Guard
• Flower Guard & Spindle Plate
• Adjustable Handle & Blades x 10

Warranty

5 Year Replacement Warranty. Return product to nearest Bunnings Warehouse with receipt. Contact customer service for assistance.

Warranty Void If:

• Operated on incorrect voltage.
• Damaged due to abuse, accidents, or alterations.
• Maintenance not performed as per manual.
• Tool is disassembled or tampered with.
• Used for professional, industrial, or high-frequency use.

Know Your Product

Parts include: Telescopic Shaft, Shaft Adjustment Collar, Adjustable Handle Knob, Adjustable Handle, Rear Handle, On/Off Trigger, Battery Seating, Flower Guard, Cutter Head, Safety Guard. Accessories: Blades x10. Compatible with Ozito Power X Change Battery & Charger.

Setup & Preparation: Assembly

Fitting the Safety Guard

1. Turn trimmer upside down. Align guard tabs with cutter head recess. 2. Slide guard in until it clicks.

WARNING! NEVER USE TRIMMER UNLESS SAFETY GUARD IS PROPERLY FITTED.

Fitting the Spindle Plate

1. Place spindle plate onto spindle, secure with provided screw.

Fitting the Secondary Handle

1. Place adjustable handle over bracket. 2. Secure with supplied locking knob.

Operation

Fitting the Flower Guard

Attach flower guard to motor housing.

Attaching a Blade

1. Place large hole in blade onto spindle plate mount. 2. Pull blade outwards to fit small hole into mount. 3. To remove, push blade towards centre and slide off.

2. Adjusting the Trimmer

Adjusting the Height

1. Loosen shaft adjustment collar. 2. Extend to desired height, retighten collar.

Adjusting the Secondary Handle

1. Loosen locking knob. 2. Rotate handle to desired position, tighten knob.

3. Controls & Operation

Inserting & Removing the Battery

Inserting: Align battery ribs with recess, slide until it clicks. Removing: Press and hold release tab, slide battery out.

Switching On and Off

CAUTION! Ensure trimmer is not contacting objects before starting. 1. Squeeze on/off trigger to start. 2. Release trigger to stop.

Using the Grass Trimmer

WARNING! Inspect area for wires/strings that could entangle blade. Hold with both handles. Move trimmer side-to-side at approx. 30° angle. Several passes for long grass. Release trigger to stop. Allow motor to stop completely.

WARNING! DO NOT OPERATE ON TREES, LADDERS, OR SCAFFOLDS.

WARNING! OBJECTS CAN BE THROWN AT HIGH SPEED.

NOTE: BEST RESULTS ON DRY GRASS.

CAUTION! BYSTANDERS MUST MAINTAIN 10M SAFE DISTANCE.

Troubleshooting

Maintenance

WARNING! Ensure tool is stopped and battery removed before maintenance. Keep ventilation slots clean. Blow air through housing. Clean housing with damp cloth/soft brush. Never immerse tool in liquid. No lubrication needed. Store in dry, frost-free location away from children.

Battery Protection System

Output cuts off when tool is overloaded or battery capacity is low. Release trigger to restart after overload. Recharge battery when low. Protection system does not damage tool.

Caring for the Environment

Dispose of tools responsibly. Recycle where facilities exist. Check local council for advice.

Description of Symbols

Includes symbols for Volts (V), Amperes (A), Hertz (Hz), Amp Hour (Ah), Regulator Compliance Mark (RCM), Warning (⚠️), Indoor Use Only, Do not charge above 40°C, Slow Blow Fuse (T3.15A), Double Insulated, Do not dispose in rubbish, Read Instruction Manual.

Electrical Safety

Follow basic precautions for mains-powered tools. Use approved extension leads. Protect supply with RCD (30mA or less). Double insulation provides added protection.

General Power Tool Safety Warnings

Includes warnings on work area safety, electrical safety, personal safety, and power tool use/care. Always stay alert, use PPE, prevent unintentional starting, and maintain tools.

Grass Trimmer Safety Warnings

Hold by insulated surfaces. Do not let cutting accessory contact hidden wiring. Not for persons with reduced capabilities unless supervised. Keep children/pets away. Use in daylight. Never operate with damaged guards. Switch on with hands/feet away from head. Never fit metal blades. Use only manufacturer parts. Remove battery when unattended or before maintenance. Inspect and maintain regularly. Store out of reach of children. Face blades away from people/animals. Remove battery when changing spools or clearing grass. Use both handles. Keep ventilation clear. Keep handles dry. Do not use if fatigued or under influence. Take breaks. Do not run while using. Never operate in rain. Never modify switches. Never reach under trimmer until stopped.

Ozito 18V Cordless Hedge Trimmer (PXHTS-570)

Specifications

• Input: 18V
• No Load Speed: 2,200 SPM
• Max. Cutting Capacity: Ø13mm
• Blade Length: 570mm
• Blade Cutting Length: 500mm max.
• Noise Rating: 94 dB
• Tool Weight: 1.93kg

Standard Equipment

• Cordless Hedge Trimmer
• Blade Cover
• Safety Guard & Fitting Screws x 2
• Front Handle & Fitting Screw

Warranty

5 Year Replacement Warranty. Return product to nearest Bunnings Warehouse with receipt. Contact customer service for assistance.

Warranty Void If:

• Operated on incorrect voltage.
• Damaged due to abuse, accidents, or alterations.
• Maintenance not performed as per manual.
• Tool is disassembled or tampered with.
• Used for professional, industrial, or high-frequency use.

Know Your Product

Parts include: Rotating Rear Handle, Rear Handle Lock x 2, Safety Switch, Front Handle, Safety Guard, Blade, Impact Guard, Battery Seating, On/Off Trigger, Front Handle Lock. Accessories: Blade Cover.

Setup & Preparation: Assembly

Blade Cover

Protects blade when not in use. Slide off before use, replace after operation.

WARNING! NEVER START TRIMMER WHILE BLADE COVER IS FITTED.

Safety Guard

Attach safety guard using supplied screws.

WARNING! NEVER USE TRIMMER UNLESS SAFETY GUARD IS FITTED.

Operation

Front Handle

1. Position front handle, ensure lock is on the right for correct electrical contact. 2. Fit and tighten screw securely while holding lock closed. Note: Tighten screw only with lock closed. 3. To adjust position, open lock, adjust, close lock to hold. Note: Ensure lock is fully closed for motor to start.

2. Inserting & Removing the Battery

Inserting the Battery Pack

1. Align battery ribs with handle recess. 2. Slide battery in until it clicks.

Removing the Battery Pack

1. Press and hold release tab, slide battery out.

WARNING! DO NOT USE UNSUPPORTED ATTACHMENTS/ACCESSORIES.

3. Controls

Rotating Rear Handle

Rotatable 90° left/right. 1. Slide locks back, rotate handle. Lock snaps back. 2. To return, release lock, rotate handle. Note: Lock won't pull back if trigger is pressed.

Switching On and Off

Requires two-handed operation (safety switch + trigger). 1. Press and hold safety switch on front handle. 2. Squeeze on/off trigger to start. 3. Releasing either switch stops the trimmer.

WARNING! TRIMMER MAY RUN FOR SECONDS AFTER SWITCHING OFF. ALLOW COMPLETE STOPPAGE.

Safety switches prevent unsafe operation. Ensure full assembly.

4. Operation

Top Cutting

Use wide sweeping motion. Slight downward tilt of blades in cutting direction for best results.

Side Cutting

Start at bottom, cut upwards. Trim hedge slightly narrower at top for uniform growth.

Maintenance

Sharpening the cutting blade

1. Start/stop trimmer until blade/guard offset. 2. Remove battery. 3. Clamp blade assembly, file teeth (remove minimal material). 4. Repeat for unsharpened edges. Note: Do not use dull/damaged blades.

Lubricating the blade

Apply light machine oil to top blade edge before/after use. 1. Remove battery. 2. Lay trimmer flat. Apply oil.

DO NOT OIL WHILE TRIMMER IS RUNNING.

Cleaning and Storage

Keep air intake/vents clean. Clean housing with damp cloth/soft brush. Stop if trimmer vibrates abnormally. Always fit blade cover before storing/transporting. Store indoors, dry, out of reach of children.

Troubleshooting

Caring for the Environment

Dispose of tools responsibly. Recycle where facilities exist. Check local council for advice.

Description of Symbols

Includes symbols for Volts (V), Hertz (Hz), Regulator Compliance Mark (RCM), Warning (⚠️), Read instruction manual, Do not use in rain, Wear suitable eye/ear protection, Sound power level (94dB).

Electrical Safety

Follow basic precautions for mains-powered tools. Use approved extension leads. Protect supply with RCD (30mA or less). Double insulation provides added protection.

General Power Tool Safety Warnings

Includes warnings on work area safety, electrical safety, personal safety, and power tool use/care. Always stay alert, use PPE, prevent unintentional starting, and maintain tools.

Hedge Trimmer Safety Warnings

Keep body away from blade. Do not remove material with moving blades. Switch off for clearing jams. Carry by handle with blade stopped. Fit blade cover for transport/storage. Hold by insulated surfaces only. Inspect hedge for foreign objects. Not for unsupervised persons/children. Keep children/pets away. Use in daylight. Never operate with damaged guards. Switch on with hands/feet away from blades. Use only manufacturer parts. Remove battery when unattended or before maintenance. Inspect and maintain regularly. Store out of reach of children. Face blades away from people/animals. Remove battery when changing spools or clearing guards. Use both handles. Keep ventilation clear. Keep handles dry. Do not use if fatigued or under influence. Take breaks. Do not run while using. Never operate in rain. Never modify switches. Never reach under trimmer until stopped.

Ozito 18V Lithium Ion 2.5Ah Battery (PXBP-250)

Specifications

• Input: 18V
• Battery Capacity: 2.5Ah Li-ion
• Power Consumption: 45Wh
• Weight: 0.46kg

Description of Symbols

Includes symbols for Volts (V), Alternating Current (ac/~), Direct Current (dc), Hertz (Hz), Amperes (A), Amp Hour (Ah), Lithium Ion Battery (Li-ion), Recycle Battery (♻️), Do not incinerate, Regulatory Compliance Mark (RCM), Warning (⚠️), Do not store/use above 50°C, Do not put in rubbish, Do not get battery wet, Do not store when charge is low (store 40-60%), Do not expose to rain.

Caring for the Environment

Dispose of tools responsibly. Recycle where facilities exist. Check local council for advice.

Battery & Charger Safety Warnings

Read all instructions. Do not use charger for other purposes. Protect charger from heat and damage. Do not disassemble. Keep away from children. Charge within specified temperature ranges. Do not incinerate batteries. Protect from moisture. Do not use damaged batteries. Store batteries properly. Do not expose to fire/excessive temperature. Use only original battery packs. Do not overcharge. Do not leave charged batteries in charger. Charge in dry conditions. Do not use deformed batteries. Never fully discharge. Never charge unsupervised.

Electrical Safety

Follow basic precautions for mains-powered tools. Use approved extension leads. Protect supply with RCD (30mA or less). Double insulation provides added protection.

Operation

1. Operation

Charging Your Lithium Ion Battery

Battery shipped in low charge; charge before use. Allow cycles for optimum performance. Compatible with Ozito Power X Change chargers. 1. Connect charger to mains (green LED flashes). 2. Insert battery into charger. 3. Remove battery when fully charged, disconnect charger. Note: Battery may become warm.

Battery Charge Indicator

Press button to check charge level: Red flashing (low charge), Red illuminated (fast charge), Green illuminated (full charge).

Battery Protection System

Ensures longevity. Output cuts off when tool is overloaded or battery capacity is low. Release trigger to restart after overload. Recharge when low. System does not damage tool.

Warranty

36 Month Replacement Warranty. Excludes consumable parts.

Ozito 18V Compact Fast Charger (PXCG-030C)

Specifications

• Input: 200-250V ~AC 50-60Hz, 72W
• Output: 20V DC, 3A
• Battery Charge Time: 30Min (PXBP-150), 40Min (PXBP-200), 50Min (PXBP-250), 60Min (PXBP-300), 75Min (PXBP-400), 120Min (PXBP-520), 100Min (PXUBP-520).

Description of Symbols

Includes symbols for Volts (V), Amperes (A), Hertz (Hz), Amp Hour (Ah), Read Instruction Manual, Indoor Use Only, Do not charge above 40°C, Slow Blow Fuse (T3.15A), Double Insulated, Do not dispose in rubbish, Regulatory Compliance Mark (RCM), Warning (⚠️).

Caring for the Environment

Dispose of tools responsibly. Recycle where facilities exist. Check local council for advice.

Battery & Charger Safety Warnings

Read all instructions. Do not use charger for other purposes. Protect charger from heat and damage. Do not disassemble. Keep away from children. Charge within specified temperature ranges. Do not incinerate batteries. Protect from moisture. Do not use damaged batteries. Store batteries properly. Do not expose to fire/excessive temperature. Use only original battery packs. Do not overcharge. Do not leave charged batteries in charger. Charge in dry conditions. Do not use deformed batteries. Never fully discharge. Never charge unsupervised.

Electrical Safety

Follow basic precautions for mains-powered tools. Use approved extension leads. Protect supply with RCD (30mA or less). Double insulation provides added protection.

1. Charging a Battery

WARNING! Charger should be protected by RCD (30mA or less). 1. Connect charger to power (green LED flashes). 2. Align and slide battery into charger. 3. Red LED illuminates during charging. 4. Green LED illuminates when charged.

Charger LED Indicator Lights

2. Maintenance

Disconnect charger before cleaning. Keep charger dry, out of reach of children. Clean enclosure with dry, soft cloth only. Never immerse charger in liquid. No other user-serviceable parts. Do not disassemble.