JLab Audio JBuds BT Bluetooth Earbuds
We're excited to have you rock with JLab Audio! We're proud of our products and stand behind them.
Your Warranty
[2-Year Limited Warranty] [US-Based Customer Support]
All warranty claims must meet JLab Audio authorization requirements and are solely at our discretion. Keep your proof of purchase to ensure your warranty coverage.
Contact Us
Email us at support@jlabaudio.com or visit intl.jlabaudio.com/contact
Register Now
Visit intl.jlabaudio.com/register for product updates, user guides, and FAQs.
First-time Setup: Bluetooth Pairing
Turn on Bluetooth in your device settings.
(Visual: Phone screen showing Bluetooth toggle switched ON.)Press and hold the button on the earbud for 10 seconds. Release.
The indicator light will flash red and blue, indicating pairing mode.
(Visual: Earbud showing the button and a red/blue flashing indicator light.)In your device's Bluetooth settings, select "JLab BT" to connect.
The indicator light will slowly flash blue during Bluetooth pairing.
(Visual: Phone screen showing Bluetooth settings with "JLab BT" selected and a slow blue flashing indicator light on the earbud.)
Regular Use
Once JLab BT is paired with your device, the earbuds will automatically connect to your Bluetooth device when turned on again. (Follow button function instructions).
Button Functions
- Volume Up: Single tap.
- Next Track: Press and hold for over 2 seconds.
- Power On: Press and hold for 3 seconds.
- Power Off: Press and hold for 5 seconds.
- Play/Pause/Answer/Hang Up: Single tap.
- Activate Siri (iOS) or "OK Google" (ANDROID): Double tap.
- Bluetooth Pairing: (Follow first-time setup: Bluetooth pairing instructions).
- Volume Down: Single tap.
- Previous Track: Press and hold for over 2 seconds.
Equalizer Modes
Short press both buttons to select different EQ settings. JBuds BT will cycle through 3 EQ settings:
- JLab Classic Mode (Beep): JLab C3TM signature sound, amplifies vocals and bass.
- Balanced Mode (Two Beeps): Balanced sound, no additional enhancement.
- Bass Boost Mode (Three Beeps): Amplifies bass and sub-bass.
Voice Prompts
- Power On: Beep
- Bluetooth Connected: 2 Beeps
- Low Battery: "Low Battery" (Below 20%)
- Power Off: Beep
Charging
Open the USB port, connect the cable to a computer or USB power source to charge. Ensure the charging power source is rated for 5V or less.
(Visual: Earbuds with USB port open, connected via USB cable to a computer and a wall adapter. Shows 'Charging' status with a red indicator light.)The indicator light will be solid red while charging and turn blue when fully charged.
(Visual: Earbuds showing 'Fully Charged' status with a blue indicator light.)
Accessories
First, insert the Cush Fin ear fin stabilizers, then insert the ear tips. Note: Styles and options may vary.
(Visual: Earbud with Cush Fin stabilizer and ear tip attached.)Rotate the ear fin stabilizers to the desired position.
(Visual: Diagram showing how to rotate the Cush Fin for a secure fit.)Try different ear tips and Cush Fin stabilizers to find the best fit.
(Visual: Illustration of trying different ear tip sizes and Cush Fin positions.)
Clip Usage
Attach the clip near the center of the cable.
(Visual: Clip being attached to the earbud cable.)Clip to the back or front of your shirt.
(Visual: Earbuds clipped to the front of a shirt.)
Connection Troubleshooting
Cannot see JLab BT on my device
Turn off Bluetooth, then turn it back on in device settings.
(Visual: Phone screen showing Bluetooth toggle switched OFF, then ON.)If you still don't see JLab BT, repeat First-time setup: Bluetooth pairing.
(Visual: Phone screen showing Bluetooth ON, but "JLab BT" is not listed.)
JLab BT did not reconnect to my device after powering on
In device settings, forget JLab BT.
(Visual: Phone screen showing Bluetooth settings with "JLab BT" selected.)Turn off Bluetooth, then turn it back on in device settings.
(Visual: Phone screen showing Bluetooth toggle switched OFF, then ON.)Repeat First-time setup: Bluetooth pairing.
(Visual: Phone screen showing Bluetooth ON, ready to pair.)
Connection Troubleshooting (Continued)
Bluetooth is connecting to an unwanted device
Note: JLab BT can remember up to 8 devices. It will attempt to automatically connect to the last used device.
If you have multiple devices connected to JLab BT, turn off Bluetooth on the unwanted device and turn on Bluetooth on the selected device.
(Visual: Phone screen showing multiple Bluetooth devices, with one selected for connection.)Press and hold the button for 10 seconds. Release. The indicator light will flash red and blue, indicating pairing mode. Select "JLab BT" in your device's Bluetooth settings to connect. The indicator light will slowly flash blue during Bluetooth pairing.
(Visual: Earbuds in pairing mode and phone screen ready to select "JLab BT".)
Warnings
- Ensure the USB port is closed and secured. This prevents damage from sweat and water. (Visual: USB port shown closed and secured, and then open with water drops indicating potential damage.)
- JLab BT earbuds need to be completely dry before charging. If exposed to moisture, internal components may be damaged. It is best to air dry before charging. (Visual: Earbuds being left to air dry.)
Precautions
- Avoid water or liquid entering the earbud ear tips or charging port.
- Avoid extreme heat, cold, and humidity.
- Avoid dropping or crushing the earbuds, pulling the cable with excessive force, or bending the cable at sharp angles.
- Earwax may build up in the earbud ear tips, reducing sound quality. Carefully clean earwax with a cotton swab or other small tool to improve sound quality.
- If you feel discomfort or pain, try lowering the volume or stopping use temporarily.
- If you experience persistent discomfort while using this product, discontinue use and consult your doctor.
- We recommend treating your earbuds like a pair of sunglasses and storing them in a safe place when not in use.
Support & Downloads
Shop Products | Product Notices | Burn-in Earbuds
JLab Audio + Burn-in Tool
Download on the App Store | GET IT ON Google Play
Visit us at intl.jlabaudio.com
