Data Logger RF Stick Quick User Guide
DLS Version: 1.0
Delivery Content
- 1 PC RF Stick
- 1 PC RF external antenna
- 1 PC Data Logger RF Stick Quick User Guide
1 Electrical Connection
Connect the RF Stick to the corresponding interface on the inverter. The Solis-1P5K-4G is used as an example in this manual. Please perform relevant operations as indicated below:
Illustration shows the Solis RF Stick being inserted into the 'COM' port of a Solis inverter. The text specifies to fasten the RF Stick securely and to rotate only the black circular part, not the silver cover.
2 Usage Methods and Notices
- Usage methods and key-press descriptions for the reset button.
- Do not remove the waterproof plug.
3 Logger Status
This section describes the status of the indicator lights on the logger and their implications.
| Item | Lights | Implication | Status Description |
|---|---|---|---|
| RUN | FLASH: Normal Running ON/OFF: Abnormal |
System Running Status | FLASH: Normal Running ON/OFF: Abnormal |
| COM | ON: Connected OFF: Fail to connect |
Communication status with inverter | ON: Connected OFF: Fail to connect |
| RF | ON: Connected OFF: Fail to connect |
Communication status with RF Gateway | ON: Connected (Please make sure both logger and RF gateway are powered on.) OFF: Fail to connect |
Normal operation:
- Power on for 3 seconds, RUN/SER/RF lights will flash simultaneously and then extinguish.
- After approximately 6 seconds, the RUN light will flash, indicating the system is running normally.
- After approximately 60 seconds, the COM light will remain on, indicating the logger has connected to the inverter.
- After 10 seconds to 3 minutes, the RF light will remain on, indicating the RF gateway has connected to the RF sub-device. (Connection time varies according to different situations.)
NOTES
Installation Requirements: The maximum distance between the RF gateway and the RF logger without shelter is 200 meters.
Through-wall Ability: The system can penetrate a maximum of 2 reinforced concrete walls (15cm thick each), with a total distance of less than 20 meters.
4 Abnormal State Processing
If the data on the platform is abnormal while the stick logger is running, please consult the following tables and use the status of the indicator lights to perform simple troubleshooting. If the issue persists or the indicator light status is not listed, please contact Customer Support. (Note: Please refer to the following tables for queries after the device has been powered on for at least 3 minutes.)
4.1 Communicate with inverter abnormal
| Lights | Fault Cause | Solution |
|---|---|---|
| RUN(Flash) COM(OFF) RF(ON) |
1. Connection between stick logger and inverter is loose. 2. Inverter does not match the stick logger's communication rate. |
1. Check the connection between the stick logger and the inverter. Remove and re-install the stick logger. 2. Check the inverter's communication rate to ensure it matches the stick logger's. |
4.2 Communicate with RF Gateway abnormal
| Lights | Fault Cause | Solution |
|---|---|---|
| RUN(Flash) COM(ON) RF(OFF) |
1. RF sub-device matching error. 2. RF sub-device has no power. 3. Long distance between RF gateway and RF sub-device, or too many through-walls. |
1. Contact customer service. 2. Check if the RF sub-device is powered on. 3. Change the RF gateway installation site. |
4.3 System runs abnormally
| Lights | Solution |
|---|---|
| RUN(ON/OFF) COM(ON) RF(ON) |
1. Press and hold the key for 5 seconds. Release when the COM light flashes, then reboot the logger. 2. Remove and re-install the stick logger. |
4.4 Power supply abnormal
| Lights | Fault Cause | Solution |
|---|---|---|
| RUN(OFF) COM(OFF) RF(OFF) |
1. Connection between stick logger and inverter is loose or abnormal. 2. Inverter power is insufficient. 3. Stick Logger is abnormal. |
1. Check the connection, remove and re-install the stick logger. 2. Check the inverter's output power. 3. Contact customer service. |
Contact
If you have any technical questions about our products, please contact us. Before contacting us, please confirm the following items:
- Equipment model
- Serial number of the datalogger
- Problem description
- Screenshot of the Status page in the configuration interface
Ginlong Technologies Co., Ltd.
No. 57 Jintong Road, Binhai Industrial Park, Xiangshan, Ningbo, Zhejiang, 315712, P.R.China.
Tel: +86 (0)574 6578 1806
Fax: +86 (0)574 6578 1606
Email: info@ginlong.com
Web: www.ginlong.com
Groene-Energiewinkel bv
Kloosterstraat 25A, NL-4901 HR Oosterhout NB, Nederland / The Netherlands
Website: www.groene-energiewinkel.nl
Tel: +31 (0)162 470 461
Fax: +31 (0)162 470 462
Email: info@groene-energiewinkel.nl
Website: www.groene-energiewinkel.be
KvK/Trade register: 20140846
BTW/VAT/MwSt/TVA: NL8194.07.367.801
Triodos bank IBAN: NL86 TRIO 0390 4703 41
ABN AMRO bank IBAN: NL81 ABΝΑ 0559 2947 00
