iLive IHB603B Bluetooth CD Radio Home Music System

Warnings and Precautions

• CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
• WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
• AVERTISSEMENT: Pour réduire le risque d'incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l'humidité.
• CAUTION: Use of any controls or adjustments or performance of procedures other than those herein specified may result in hazardous radiation exposure.
• WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
• WARNING: Do not place this unit directly onto furniture surfaces with any type of soft, porous, or sensitive finish. As with any rubber compound made with oils, the feet could cause marks or staining where the feet reside. Recommend using a protective barrier such as a cloth or a piece of glass between the unit and the surface to reduce the risk of damage and/or staining.
• WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause.
• CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• WARNING: Lithium batteries, like all rechargeable batteries are recyclable and should be recycled or disposed of in normal household waste. Contact your local government for disposal or recycling practices in your area. They should never be incinerated since they might explode.
• WARNING: Shock hazard - Do Not Open.
• AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR
• Mains Plug or Direct plug-in adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the Mains Plug or Direct plug-in adapter should be disconnected from the mains socket outlet completely.
• La fiche d'alimentation ou adaptateur de courant est utilisé comme dispositif de déconnexion et doit rester accessible pendant l'utilisation. Pour mettre l'appareil hors tension, la fiche ou adaptateur de courant doit être débranché de la prise de courant.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.
• No mezcle baterías viejas y nuevas.
• No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (ni-cad, ni-mh, etc.).
• CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN
• ATTENTION RISQUE D' ÉLECTROCUTION NE PAS OUVRIR
• WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
• WARNING: The battery, batteries, and battery pack shall not be exposed to excessive heat such as sunshine, fire, or the like.
• WARNING: The remote control supplied with this product contains a button-cell battery that could be accidentally ingested by children. Do not leave button-cell batteries accessible to children. If swallowed, promptly see doctor and call (202) 625-3333.
• The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
• The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
• This product utilizes a Class 1 laser to read Compact Discs. This laser Compact Disc Player is equipped with safety switches to avoid exposure when the CD door is open and the safety interlocks are defeated. Invisible laser radiation is present when the CD Player's lid is open and the system's interlock has failed or been defeated. It is very important that you avoid direct exposure to the laser beam at all times. Please do not attempt to defeat or bypass the safety switches.

Important Safety Instructions

1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. ?
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Special note: When placing your unit on a lacquered or natural finish, protect your furniture with a cloth or other protective material.

FCC Warnings

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Additional Warnings

• The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus. L'appareil ne doit pas être exposé aux écoulements ou aux éclaboussures et aucun objet ne contenant de liquide, tel qu'un vase, ne doit être placé sur l'objet.
• Battery shall not be exposed to excessive heat such as sunshine, fire or the like. Les piles ne doivent pas être exposées à de forte chaleur, tel qu'à la lumière du soleil, au feu ou autres choses de semblable.
• Caution marking is located at the rear or bottom of the apparatus. Attention marquage est situé sur le paneau arrière ou inférieur de l'unité.
• The marking information is located at the rear or bottom of apparatus. Le marquage est situé sur le paneau arrière ou inférieur de l'unité.
• This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts. ⚡

Features

• Supports Bluetooth v2.1
• CD player: CD, CD-R/RW
• Digital FM Radio (PLL)
• Digital clock
• Negative LCD display with white backlight
• Ambient blue LED light effects
• Wireless range: 33 feet
• 2 channel stereo sound
• Station memory presets (10 FM)
• Vertical-load disc player
• Motorized disc door
• Sleep timer
• Alarm
• 3.5mm audio input
• Preset EQ
• Digital volume control
• Last user's setting memory
• Built-in FM wire antenna
• Full-function remote
• Wall mountable
• DC power input: requires an AC/DC power adapter (included)

Included

• Remote control: requires a CR2025 battery (pre-installed)

Introduction

Power/Source/Alarm Off: Press to power the music system on, press and hold to power off. In on mode, press to switch between sources. Press to turn the alarm off.

Alarm/EQ: In off mode, press to begin setting the alarm. In on mode, press to adjust the preset EQ to Rock, Classic, Jazz, or Pop.

Clk Set/Sleep: In off mode, press and hold to begin setting the clock. In on mode, Press to begin setting the sleep timer.

Open: Press to open and close the CD door.

Volume: Press to adjust the volume.

Play/Pause: Press to play or pause a loaded CD or a connected Bluetooth device.

Skip/Search Tune (+/-): Press to skip between tracks on a connected Bluetooth device. Press and hold to search through an individual track. Press to tune the FM radio. Press and hold to search for the next available station.

Pair/Stop: Press and hold to begin connecting a Bluetooth device. Press to stop a CD during play.

Mode/Memory: Press to program tracks to play in a specific order. In FM Radio mode, press and hold to begin saving a station as a preset.

USB Charger: Connect a USB device to charge.

Line In: Connect audio input.

Setup

Power

AC power input: requires an AC/DC power adapter (included).

Diagram: An illustration shows the AC power adapter being plugged into a wall outlet and the other end into the back of the music system.

Remote

Requires 1, CR2025, battery (pre-installed).

WARNING: The remote control's button cell battery contains mercury. Do not put in the trash, instead recycle or dispose of as hazardous waste.

Diagram: An illustration shows a CR2025 lithium battery and a diagram of the remote control's battery compartment with instructions on how to open and close it using the 'PUSH' and 'OPEN' indicators.

Clock

Setting the Clock

1. Press and hold the Power button to turn the music system off.
2. Press and hold the CLK Set/Sleep button on the music system. The display will flash.
3. Press the Skip/Search buttons to adjust the hour. The hour will begin to blink on the display.
4. A "PM" indicator will appear on the display when the time is set to the PM.
5. Press the CLK Set/Sleep button to set the adjusted hour. The minute will begin to blink on the display.
6. Press the Skip/Search buttons to adjust the minute.
7. Press the CLK Set/Sleep button to finish setting the clock.

Setting the Alarm

1. With the unit powered off, press and hold the Alarm/EQ button. The display will flash.
2. Press the Skip/Search buttons to adjust the hour.
3. A "PM" indicator will appear on the display when the time is set to the PM.
4. Press the Alarm/EQ button to set the adjusted hour. The minute will begin to blink on the display.
5. Press the Skip/Search buttons to adjust the minute.
6. Press the Alarm/EQ button to set the adjusted minute. The alarm source will begin to blink on the display.
7. Press the Skip/Search buttons to adjust the alarm source (bu-Buzzer, rad-Radio, Cd-CD).
8. Note: Please refer to the Radio and CD sections for additional information on the preferred settings.
9. Press the Alarm/EQ button to finish setting the alarm.
10. The unit will power on when the set time is reached.
11. To cancel the alarm, press the Alarm/EQ button once. To turn it back on, press the Alarm/EQ button again.

Bluetooth Setup & Charging

Pairing a Bluetooth Device

1. Power on the unit by pressing the Power button.
2. Press the Source button to switch to Bluetooth Mode. The display will show the flashing letters “bt”.
3. Press and hold the Pair button. "BT" will flash quickly on the display.
4. When pairing, remain within 3 feet of the unit.
5. Using the native controls on your Bluetooth device, select the "IHB603" in your Bluetooth settings to pair. If your device requests a password, enter the default password “0000”. Refer to the user's manual for your specific device for instructions on pairing and connecting Bluetooth devices.
6. When successfully paired, the pairing indicator will remain solid. After initial pairing, the unit will stay paired unless unpaired manually by the user or erased due to a reset of the device.
7. If your device should become unpaired, follow the above steps again.
8. If any pairing issues should occur, unpair the unit on your Bluetooth device and follow the above steps again.

Playing Audio Wirelessly

1. Follow the instructions for Pairing a Bluetooth Device.
2. Use the native controls on the connected Bluetooth Device to select a track.
3. To play, pause or skip the selected track, use the native controls on the connected Bluetooth Device or press the Play/Pause or Skip/Search buttons.
4. Audio played through the connected Bluetooth device will now be heard through the speakers.

Charging a Device

1. Make sure the unit is plugged into the wall.
2. Using the appropriate USB charging cable (not included), connect one end to the device and the other to the Charger on the unit. Refer to the user's manual for your specific device for manufacturers required charging amperage as well as determining the appropriate cable for your device before charging. Note: This device uses a USB charging port with a 500mA maximum charging capacity, making it unsuitable for charging iPads.
3. The device will now charge.

CD, FM Radio & Line In

Loading a CD

1. Open the Disc Door by pressing the Open button.
2. Place a CD into the unit, label side facing up.
3. Close the Disc Door.

Playing a CD

1. Follow the instructions for Loading a CD.
2. Press the Source button to switch to CD mode.
3. Press the Play/Pause button to begin playing the loaded CD.

Programming a CD

1. Follow the instructions for Loading a CD and Playing a CD.
2. Press the Stop button to stop the CD during play.
3. Press the Prog button on the remote.
4. Use the Skip/Search buttons to enter the desired track number. Press the Prog button to set the track.
5. Repeat step 3 until the desired number of CD tracks are programmed.
6. Press the Play/Pause button on the remote to begin playing the programmed tracks.

Playing the Radio

1. Press the Source button to switch to FM Radio mode.
2. Press the Tune+/- buttons to tune the radio. Press and hold to search for the next available station.

Radio Reception

Adjust the position of the antenna to improve FM radio reception.

Saving a Radio Station as a Preset

1. Follow the instructions for Playing the Radio.
2. Press the Prog button on the remote.
3. Press the Tune+/- buttons on the remote to select a preset number. Up to 10 stations may be preset.
4. Press the Prog button to save the current station to the selected preset.

Tuning to a Saved Preset Station

1. In FM Radio mode, press the Mem+ button to cycle through saved presets.

Using the Audio Input

Requires a 3.5mm audio cable (not included)

1. Connect a 3.5mm audio cable to the Line In and the audio output on an MP3 player or other audio device.
2. Press the Source button to switch to Line In mode.
3. Use the native controls on the connected MP3 player or other audio source to play your audio through the unit.

Company Information

International Support

To download this User's Guide in English, Spanish, or French, or to get answers to frequently asked questions, visit the support section at www.iLiveElectronics.com.

Para descargar este Manual del Usuario en inglés, español y francés, o para obtener respuestas a preguntas frecuentes, visite la sección de apoyo en www.iLiveElectronics.com.

Pour télécharger ce guide de l'utilisateur en anglais, espagnol ou français, ou pour obtenir des réponses à des questions fréquemment posées, consultez la rubrique d'assistance sur www.iLiveElectronics.com.

Contact Information

Email Support: prodinfo@dpiinc.com

Email Parts: partsinfo@dpiinc.com

Phone Support: 1-888-999-4215

Website: www.iLiveElectronics.com

Warranty

For Warranty Information and the most up-to-date version of this User's Guide, go to: www.iLiveElectronics.com

Green Initiative

MADE GREEN protect for today sustain for tomorrow

Environmental Commitment to 'Protect for Today and Sustain for Tomorrow'. On a continual basis DPI, Inc. is making efforts to sustain the environment and improve the recyclability of its products and packaging.

Focusing on "protecting for today and sustaining for tomorrow” DPI, Inc. has committed to reducing packaging size, increasing the usage of recyclable plastics, and ensuring that packaging and manuals are made with up to 85% recycled material. In addition to material consideration, DPI, Inc. has also focused on the finer details that positively impact the environment such as employing the usage of soy-based inks.

DPI, Inc. also ensures that the factories that produce the company's wide variety of consumer electronics adhere to environmentally friendly air and water restrictions. This is yet another example that every step of the way DPI, Inc. is making efforts to lessen any impact on the environment.

In 2011 DPI, Inc. also began conversations with Energy Star in order to ensure that the consumer electronics being produced meet high standards of energy efficiency. The ultimate goal is keeping energy costs for consumers low while providing quality, feature-rich products.

Copyright © 2013 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners. Specifications are subject to change without notice.