NZXT Control Hub
Digital RGB Lighting & Fan Speed Controller
Hardware Introduction
This section details the physical components and ports of the NZXT Control Hub.
- NZXT Control Hub: The central unit for managing lighting and fan speeds.
- Ports:
- A1: 8-pin PCIe Power Connector
- A2: Internal USB 2.0 Connector (for motherboard communication)
- A3: 8-pin (PWM Only) - For PWM fans requiring only PWM signal.
- A4: 8-pin (DC+PWM) - For fans requiring both DC voltage and PWM signal.
- A5: 4-pin NZXT RGB - For NZXT's proprietary RGB lighting accessories.
- A6: 4-pin PWM (DC+PWM) - Standard 4-pin PWM connector for fans.
Component List ?️
- NZXT Control Hub (x1)
- NZXT 8-pin splitter (x1)
- NZXT RGB splitter (1 to 3 split) (x1)
- 4-pin PWM Fan splitter (1 to 3 split) (x1)
- 3M Dual Lock fasteners (x2)
Installation ⚙️
Step 1: Power Connection
Ensure your PC is turned off. Connect the PCIe power cable from the controller to the PCIe power cable on your power supply unit (PSU).
Step 2: Motherboard Connection
Connect the USB cable from the Control Hub to an available internal USB 2.0 port on your motherboard.
Step 3: Fan and RGB Connection
Connect 8-pin NZXT RGB fans directly to an available 8-pin port on the hub. ℹ️ Note: For case version RGB fans, connect them to Channel 4, which supports RPM control for DC fans.
Splitters (Optional)
Use the included splitter cables as needed to connect multiple fans and RGB accessories to a single hub port.
⚠️ Warning: Do not use more than one 1-to-3 splitter per channel to avoid overloading.
Controller Mounting
The Control Hub can be mounted in your PC case using one of the following methods:
- Magnets: The controller features built-in magnets on its rear side. Place this side close to a magnetic surface within your PC case to attach it securely.
- 3M Dual Lock: Apply one side of the Dual Lock tape to the rear of the controller, and the other side to your desired mounting surface. Press firmly to secure. This is intended for a single application.
- M3 Screws: The Control Hub has two screw holes compatible with standard M3 screws. Mount it onto any 2.5" drive tray or bracket. Ensure adequate clearance for headers and connectors. Use M3 screws typically found in your PC case accessory box.
Software Setup
To unlock the full control capabilities of the NZXT Control Hub, download and install the NZXT CAM software from nzxt.com/software/cam.
Compatibility Warning ⚠️
- The NZXT Control Hub is compatible with all NZXT RGB fans and lighting products.
- Each NZXT RGB channel supports a maximum of 40 LEDs.
- The 8-pin ports on the hub support up to a total of 96 LEDs per channel.
- When connecting 3-pin fans, ensure you use channels that specifically support DC voltage fan control.
- Do not mix different types of NZXT lighting accessories (e.g., F-series RGB Fans, Aer RGB Fans, LED strips) within the same channel, as this can cause compatibility issues.
Regulatory & Compliance Information
Declarations of Conformity
This device complies with the essential requirements set out in the Council Directives relevant to Union harmonisation legislation, including the EMC Directive 2014/30/EU and the RoHS Directive 2011/65/EU & (EU) 2015/863.
UKCA Declaration of Conformity
The object of the declaration is in conformity with the relevant UK harmonisation legislation: Electromagnetic Compatibility Regulations 2016, Electrical Equipment (Safety) Regulations 2016, and The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.
RoHS Statement
This product is compliant with RoHS (Restriction of Hazardous Substances) regulations implemented worldwide, including China, India, Japan, Korea, and the European Union.
REACH Statement
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals, EC 1907/2006) is the European Union's chemical substances regulatory framework. NZXT Inc. provides customers with information on Substances of Very High Concern (SVHC) contained in products in concentrations above 0.1% weight by weight (w/w) to allow for safe use of the product.
Environmental Compliance (WEEE)
In accordance with the European Union ("EU") Directive on Waste Electrical and Electronic Equipment (Directive 2002/96/EC), products of "electrical and electronic equipment" cannot be discarded as municipal waste. NZXT complies with product take-back requirements for NZXT-branded products sold into the EU. You can return these products to local collection points.
FCC & ISED Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device also complies with CAN ICES-003(B) / NMB-003(B).
RoHS/REACH Component Compliance
The following table details the compliance of components with restrictions on hazardous substances:
| Unit | Lead (Pb) | Mercury (Hg) | Cadmium (Cd) | Hexavalent Chromium (Cr+6) | Polybrominated Biphenyls (PBB) | Polybrominated Diphenyl Ethers (PBDE) |
|---|---|---|---|---|---|---|
| Wire | ○ | ○ | ○ | ○ | ○ | ○ |
| Plastic | ○ | ○ | ○ | ○ | ○ | ○ |
| Metal | ○ | ○ | ○ | ○ | ○ | ○ |
| Motherboard | ○ | ○ | ○ | ○ | ○ | ○ |
○: Indicates the content of the hazardous substance in all homogeneous materials of the component is within the limit requirements specified by GB/T 26572.
Note: Lead is present in ceramic or glass in electronic components on circuit boards, which is an exclusion under EU Directive 2011/65/EU.
NZXT Global Warranty Policy ?
This NZXT Global Warranty Policy governs the sale of products by NZXT to you. Any replacement product will be covered under warranty for the remainder of the warranty period or thirty days, whichever is longer. Proof of purchase is required for warranty service.
I. Warranty Length
Refurbished NZXT Product: NZXT Controller - 2 Years
II. Who is Protected
The Warranty covers only NZXT products purchased by the original consumer.
III. What is and is Not Covered
Please note that our warranty is not an unconditional guarantee. If the product, in NZXT's reasonable opinion, malfunctions within the warranty period, NZXT will provide you at its sole discretion with a repaired or replacement product, either new or refurbished, with a similar function that is equal or greater in value depending on supply. Our warranty does not cover the following:
- Any product or serial number/warranty sticker modification applied without permission from NZXT.
- Any damage that is not a manufacturing defect.
- Damage, deterioration, or malfunction resulting from: accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions included with the product.
- Improper installation, unauthorized alterations or modifications, or repair or attempted repair by anyone not authorized by NZXT.
- Shipping or transport damage (claims must be made with the carrier).
- Normal wear and tear.
NZXT does not warrant that this product will meet your requirements. It is your responsibility to determine the suitability of this product for your purpose. For NZXT Store orders, NZXT covers two-way return shipping for all exchanges and returns. For all other authorized dealers, NZXT Support does not cover return shipping and only covers one-way shipping from NZXT back to the end user for exchanges. Two-way expedited shipping is provided for all PSUs covered under the Less Than Three program, indiscriminate of purchase location, provided the location is an approved NZXT reseller.
For information on warranty coverage and service, please visit nzxt.com/warranty and support.nzxt.com.
