HOTO Electric Precision Screwdriver ADV

Usage of the storage case

Flip cover opening/closing:

• Lift the lid of the storage case to its natural opening state; the maximum opening angle is 115°. Please do not force it open.
• Put down the lid of the storage case to 0° until the storage case is closed.

Screwdriver storage:

• Insert the screwdriver sleeve into the round hole as shown in the picture, and then press down on the rear of the screwdriver to store it.
• Screwdriver bits are stored in the bottom shell by magnetic attraction.
• After use, place the screwdriver bit into its slot; it will be attracted by itself.

Usage method of the electric screwdriver:

Take out the screwdriver bit from the storage case and insert it into the sleeve.

Magnetizing instructions:

When a screwdriver bit is not sufficiently magnetic, place it at the magnetization area for 5 seconds to instantly magnetize. Magnetism may weaken after long storage, requiring regular magnetizing treatment.

Controls:

Forward/reverse button:

• Press "⬆️" to unscrew or loosen the screw.
• Press "⬇️" to screw in or tighten the screw.

Gear switching toggle:

• Push the gear switching button to switch between gear "I" and "II".
• Push forward to gear "I" and push backward to gear "II".

Indicator light state:

• When power is lower than 20% during operation, the red indicator light flashes quickly and turns off when the button is released. Please charge in time.
• While charging, the red indicator light shows a breathing style.
• When the battery is full, the white indicator light stays on.

This product is equipped with a Type-C general charging cable.

Work area safety:

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres (e.g., presence of flammable liquids, gases, or dust). Power tools create sparks that may ignite dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause loss of control.

Electrical safety:

• Power tool plugs must match the outlet. Never modify the plug. Do not use adapter plugs with earthed (grounded) power tools.
• Avoid body contact with earthed or grounded surfaces (pipes, radiators, appliances). There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool increases the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging. Keep cords away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
• When operating outdoors, use an extension cord suitable for outdoor use.
• If operating in a damp location is unavoidable, use a residual current device (RCD) protected supply.

Personal safety:

• Stay alert, watch what you are doing, and use common sense. Do not use while tired or under the influence of drugs, alcohol, or medication.
• Use personal protective equipment. Always wear eye protection. Protective equipment like dust masks, non-skid shoes, hard hats, or hearing protection reduces personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power or battery, picking up, or carrying the tool.
• Remove any adjusting key or wrench before turning the power tool on.
• Do not overreach. Maintain proper footing and balance at all times for better control.
• Dress properly. Do not wear loose clothing or jewelry. Keep hair and clothing away from moving parts.
• If dust extraction facilities are provided, ensure they are connected and used properly.
• Do not let familiarity gained from frequent use lead to complacency or ignoring safety principles. A careless action can cause severe injury.

Power tool use and care:

• Do not force the power tool. Use the correct tool for your application.
• Do not use the power tool if the switch does not function correctly.
• Disconnect the plug or remove the battery pack before making adjustments, changing accessories, or storing the tool.
• Store idle power tools out of reach of children and do not allow untrained persons to operate them.
• Maintain power tools and accessories. Check for misalignment, binding, or breakage. If damaged, have the tool repaired before use.
• Use the power tool, accessories, and bits in accordance with instructions, considering working conditions.
• Keep handles and grasping surfaces dry, clean, and free from oil and grease.

Battery tool use and care:

• Recharge only with the charger specified by the manufacturer.
• Use power tools only with specifically designated battery packs.
• When the battery pack is not in use, keep it away from other metal objects to prevent short-circuiting.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact occurs, flush with water. If liquid contacts eyes, seek medical help.
• Do not use a damaged or modified battery pack or tool.
• Do not expose a battery pack or tool to fire or excessive temperature (above 130°C).
• Follow all charging instructions and do not charge outside the specified temperature range.

Service:

• Have your power tool serviced by a qualified repair person using only identical replacement parts.
• Never service damaged battery packs. Service should only be performed by the manufacturer or authorized providers.

Safety instructions for all operations:

• Hold the power tool by insulated gripping surfaces when performing operations where accessories may contact hidden wiring.

Safety instructions when using long drill bits:

• Never operate at higher speed than the maximum speed rating of the drill bit.
• Always start drilling at low speed with the bit tip in contact with the workpiece.
• Apply pressure only in direct line with the bit and do not apply excessive pressure.

Additional safety information:

• Secure the workpiece.
• Always wait until the power tool has come to a complete stop before placing it down.
• Switch the power tool off immediately if the application tool becomes blocked.
• Use suitable detectors to determine if there are hidden supply lines or contact the local utility company for assistance.

Battery Handling:

• Hold the power tool securely. Be prepared for temporarily high torque reactions.
• In case of damage or improper use of the battery, vapors may be emitted. Ensure the area is well ventilated and seek medical attention if adverse effects occur.
• Do not open the battery.
• The battery can be damaged by pointed objects or external force.
• Only use the battery with products from the manufacturer.
• Protect the battery against heat, fire, dirt, water, and moisture.
• Power Adapter Output: 5V === 0.2A Max.
• Ambient Temperature while Charging: 1 to 40°C.
• WEEE Symbol: ♻️ All products bearing this symbol are waste electrical and electronic equipment (WEEE) and should not be mixed with unsorted household waste. Protect human health and the environment by handing over waste equipment to a designated collection point for recycling.