Rubicson Wake-up Light

Overview

Specifications

Use

Power on/off

Connect the included USB-C charging cable between the USB-C power input (5) and a USB charger (sold separately). The wake-up light time display (4) lights up and shows the set time.

Note: The USB charger must support an output of at least 9 V/2 A (18 W). If the charger does not meet the requirements, the wake-up light LED bed lamp may start to flicker, emit weak light, or cause distorted sound from the speaker. These requirements are commonly found in chargers certified for QC (Quick Charge) or PD (Power Delivery). It is not recommended to use a multi-port USB charger, as connecting multiple devices may reduce the charger's output power. Contact the place of purchase if unsure about your USB charger's compatibility.

Setting the time

Press and hold the Time settings button (9) for 2 seconds. The hour will flash. Use the Up (11) and Down (12) buttons to change the value. Press the Time settings button again to set the minutes, using the Up and Down buttons. Press the Time settings button to confirm and return to the time display. The wake-up light will emit a chime sound to confirm the time has been set.

When the current time is displayed, pressing the Time settings button will toggle between 12-hour and 24-hour formats. In 12-hour format, the corresponding LED indicators (3) below the AM/PM markers (15) will illuminate to indicate AM or PM.

Alarms

The wake-up light features two alarms. The LED indicators (3) in front of the alarm markers (16) will light up to show which alarm is being set or is active. The type of sound and its volume can be configured in the settings.

• Alarm 1 plays a sound when activated.
• Alarm 2 slowly turns on the LED bed lamp (1) 10 minutes before the set alarm time, plays a sound, or can combine both functions.

Setting an alarm

Press the Alarm button (14). The LED indicator (3) will flash, showing the set alarm time and which alarm is currently selected. Press the button again to switch between alarm 1 and alarm 2. Press the Up button (11) to turn on the selected alarm, and the Down button (12) to turn it off. A solid light on the LED indicator signifies an active alarm; it turns off when the alarm is deactivated.

Note: The wake-up light display will revert to showing the time after 5 seconds of inactivity.

To enter alarm settings, press and hold the Alarm button (14) for 2 seconds. The time display will flash along with the indicator for the selected alarm. Use the Up button (11) to select alarm 1, or the Down button (12) to select alarm 2. Press the Alarm button to access the settings for the displayed alarm.

The hour will flash. Use the Up and Down buttons to set the hour. Press the Alarm button to set the minutes. Press the Alarm button again to confirm.

Set the alarm volume using the Up and Down buttons, from "V01" (lowest) to "V12" (highest). Press the Alarm button to confirm.

Select the alarm sound by using the Up and Down buttons, choosing from 01-15 available built-in sounds:

• 01. Piano lullaby
• 02. Marimba
• 03. Old telephone
• 04. Calm melody
• 05. Lively melody
• 06. Bird song
• 07. Ocean waves
• 08. Babbling brook
• 09. Bonfire
• 10. Summer night
• 11. Thunderstorm
• 12. Electric fan
• 13. Rain
• 14. Music box
• 15. Ticking clock

Press the Alarm button, or wait 10 seconds, to confirm and exit alarm settings. The wake-up light will emit a chime sound and return to displaying the time.

Note: To have Alarm 2 wake you using only the LED bed lamp, set the volume to "V00" when setting the alarm. This option is only available for Alarm 2.

When an alarm is activated, it will sound for 30 minutes, until turned off, or paused using the Snooze button (10).

Snooze

When an alarm is active, press the Snooze button (10) to pause the sound for 10 minutes. Press and hold the button, or snooze the alarm 3 times consecutively, to turn off the alarm sound for the day. The alarm will repeat the next day at the set time.

Tap the LED bed lamp ring to turn off the bed lamp's wake-up function for the day.

Light and Settings

Back light settings

While the display shows the current time, press the Snooze button (10) multiple times to cycle through the display's backlight settings: brightest, medium bright, slightly dimmed, and off.

Light

Touch anywhere on the LED bed lamp ring (1) to manually turn the light on. Press the LED bed lamp ring multiple times to select one of the three available light levels: slightly dimmed, medium bright, and brightest. Tapping the bed lamp again at the brightest setting will turn it off.

Touch and hold your finger on the LED bed lamp ring for 2 seconds to activate the breathing light effect. Press and hold again for 2 seconds to turn this effect off.

Sleep timer

Press the Sleep sound button (8) to start playing the built-in sounds. Press the button multiple times to cycle through the available sounds (listed as 06-15 under "Setting an alarm"). Press and hold the button to turn off the sleep sounds.

When a sleep sound is playing, press the Sleep timer button (13) multiple times to set the sleep timer to 30, 60, or 90 minutes. Pressing again after 90 minutes will stop the sleep timer. The LED indicator (3) on the far left of the display will illuminate, and the wake-up light will emit a chime sound to confirm the sleep timer is active. Use the Up and Down buttons (11, 12) to adjust the sound volume. Press the Sleep timer button to view the remaining time, or press it again shortly after to change the timer to the next setting.

When the countdown timer reaches 0, the sound will stop.

Note: If the LED bed light is turned on before setting the sleep timer, the light will also turn off when the sleep timer countdown finishes.

Time Backup

The wake-up light has a built-in time backup feature that helps preserve settings during a power outage or disconnection from power. When power is restored, the wake-up light will resume with the correct time. The time backup function can last up to 3 hours, depending on how long the wake-up light was connected to power before the outage.

Troubleshooting

LED bed lamp flickers, light is low, or sound is distorted

The USB charger does not meet the power requirements. The USB charger must deliver at least 9 V/2 A (18 W). These requirements are typically found in chargers certified for QC (Quick Charge) or PD (Power Delivery).

Using a multi-port USB charger is not recommended, as connecting multiple devices can reduce the charger's output power. If you are unsure whether your USB charger meets the requirements, please contact the retailer.