YITAHOME DXL-V1 PSPPPC-4002 Cat Litter Box Enclosure & Cat Tree Assembly Guide

Assembly Instructions Overview

Before beginning assembly, please ensure all parts are present. Assemble on a flat, clean, and soft surface. Do not fully tighten screws until all parts are assembled. Professional installation is highly recommended.

(Note: The following instructions are provided in English for clarity and conciseness, merging multilingual content from the original document.)

Parts List

Item No.	Reference Image Description	Quantity
A	Base enclosure panel (55 X 48CM)	X1
B	Side enclosure panel (55 X 48CM)	X1
C	Front enclosure panel with cat cutout (55 X 48CM)	X1
D	Back enclosure panel with cat cutout (49 X 58CM)	X1
E	Enclosure door (56.5 X 47.5CM)	X1
F	Bottom platform (55 X 60CM)	X1
G	Middle platform (55 X 60CM)	X1
H	Upper platform (55 X 58CM)	X1
I	Side panel with circular cutout (28 X 34CM)	X1
J	Side panel with guitar-shaped cutout (28 X 31CM)	X1
K	Side panel with large circular cutout (28 X 34CM)	X1
L	Top platform with cushion (29 X 32CM)	X1
M	Top panel (34 X 34CM)	X1
N	Cushion	X1
O	Ramp	X1
P	Bowl ?	X1
Q	Scratching post panel	X1
R	Back panel for enclosure	X1
a	Long threaded posts (for platforms)	X2
b	Medium threaded posts (for platforms)	X1
c	Short threaded posts (for top cushion)	X2
d	Screws (M8 X 60MM) ?	X3
e	Screws (M8 X 40MM) ?	X5
f	Screws (M8 X 13MM) ?	X2
g	Dowels/Pegs ⚙️	X24+5 extra
h	Screws (M3 X 12MM) ?	X24+5 extra
i	Screws (M6 X 40MM) ?	X24+5 extra
j	Screws (M4 X 25MM) ?	X1
k	Allen wrench ?	X1
m	(Unused/Unclear)
n	Connectors/Brackets	X4
o	Screws (M6) ?	X4
p	Screws (M4 X 40MM) ?	X1
q	Screws (M4 X 40MM) ?	X1
r	Wall mounting bracket	X1
s	Screws (M3 X 12MM) ?	X8
t	Wall screw ?	X1
u	Wall anchor	X1
v	Bracket/Connector	X1

Note: Item numbers in the diagrams (e.g., 'a', 'b', 'c') correspond to the hardware listed. Some parts are labeled with letters (A-R) for the main components.

Assembly Steps

Step 1: Base Assembly

Attach part A (base enclosure panel) to parts n (connectors) using screws h ?. Insert dowels g ⚙️ into the designated holes on part A. Place parts n onto the dowels. Secure with screws h ?.

Diagram shows part A with four holes on its underside. Four connectors (n) are shown being attached to these holes using screws (h). Dowels (g) are also shown being inserted into part A.

Step 2: Enclosure Walls

Connect parts B (side enclosure panel) and C (front enclosure panel with cat cutout) to part A using dowels g ⚙️ and screws h ?. Part D (back enclosure panel with cat cutout) is also attached similarly.

Diagram shows parts B, C, and D being attached to the base panel A. Dowels (g) are inserted into the edges of A, and screws (h) are used to secure B, C, and D to A.

Step 3: Attaching Door and Side Panel

Attach part E (enclosure door) ? to part B using dowels g ⚙️ and screws h ?. Attach part J (side panel with guitar-shaped cutout) to the assembly using dowels g ⚙️ and screws h ?.

Diagram shows door E being attached to panel B. Panel J is shown being attached to the side of the enclosure. Dowels (g) and screws (h) are used.

Step 4: Platform Assembly

Place part F (bottom platform) onto the assembled enclosure. Secure it using screws d (M8 X 60MM) ?. Attach long threaded posts (a) ? and medium threaded post (b) ? to part G (middle platform) using screws o (M6) ? and dowels g ⚙️. Attach part V (bracket/connector) using screws s ?.

Diagram shows platform F being placed on top of the enclosure and secured with screws (d). Posts (a) and (b) are shown being attached to platform G. Part V is also attached.

Step 5: Further Enclosure Construction

Attach part G (middle platform) to the enclosure using dowels g ⚙️ and screws h ?. Attach part E (door) ? and part B (side panel) to the enclosure structure using dowels g ⚙️ and screws h ?. Attach part C (front panel) using dowels g ⚙️ and screws h ?.

Diagram shows the enclosure structure being built up. Part G is attached. Panels E, B, and C are connected to the base and potentially to each other using dowels (g) and screws (h).

Step 6: Adding Shelves and Scratching Post

Attach part H (upper platform) to the structure using screws e (M8 X 40MM) ?. Attach part Q (scratching post panel) ? to platform H using screws f (M8 X 13MM) ?. Attach part P (bowl) ? to platform H using screws e ?.

Diagram shows platform H being attached. Scratching post panel Q is attached to H. Bowl P is also attached to H. Screws (e) and (f) are used.

Step 7: Assembling Upper Levels

Attach part I (side panel with circular cutout) to the assembly using dowels g ⚙️ and screws h ?. Attach part J (side panel with guitar-shaped cutout) and part K (side panel with large circular cutout) using dowels g ⚙️ and screws h ?.

Diagram shows panels I, J, and K being connected to form the upper section of the cat tree. Dowels (g) and screws (h) are used.

Step 8: Finalizing Upper Structure

Connect the assembled upper panels (I, J, K) to platform H using dowels g ⚙️ and screws h ?. Ensure all connections are secure.

Diagram shows the upper section being finalized and attached to the main structure. Dowels (g) and screws (h) are used for connections.

Step 9: Attaching Top Platform

Place part L (top platform with cushion) ?️ onto the assembled upper structure. Arrows ⬇️ indicate it slides into place.

Diagram shows the top platform L being placed onto the uppermost part of the cat tree. Arrows indicate the direction of placement.

Step 10: Securing Top Panel

Attach part M (top panel) to the structure using dowels g ⚙️ and screws h ?. Ensure all connections are secure.

Diagram shows the top panel M being attached to the structure. Dowels (g) and screws (h) are used for fastening.

Step 11: Attaching Cushion

Insert short threaded posts (c) ? into the underside of the cushion (N) ?️. Attach the cushion assembly to the top panel (M) using these posts.

Diagram shows two short posts (c) being inserted into the cushion (N). The cushion assembly is then shown being attached to the top panel (M).

Step 12: Final Enclosure Panel Attachment

Attach part R (back panel for enclosure) to the main structure using screws e (M8 X 40MM) ?. This step appears to be a final reinforcement or attachment for the back of the enclosure.

Diagram shows part R being attached to the rear of the assembled cat tree/enclosure. Screws (e) are used.

Step 13: Wall Mounting (Optional)

For added stability ✔️, the unit can be fixed to the wall. Use wall screw (t) ? and wall anchor (u) with bracket (r) and screw (h) ? to secure the unit to a wall. This step is labeled "fixed on the wall" in multiple languages.

Diagram shows a bracket (r) being attached to the top of the unit (part H) and then to a wall using a screw (t) and anchor (u).

Step 14: Installation Completed

The installation is now complete ?. The document shows the fully assembled cat litter box enclosure and cat tree.

Diagram shows the fully assembled product. Text indicates "Installation Completed" in multiple languages.

Contact Information

If you have any questions about the installation of YITAHOME products, please email us at after-sale.cs@hotmail.com.

Alternative method for Amazon.co.uk orders:

Log into your Amazon account.
Go to "Your Orders" and find the purchase.
Click on "Contact Seller".

	YITAHOME DXL-V1 Cat Litter Box Enclosure Assembly Instructions Comprehensive assembly guide for the YITAHOME DXL-V1 Cat Litter Box Enclosure (Models PSPPPC-4005, PSPPPC-4006). Includes parts list, step-by-step instructions, and contact information.
	YITAHOME ZJHN-V3 Cat Cage Assembly Guide and Product Information Comprehensive installation guide for the YITAHOME ZJHN-V3 cat cage (PSPPPC-0016). Includes parts list, step-by-step assembly instructions, and contact details.
	Yitahome Pure & Easy Cactus Cat Tree House Assembly Instructions DQAS-V1 Comprehensive assembly guide for the Yitahome Pure & Easy Cactus Cat Tree House (Model DQAS-V1). Includes detailed parts list, step-by-step instructions, safety warnings, and troubleshooting tips.
	YITAHOME ZCCW-V1 Enclosed Cat Litter Box Assembly Guide Assembly instructions and parts list for the YITAHOME ZCCW-V1 enclosed cat litter box, models FTPLRP-3001 and FTPLRP-3002.
	YITAHOME ZJXD-V1 Cat Cage Assembly Guide Detailed assembly instructions for the YITAHOME ZJXD-V1 41-inch, 2-Tier plastic cat cage (model FTPLRP-2002). This guide provides a comprehensive parts list and step-by-step instructions for setting up your pet enclosure, featuring wheels and a ladder.
	YITAHOME ZJXD-V1 Cat Litter Box Installation Guide Comprehensive installation guide for the YITAHOME ZJXD-V1 enclosed cat litter box, detailing parts and assembly steps for easy setup.
	YITAHOME ZJXD-V1 Cat Cage Assembly Guide Detailed assembly instructions for the YITAHOME ZJXD-V1 cat cage, including a comprehensive parts list and step-by-step guidance. Learn how to easily assemble your multi-tier cat enclosure.
	Yitahome HBMTN-V1 Cat Litter Cabinet Installation Guide Comprehensive installation guide for the Yitahome HBMTN-V1 Cat Litter Cabinet, featuring a scratch post, feeding station, shelves, and charging station. Includes detailed parts list and step-by-step assembly instructions.