Hampton Bay Intelligent Landscape Transformer Use and Care Guide

Contact Information

Questions, problems with the Hubspace App? Please call Hubspace Customer service
8 a.m. - 7 p.m. PST Monday - Friday and 9 a.m. - 6 p.m., PST, Saturday at 1-877-592-5233

HOMEDEPOT.COM / HUBSPACE

Thank You

We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this transformer. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Hampton Bay!

Safety Information

1. Proper mounting, wiring, grounding and servicing.
2. The secondary wiring is intended for shallow burial (less than 6 in. (152 mm).).
3. Risk of fire, do not place insulation under terminal plate. Check connection after installation.
4. For use only on a branch circuit protected by a class a type ground fault circuit interrupter.
5. For use with landscape lighting systems only.
6. This device is accepted as a component of a landscape lighting system where the suitability of the combination shall be determined by CSA or local inspection authorities having jurisdiction.
7. Do not connect two or more power supplies in parallel.
8. Landscape lighting systems are for outdoor use only.
9. Not for use in dwelling units.
10. Do not mount power supply or luminaries within 3 m of a swimming pool or spa.
11. The supply circuit for the landscape lighting system shall be protected by a class a type ground fault circuit interrupter, unless it is provided with the landscape lighting system.
12. A cord-connect landscape lighting system shall not be used with an extension cord.

WARNING: Make sure there is no wire insulation under the clamping plate.

WARNING: Do not coil the cable around the transformer.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

IMPORTANT: This landscape light system must be installed in accordance with all local codes and ordinances. If you are experiencing problems, contact a qualified electrician.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. FCC responsible party name: Eaglerise E&E Inc. Address: 320 Constance Dr., Unit 1 Warminster, PA 18974. Telephone number: 267-387-6022. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

WARNING: Risk of Electric Shock. Install power unit 5 feet (1.5 m) or more from a pool, spa, or fountain. Where the power unit is installed (a) indoors within 10 feet (3.0 m) of a pool, spa, or fountain or (b) outdoors, connect power unit to a receptacle protected by a GFCI.

WARNING: For outdoor installations use UL Listed Underground low energy circuit cable or SPT-3 or SPT-2W. Failure to use at least 16-gauge minimum cable or install it as directed in these instructions may result in Risk of Fire or Electric Shock. Using large cable will ensure maximum light output.

WARNING: Do not use an extension cord, the unit shall be connected to a GFCI protected hooded flush type cover plate receptacle marked "Wet Location".

Warranty

WHAT IS COVERED

The manufacturer warrants this transformer to be free from defects in materials and workmanship for a period of two (2) years from date of purchase. This warranty applies only to the original consumer and only to products used in normal use and service. If this product is found to be defective, the manufacturer's only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer's discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling.

WHAT IS NOT COVERED

This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.

Contact the Customer Service Team at (877)592-5233 or visit HOMEDEPOT.COM/HUBSPACE.

Pre-installation

TOOLS REQUIRED

• Hammer
• Wire stripper
• Wire cutter
• Phillips screwdriver

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

Package Contents

A diagram showing the transformer (A), mounting template (B), power button (C), terminals (D), resettable circuit breaker (E), and AC power cord (F).

Installation

1. Preparing the cable

• Use caution when splitting to avoid exposing copper wire.
• Remove 1/2 in. of insulation from both wires and twist the ends.

A diagram illustrating the preparation of the cable, showing 1/2 inch of insulation removed.

2. Connecting the cable to the transformer

• Lay the transformer (A) on a flat, stable surface and open the terminal connector door flap.
• Insert the landscape wires into the desired channel pair of terminals marked "COM_" & "CH_" with one stripped end into the desired channel marked "COM1” or “COM2” or “COM3” and firmly press down the terminal handle to secure the wire.
• Next insert the remaining paired stripped wire into the matched paired terminal marked "CH1” or “CH2” or “CH3” and firmly press down the terminal handle to secure the wire.
• Refer to the Cable Selection Chart to determine which voltage terminal to select "12V" or "15V” based on the wire gauge and fixture wattage.
• Verify that there are no loose cable strands and tug on the landscape wire to verify that the connections are all secure, and firmly close the flap door.

Diagrams showing how to insert and pull the wire into the transformer terminals.

3. Placing the fixtures and routing the cable

• Lay the fixtures (not included) in their desired locations. Be sure they do not exceed the 200-watt rating of the transformer.
• Route the low voltage cable to the fixtures. If there is extra cable, coil the cable after the last fixture.

A diagram illustrating the placement of fixtures and routing of the low voltage cable in a landscape setting.

4. Mounting the transformer

• Mount the transformer (A) directly to a wall surface within 12 in. to 48 in. (0.3 m to 1.2 m) of the ground using the included screws (AA). See the mounting template (B) for the correct spacing of the screws (AA).
• Drill two holes on the wall using the mounting template (B), insert two wall anchors (BB) into the wall, and insert the screws (AA) into the wall anchors (BB).
• Hang the transformer (A) onto the screws (AA).

Diagrams showing the mounting template and the transformer being hung on screws.

5. Attaching the fixtures

• Attach the fixtures to the cable using the cable connectors (not included) as shown. Press the connector tight onto the cable until the prongs pierce the cable insulation.

A diagram showing how to attach fixtures to the cable using connectors.

6. Protecting or hiding the cable

• Once all fixtures are in place, the cable may be covered with mulch or buried up to 6 in. (15 cm) deep. Leave about 12 in. (30 cm) of cable after the last fixture.

7. Unit Power-up

• Press power button to turn on, the LED button light and connected fixtures shall illuminate.
• Press the power button again to turn off.

LED state | Definition

LED on | There is voltage output and the fixtures are on.

LED off | There is no voltage output and the fixtures are off.

LED flash | Power is overloaded or short circuit.

Note: 1. When installing the fixtures, the button LED light must be turned off to avoid the risk of electric shock

2. After trouble shooting, you need to press the button again, and the product will resume normal operation.

Diagrams showing the transformer in the OFF and ON states.

Operation

1. Let's Get Started!

• Download the Hubspace™ app from the App Store or the Google Play Store to your mobile device.
• Launch the app.
• To register, enter your email address and a password. Or, login if you already have an account.
• Bluetooth access is required for device setup.

2. Verify your network

• This Hubspace device requires a 2.4GHz Wi-Fi channel.
• Most routers provide a 2.4 GHz WiFi channel.

3. Add a device

• In the Hubspace app, tap the plus sign in the upper right corner.
• Scan your product's QR code. You can find a copy of the QR code on the device itself and in the Quick Start Guide.
• Scan problem? If the QR code cannot be scanned for some reason, you can enter the code manually. Tap Enter Code and follow the instructions.
• Connect your device to power and follow the instructions on screen.

4. Set up your voice assistant

• In the Hubspace app, tap the Hubspace button.
• Select the Integrations tab, choose your voice assistant and follow the instructions.

5. 12V or 15V Voltage Switch

• Your transformer can output 12V or 15V and ships with 12V activated.
• To change the voltage:
• Add the device in the Hubspace app.
• Ensure the device is powered on and online in the app.
• Tap the button on top left corner and select desired Output Voltage. Default is 12V.

6. 3-Zone Control

The transformer has 3 zones of control that can be turned on or off and scheduled in the Hubspace app. See the app for details.

7. Power Meter

• The power meter provides the total power connected to the transformer.
• The power meter allows you to see how much capacity remains for adding additional fixtures to your system.
• Do not exceed the maximum rated wattage of the unit.
• The power meter reading is a sum of the following:
  1. Power consumed by all attached fixtures for each powered zone.
  2. Power losses from the low-voltage wire(s)

8. System Overload

• If your transformer detects a system overload it will shut off. The indicator light will flash.
• Follow these steps to check for possible causes:
  1. If you have just added additional lights to your system, remove them and check if this solves the issue by turning the transformer back on via the app or power button on the device.
  2. Ensure there is no damage to the transformer and that it is not submerged in water.
  Check all the low-voltage wiring and light fixtures to make sure they are free of damage and possible short circuits.
  It is recommended not to attach more than a cumulative 160W (80%) of fixtures to the transformer based on the rating from the packaging.
  The low-voltage cable can consume up to 20% of the transformer capacity depending on the wire gauge and the total length of wire.

9. Schedules

• Use the Hubspace app to set up schedules for your transformer. See the app for details.
• Schedules can be set up to run every day or select days.
• Schedules can trigger based on time, sunrise, or sunset.

Troubleshooting Guide

Status of the LED light | Definition | Possible Cause

LED on | There is voltage output and the fixtures are on. |

LED off | There is no voltage output and the fixtures are off. |

LED flash | The loading is over limitation power or short circuit. | After troubleshooting, you need to press the button again, and the product will resume normal operation.

Note: When installing the fixture, the button LED light must be turned off to avoid the risk of electric shock.

Cable Selection Chart

12 VOLT

15 VOLT