TELESIN

Preface

Thank you for purchasing a Telesin product. Please read this user manual carefully before use.

Important Notes

• Please keep this user manual properly. When handing over the product to others, be sure to include this user manual.
• Pay attention to all warnings and follow all instructions in the user manual.
• After using the product in a seawater environment:
  • First, shake off the seawater from the selfie stick.
  • Then soak it in fresh water for 10 minutes.
  • After removing the product from fresh water, rinse it under gentle running tap water for 5 minutes.
  • After washing, wipe away any water droplets remaining on the surface with a soft, dry cloth and leave to dry. Do not dry with a hair dryer or any other heat source.
  • Store the product in a dry, well-ventilated location.
• Do not disassemble or damage this product. If it becomes deformed or damaged, stop using it immediately.
• Do not cover the product with items like towels or clothes during charging to prevent fire hazards.
• Do not drop the product or use it under high temperatures or short-circuit conditions.
• Keep this product out of reach of children.
• The product has passed the waterproof test of GB/T 4208–2017 and IEC 60529-2013 enclosure protection rating standard IP68. It is not recommended to use the product in extreme water environments or unknown liquid environments. Do not use it in hot springs or corrosive liquids.
• The product is only compatible with HERO 13/12/11/10/9/8 models.
• The waterproof depth of this product is 30 meters.

Warnings

Do not disassemble the product or replace the battery. If you suspect any problem with the product, contact the purchase platform for after-sales service.

Installation and Connection

1. Mount the action camera onto the selfie stick. If diving deeper than 10 meters, use a waterproof case (not included in the package).

   Diagram: Action camera being mounted onto the selfie stick.

2. Open the action camera remote connection interface and click "Connect with the remote". (The connection interface may vary by model, please refer to the user manual of the corresponding model).

   Diagram: Smartphone screen showing "Connect with THE REMOTE" and "Set The Remote to pairing mode."

3. Press and hold the power button ?️ on the selfie stick for 3 seconds to turn it on and automatically search for signals.

   Diagram: Selfie stick with buttons labeled. Power button indicated with a 3-second press.

4. Before the Bluetooth connection is established, all three indicator lights will light up and flash simultaneously.

   Diagram: Three indicator light icons showing simultaneous flashing (◐ ◐ ◐).

   Once connected successfully, the indicator light of the corresponding mode will light up.

   Diagram: Three indicator light icons showing one solid light (● ○ ○), representing a connected mode.

   (Complete the connection within 2 minutes, or the remote will automatically shut down).

Functions

Diagram: Remote control buttons labeled: Camera Mode, Power Button (?️), Shutter Button (⚪), Mode Button (M).

1. Switch Shooting Mode: Press the mode button M to switch between camera time-lapse ⏳, video ▶️, or photo ? modes. The status light of the corresponding mode will light up when switching.
2. Start Shooting: Press the shutter button ⚪ to start shooting, press the shutter button ⚪ again to end shooting.
3. Remote On/Off: Each time you press and hold the power button ?️, you can remotely turn the camera on or off synchronously.
4. Reset Pairing: Press and hold the mode button M for 3 seconds to reset pairing.

Indicator Light Instructions

Note: ● = remain on, ◐ = flash, ○ = not on.

Charging

Electric Charge State

Use the included charging cable for charging, connect the contact end to the charging port on the left side of the selfie stick, and connect the other end of the charging cable to a USB power source.

Charging time: 1 hour

Battery capacity: 80 mAh

Input: Pogo Pin Connector

Diagram: Correct (✔) and incorrect (❌) charging cable connections shown.

Note: Data measured by Telesin laboratory, slight deviations may occur due to changes in objective conditions.

Cautions and Disclaimer

FCC Caution

15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

IC Caution

This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions:

• (1) This device may not cause interference;
• (2) This device must accept any interference, including interference that may cause undesired operation of the device.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Disclaimer

Please read this statement carefully. By using this product, you will be deemed to have acknowledged and accepted it in full. Please check the product carefully before each use and do not use it if damaged or deformed. By using this product, you acknowledge and agree that you are fully responsible for your actions and the possible consequences of using this product. You undertake to use this product only for legitimate and lawful purposes. You understand and agree that Telesin Digital Co., Ltd ("Telesin") shall not be liable for any misuse, adverse effects, damages, injuries, penalties or other legal consequences arising directly or indirectly from the use of this product. The user should follow the precautions, including but not limited to those mentioned herein. To the extent Telesin reserves the right to interpret and modify this commitment within the limits of national laws and regulations.

*The warranty period for TELESIN products begins 6 months on the day you receive the product.

For more information, visit www.telesin.com.