MOUNT-IT! Installation Manual
SKU: MI-2757
FREESTANDING MONITOR ARM WITH HEIGHT ADJUSTMENT
Scan the QR code for product information, videos, and assembly assistance.
Important Safety Information
- Read the entire instruction manual before starting installation and assembly.
- CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.
- Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
- Safety gear and proper tools must be used. This product should only be installed by professionals.
- This product is designed to be installed on solid concrete walls, masonry walls, or wood stud walls.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact Mount-It! for a replacement.
- MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).
Mount and Accessories
Parts List
- A (x1): Stand Arm
- B (x1): Stand Base
- C (x4): M6x12 Bolt
- D (x1): 4mm Hex Wrench
- E (x1): 5mm Hex Wrench
Mounting Hardware
- M-A (x4): M4x12 Bolt
- M-B (x4): M5x12 Bolt
- M-C (x4): D5 Washer
Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used. Use the correct mounting hardware suitable for your installation.
CHOKING HAZARD: Package includes small parts. Not for children under 3 years. Adult supervision is required.
Missing Parts? Call us at (855) 925-5668 and we will ship replacement parts free of charge.
Dimensions & Weight Capacity
The monitor arm has the following approximate dimensions and adjustment ranges:
- Arm height adjustment: Minimum 12.4 inches to maximum 18.3 inches.
- Base dimensions: Approximately 4.6 inches wide by 3.9 inches deep.
- VESA plate to arm connection point: Approximately 10.2 inches.
- Monitor tilt adjustment: Forward +10°, Backward -15°.
- Monitor swivel adjustment: Left/Right +/- 25°.
- Monitor rotation: 90° for landscape or portrait orientation.
- Base to arm connection bolts: M6x12 (Part C).
- Monitor mounting bolts: M4x12 (Part M-A) and M5x12 (Part M-B), with D5 washers (Part M-C).
Rated weight capacity: 17.6 lbs (8 kg).
Caution: Ensure all mounting surfaces are capable of holding the weight of your mount. DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
Installation Steps
Step 1: Connect the Base and Arm
Connect the Stand Base (#B) to the bottom of the Stand Arm (#A) using the Bolts (#C) and tighten until secure using the 4mm Hex Wrench (#D).
Diagram shows the Stand Base (B) being attached to the Stand Arm (A) using Bolts (C) and tightened with the Hex Wrench (D).
Step 2: Attach the Monitor to the VESA Plate
Select the appropriate size mounting bolt (#M-A or M-B) and washer (#M-C) for your monitor's mounting holes. Verify the length of the VESA bolt is not too long. If you are unsure of the correct bolt size for your display, refer to your monitor user manual or contact the monitor manufacturer for sizing information.
Partially install the top 2 VESA bolts, leaving a gap of approximately 0.1 inches (3mm) between the monitor and the back of the bolt head.
Diagram illustrates attaching the monitor to the VESA plate using bolts (M-A or M-B) and washers (M-C). It includes visual indicators for checking bolt length: "Too long", "Too Short", and a representation of the correct fit.
Step 3: Attach the Monitor to the Arm
Hang the monitor onto the VESA Plate as shown. Secure the monitor to the bottom 2 bolt holes and tighten all bolts until secure. Monitor cables can be routed through the cable clip on the back of the arm.
Diagram shows the monitor being hung on the VESA plate and secured with bolts. A cable clip on the back of the arm is also indicated.
Step 4: Final Adjustments
To properly balance the arm with monitors mounted, adjust the spring tension using the supplied Allen Key (#E) as follows:
- First, position and firmly hold the arm horizontally as shown. Ask for assistance should you require it.
- If the arm drops, turn the adjustment screw clockwise until it stays in a horizontal position.
- If the arm rises, turn the adjustment screw counter-clockwise until it stays in a horizontal position.
CAUTION: To avoid damage to monitors or mount, always keep the arm in a horizontal position while making adjustments. Again, ask for assistance if required.
CAUTION: DO NOT over tighten the screws.
The monitor can be turned left to right +/- 25°, tilted forward or back +10°/-15°, and rotated 90° to alternate between landscape and portrait orientations.
Diagrams illustrate using the Allen Key (E) to adjust arm tension, showing the screw mechanism for when the arm drops or rises. It also depicts the monitor's range of motion for swivel, tilt, and rotation.
Support and Contact
Visit us at www.mount-it.com for product registration and warranty information.
Our US-based customer service team is standing by to answer any questions you have about your Mount-It! product.
Available by phone Monday - Friday from 8:00am to 4:00pm PST.
Chat live with an agent on our website!
[✉️] Email: support@mount-it.com
[?] Phone: (855) 925-5668
[?] Website Chat: www.mount-it.com
