MI-2752 1 Installation Instruction UNPACKING INSTRUCTIONS IMPORTANT SAFETY INFORMATION Carefully open the carton, remove contents and lay out on cardboard or other protective
Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage. Check package contents against the Supplied ...
MI-2752 Installation Instruction UNPACKING INSTRUCTIONS Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage. Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts. Carefully read all instructions before attempting installation. IMPORTANT SAFETY INFORMATION Install and operate this device with care. Please read this instruction before installation, and carefully follow all instructions contained herein. Use proper safety equipment during installation. Please call a quali ed installation contractor for help if you don't understand these directions or have any doubts about the safety of the installation. Do not use this product for any purpose or in any con guration not explicitly speci ed in this instruction. We hereby disclaims any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product. 1 Supplied Parts List (1)Pole-a (1)"C" Clamp-b (1)"C" Clamp Brace-c (1)Swivel Arm-d (2)VESA Plate-e (3)M5x14 Bolt-f (2)M8x12 Bolt-g (2)Nut-h (1)M10 Bolt-i (1)Support Plate-j (1)M10 Washer-k (1)Spring Washer-l (1)Grommet Base Plate-m (1)Wire Clip-n1 (4)Wire Clip-n2 (1)Allen Key-o (1)Wrench-p (8)M4x12 Thumb Bolt-q (8)M4x30 Bolt-r (8)M4 Spacer-s (1)Soft Pad-t1 (1)Soft Pad-t2 2 Step 1 Install the Pole to the Desktop Option A: Desk Clamp Install 1.Install the "C" Clamp Brace(c) to the Pole (a) using 3pcs M5x14 Bolts(f), and tighten using the Allen Key(o),see Figure 1. 2. Attach Soft Pad(t1) to the "C" Clamp Brace(c), see Figure 2. 3. Install the "C" Clamp(b) to the pole assembly according to the thickness of the desktop. The thickness can be changed to three positions. Connect it using 2pcs M8x12 Bolts(g), and tighten using the Allen Key(o). Tighten the "C" Clamp to the desktop using the plastic knob, see Figure 3. a c f t1 Figure 1 Figure 2 b Plastic Knob g o Figure 3 Option B: Grommet Base Install Existing Grommet Hole Installation If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount. f 1.Install the Grommet Base Plate(m) to the Pole(a) using 3pcs M5x14 Bolts(f), and tighten using the Allen Key(o), see Figure 4. 2. Attach Soft Pad(t2) to the Grommet Base Plate(m), see Figure 5. 3. Position the Pole(a) on the mounting surface and secure using the Support Plate (j), M10 Washer(k), Spring Washer(l) and M10 Bolt(i). Fasten the M10 Bolt using provided Wrench(p), see Figure 6. 3 a m Figure 4 t2 Figure 5 j k l i Figure 6 Step 1 Install the Pole to the Desktop Option C: Grommet Base Install a Self Drilled Grommet Hole Installation 1.Position the Pole(a) on the mounting surface and mark the center hole. Drill a 3/8" (10mm) diameter hole at the marked position through the mounting surface. 2. Install the Grommet Base Plate(m) to the Pole(a) using 3pcs M5x14 Bolts(f), and tighten using the Allen Key(o), see Figure 7. 3. Attach Soft Pad(t2) to the Grommet Base Plate(m), see Figure 8. 4. Position the Pole(a) on the mounting surface and secure using the Support Plate (j), M10 Washer(k), Spring Washer(l) and M10 Bolt(i). Fasten the M10 Bolt using provided Wrench(p), see Figure 9. m f Figure 7 t2 Figure 8 j k l i Figure 9 Step 2 Install Arm to the Pole Install Swivel Arm(d) to the Pole(a). Fasten the bolt with supplied Allen Key(o). Attach the Wire Clip(n1,n2) to the Pole(a) and Swivel Arm(d). d o n2 n1 4 Step 3 Attach the VESA Plate to the Monitor q s r For Monitor with Flat Back For Monitor with Curved or Recessed Back Step 4 Slide the Monitor onto the Head of Swivel Arm h Slide the monitor onto the head of Swivel Arm(d) as shown in the above diagram. Install the security Nut(h). Make sure the security nut is installed before you rotate the monitor. 5 Step 5 Make the Necessary Adjustments o o Fix the tilt angle Tighten the bolt with the supplied Allen Key(o) to fix the tilt angle. Ignore this step if monitors are level If one monitor is lower, remove the Nut(h) and turn the bolt counter-clockwise with supplied Allen key(o) to raise the monitor. Install the Nut(h) after the adjustment. Step 6 Manage the Wires and Store the Allen Keys on Wire Clip o n1 Use the supplied Allen Key(o) to make the necessary adjustments. Manage the wires and store the Allen keys(o) in Wire Clip(n1) for future use. Thank you for choosing our products! 6Adobe PDF library 10.01