Mount-It! Installation Instruction

Unpacking Instructions

Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.

Check package contents against the Supplied Parts List to assure that all components were received undamaged. Do not use damaged or defective parts.

Carefully read all instructions before attempting installation.

Important Safety Information

Install and operate this device with care. Please read this instruction before installation, and carefully follow all instructions contained herein. Use proper safety equipment during installation.

Please call a qualified installation contractor for help if you don't understand these directions or have any doubts about the safety of the installation.

Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. Mount-It! disclaims any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

Supplied Parts List

Parts:

(1) 48mm Pole-a
(1) Weighted Base-b
(1) Monitor Arm-c
(1) Plastic Cover-d
(1)M10 Bolt-e
(1)Support Plate-f
(1)M10 Washer-g
(1) Spring Washer-h
(2)M8x10 Bolt-i
(3)M6x29 Bolt-j
(1)Allen Key-k
(1)Wrench-l
(12)M4x12 Thumb Bolt-m
(12)M4x30 Bolt-n
(12)M4 Space-o
(2)Spare Cover-p

Tools Required: Phillips Screwdriver

Warning: This monitor desktop mount must be securely installed to the horizontal desk. If the mount is not properly installed it may fall, resulting in possible injury and/or damage.

Step 1: Mounting the base according to your requirement

The stand can be used with the weighted metal base or there is a desk attachment provided (as drawings on the bottom) allowing you to mount the stand on a desk. This is very simple to install and just requires a hole drilling (10mm diameter) in your desk and clamping with the bolt and large washer.

Option 1

Diagram shows the weighted base (b) attached to the pole (a) with a plastic cover (d).

Option 2

Diagram shows the pole (a) with plastic cover (d) being attached to a desk using bolts (e), washers (g, h), and a support plate (f).

Option 3

Diagram shows the weighted base (b) attached to the pole (a) with plastic cover (d), and bolts (j) securing it, with washers (f, g, h) and bolt (e) also shown.

Step 2: Install Monitor Arm to the Pole

Install monitor arm to the pole, please make sure the wire clip is in the downside. Fasten the M8x10 bolt(i) by screw driver.

Diagram shows the monitor arm (c) being attached to the pole (a) with bolt (i) and a wire clip.

Step 3: Mount the Monitor to VESA Plate

For Flat Back Monitor

Diagram shows a monitor being attached to the VESA plate (c) using thumb bolts (m).

For Curved Back Monitor

Diagram shows a monitor being attached to the VESA plate (c) using bolts (n) and spaces (o).

Step 4: Do the Necessary Adjustment

Level Adjustment

Use the Allen Key(k) to adjust the turning tension. Use the Wrench(l) to tighten the nut if the tilt angle can not be fixed.

Diagram shows Allen Key (k) being used to adjust tension on the monitor arm.

Center Monitor Adjustment

Turn the bolt counterclockwise to lower the center monitor, turn the bolt clockwise to raise the center monitor.

Diagram shows a bolt being turned to adjust the height of the center monitor.

Step 6: Manage the Wires

Diagram shows the monitor setup with wires managed through clips on the arm.

Thank you for choosing our products!

	Mount-It! MI-4752 / MI-4752WHT Full Motion Dual Monitor Desk Mount User Manual Comprehensive user manual for the Mount-It! MI-4752 and MI-4752WHT full motion dual monitor desk mounts. Includes assembly instructions, parts list, dimensions, weight capacity, and adjustment guides for optimal setup and use.
	Mount-It! MI-2752 Dual Monitor Desk Mount Installation Guide Comprehensive installation instructions for the Mount-It! MI-2752 dual monitor desk mount. Learn how to safely and securely attach your monitors to the desk using desk clamp or grommet base options.
	Mount-It! MI-2757 Freestanding Monitor Arm Installation Manual Comprehensive installation manual for the Mount-It! MI-2757 Freestanding Monitor Arm with Height Adjustment. Includes parts list, safety warnings, and step-by-step assembly instructions.
	MOUNT-IT! MI-3771W_G7, MI-3771B_G7 Tablet Stand Installation Guide Comprehensive installation instructions for the MOUNT-IT! MI-3771W_G7 and MI-3771B_G7 tablet stands. Learn how to assemble the stand, mount your tablet, and secure it to various countertop surfaces.
	MOUNT-IT! Heavy-Duty Under Desk / Wall CPU Mount Installation Manual This installation manual provides detailed instructions for mounting your MOUNT-IT! Heavy-Duty Under Desk / Wall CPU Mount. Learn how to safely install and adjust the mount for your computer, including options for desk, wood wall, and concrete wall installations. Includes parts list, dimensions, and support contact information.
	Mount-It! MI-303B TV Wall Mount Installation Guide Comprehensive installation instructions for the Mount-It! MI-303B TV wall mount. This guide covers unpacking, safety precautions, mounting the TV brackets to the TV, and attaching the wall plate to various wall types (brick, concrete, wood studs).
	MOUNT-IT! 2020 Product Catalog Explore the comprehensive 2020 Product Catalog from MOUNT-IT!, showcasing a wide range of mounting solutions and office furniture. This catalog features TV mounts, monitor mounts, ergonomic desks, laptop accessories, tablet solutions, and various office essentials designed to enhance productivity and comfort in any environment.
	MOUNT-IT! Tablet Wall Mount with Swing Arm Installation Manual Comprehensive installation manual for the MOUNT-IT! Tablet Wall Mount with Swing Arm (Models MI-3774B_G10, MI-3774W_G10). Includes parts list, safety warnings, dimensions, weight capacity, and detailed step-by-step assembly instructions for various wall types and tablet compatibility.