Outsunny Garden Table and Bench Set Assembly Instructions

Model: 84G-828V00 | Part Number: IN241200116V01_GL

Estimated Assembly Time: 1.5 Hours | Steps: 07 | Max Weight Capacity: 240kg

Important Information

Important: Retain for future reference. Read carefully.

This product is intended for domestic use only.

Use Tips

Place the set stably on a flat floor for optimal performance.
Install the furniture in a sheltered area, such as under an awning.
Keep away from open flames and heat sources.
Do not hang anything on the structure.
Do not exceed the maximum weight capacity (240kg).
Avoid staying on the furniture during storms or adverse weather conditions.
Cover the furniture with a suitable cover when not in use to protect it from the elements and prevent mold.

Precautions Before Assembly

Prepare a clean and dry assembly area.
Verify that the product is not damaged before starting.
Check that all parts and hardware are present.

Maintenance and Care

Clean the furniture with a soft, damp cloth.
Regularly remove any leaves or water collected on the fabric or surfaces.
Periodically inspect the furniture for any signs of wear or looseness.
Do not use the product if seat cloths, cushions, or tarpaulins appear aged or deteriorated. Contact customer service immediately in such cases.

Assembly Note

Caution: Be aware of the risk of pinching or cuts during assembly. Ensure all parts are connected before fully tightening bolts.

The manufacturer is not responsible for damages resulting from improper installation or weather-related issues.

Parts List

Identifier	Description	Quantity
A	Table Top Support/Frame	x2
B	Bench Frame	x2
C	Table Leg (Long)	x1
D	Table Leg (Short)	x2
E	Table Slat/Plank	x3
F	Bench Seat Support/Slat	x4
G	Bench Leg Support	x2
H	Bench Leg	x2
I	Bench Leg Support/Crossbar	x4

Hardware List

Identifier	Description	Quantity
1	M6.0*15 Screw	x12 (+1 spare)
2	M6.0*30 Screw	x8 (+1 spare)
3	M6.0*50 Screw	x4
4	M6.0*65 Screw	x12 (+1 spare)
5	M6.0*80 Screw	x16 (+1 spare)
6	Washer	x20
7	Allen Key	x1

Assembly Steps

General Note: Do not tighten bolts fully until all parts are connected.

Step 1: Assemble Bench Legs

Attach bench legs (H) to bench leg supports (G) using screws (4) and washers (6). Repeat for both bench legs.

Diagram Description: Shows two bench legs (H) being attached to two bench leg supports (G) with screws (4) and washers (6).

Step 2: Assemble Table Frame

Attach table supports (A) to table legs (C and D) using screws (1) and washers (6). Repeat for both sides of the table.

Diagram Description: Shows table supports (A) being attached to table legs (C, D) with screws (1) and washers (6).

Step 3: Attach Table Slats

Attach table slats (E) to the assembled table supports (A) using screws (2) and washers (6). Repeat for all three slats.

Diagram Description: Shows three table slats (E) being attached to the table frame assembly with screws (2) and washers (6).

Step 4: Assemble Bench Frame

Attach bench frames (B) to the assembled bench legs (from Step 1) using screws (5) and washers (6). Repeat for both bench frames.

Diagram Description: Shows bench frames (B) being attached to the bench leg assemblies with screws (5) and washers (6).

Step 5: Connect Table to Bench Frames

Connect the assembled table frame (from Step 2) to the bench frames (from Step 4) using screws (1) and washers (6). Repeat for both connections.

Diagram Description: Shows the table frame assembly being connected to the bench frame assemblies using screws (1) and washers (6).

Step 6: Attach Bench Leg Supports

Attach bench leg supports/crossbars (I) to the bench frames (B) using screws (5) and washers (6). Repeat for all four supports.

Diagram Description: Shows bench leg supports/crossbars (I) being attached to the bench frames (B) with screws (5) and washers (6).

Step 7: Final Table Slat Attachment

Attach the remaining table slats (E) to the table supports (A) using screws (1) and washers (6). Repeat for the remaining two slats.

Diagram Description: Shows the final table slats (E) being attached to the table frame assembly with screws (1) and washers (6). The final assembled product (table with benches) is shown.

Customer Support and Contact Information

If you have any questions, please contact our customer care center. Our contact details are below:

United States (US)

Phone: 001-877-644-9366

Email: customerservice@aosom.com

Imported by: Aosom LLC, 27150 SW Kinsman Rd, Wilsonville, OR 97070 USA. Made in China.

Canada (CA)

Phone: 416-792-6088

Email: customerservice@aosom.ca

Imported by: Aosom Canada Inc., 7270 Woodbine Avenue, Unit 307, Markham, Ontario Canada L3R 4B9. Made in China.

Germany (DE)

Phone: 0049-0(40)-88307530

Email: service@aosom.de

Importer/Manufacturer/REP: MH Handel GmbH, Wendenstraße 309, D-20537 Hamburg, Germany. Made in China.

Italy (IT)

Phone: 0039-0249471447

Email: clienti@aosom.it

Imported by/Manufacturer/REP: AOSOM Italy srl, Centro Direzionale Milanofiori, Strada 1 Palazzo F1, 20057 Assago (MI), Italy. Made in China.

Spain (ES)

Phone: 0034-931294512

Email: atencioncliente@aosom.es

Importer/Manufacturer/REP: SPANISH AOSOM, S.L., C/ROC GROS, N°15.08550, ELS HOSTALETS DE BALENYÀ, SPAIN. Made in China.

United Kingdom (UK)

Phone: 0044-800-240-4004

Email: enquiries@mhstar.co.uk

Importer Address: MH STAR UK LTD, Unit 27, Perivale Park, Horsenden lane South, Perivale, UB6 7RH. Made in China.

Portugal (PT)