Reyee RG-E6 Router Quick Installation Guide
This guide provides instructions for setting up your Reyee RG-E6 Router.
[email] For inquiries, suggestions, or product-related assistance, please email at techsupport@reyee.com.
[home] For comprehensive technical support, user manuals, and other helpful information, please visit https://www.reyee.com.
Frequently Asked Questions (FAQ)
Q1. What should I do if I fail to log in to the web interface?
Restart the router. Try logging in to your computer to obtain an IP address automatically. Make sure that the URL in the address bar of your browser is entered correctly. The default URL is http://192.168.110.1. Use either the browser to try again. We recommend using Google Chrome. Connect the router via an Ethernet cable connecting your computer and the router. Then, try it back in to establish a fresh connection.
Q2. What should I do if I cannot access the Internet?
Power off the modem and wait for 5 minutes. Then, power on the modem, and check the network connection. If your modem has multiple Ethernet ports, keep other ports disconnected or unused during this process. If the router is still unable to access the internet, by default, connecting it to the modem via WAN port, please contact your Internet Service Provider. If you use a modem for Internet service, power off your modem and router, and then remove the backup battery if it has one. If you have multiple Ethernet ports, you can connect the Ethernet port in the router to the WAN port of your router. Once Connected, proceed to Step 3 and 4. If you are unable to access the setup page, see Q1 in FAQ for further assistance.
Q3. What should I do if I forget the management password of the router?
If you haven't bound the router to the Reyee Router App and you are unable to log in using the Wi-Fi password, try restoring the router to factory defaults. Go to Settings > Advanced Management > Password.
Q4. Where should I place the router for better wireless coverage?
Do not place the router in a corner or inside a network enclosure. Avoid placing the router near objects that may obstruct signals. Place the router on a desktop, and keep the antennas vertical upwards.
Safety Information
[warning] Do not use or place the device if it is damaged. Do not use the device if doing so causes danger or interferes with other functions.
- Do not attempt to disassemble, repair, or modify the device. If you need services, then contact us.
- Do not place the device in a humid or wet environment.
- Keep the device away from heat sources, such as radiators or ovens.
- Ensure proper ventilation around the device.
- Handle the device with care. Do not drop or subject it to strong impacts.
- Do not use the device in an environment with a maximum distance of 30 cm between the radiator and your body.
- When using an un-mounted or incomplete power adapter, power cord, or battery, damage may occur to your device, shorten its lifespan, or cause fire hazards.
- This device is intended for indoor use only.
- Do not use the device in locations where the device may cause unwanted interference.
- Caution: Electrical shock hazard. Do not open the casing.
- This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
- Do not expose the equipment to rain or moisture.
- To reduce the risk of exposure to RF radiation, the device should be operated in a position that minimizes the potential for human contact during normal operation.
- Do not operate the device if it is not functioning properly.
- Protect the power cord from being stepped on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Use only power adapters, attachments, accessories supplied by the manufacturer.
- Users should install this equipment in accordance with the manufacturer's instructions.
- Users should use the power adapters, attachments, accessories supplied by the manufacturer.
- When using a cord or cable, ensure that it is properly connected to the apparatus and that the apparatus is properly connected to the power outlet.
- Caution: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
- Caution: Changes or modifications to this equipment not approved by the manufacturer could void the user's authority to operate the equipment.
Regulatory Compliance
FCC Compliance Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
ISED Compliance Statements
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
ISED Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
Cet équipement est conforme aux limites d'exposition aux radiations ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.
Packaging Contents
Check the box and all accessories after removing the packaging materials.
- 1 x Router
- 1 x Power Adapter
- 1 x User Manual
- 1 x Warranty Card
- 1 x Network Cable
- 1 x Sympathy Card
Setup Guide
1. Connect Your Router
Follow these steps to connect your router to the internet.
- If you use a modem for Internet access, power off your modem and remove the backup battery if it has one.
- If you have multiple Ethernet ports, you can connect the Ethernet port in the router to the WAN port of your router. Once Connected, proceed to Step 3 and 4.
The diagram illustrates the physical connection. Connect the modem's Ethernet port to the router's WAN port using an Ethernet cable. Connect the router's power adapter [power]. The router features ports labeled "2.5GE Port (WAN/LAN)" and "Gaming Port". After powering on the modem and waiting for it to restart, verify the router's System LED [led] turns solid blinking or solid on.
2. Set Up Your Router
Choose your preferred method to set up your Reyee Router.
Method 1: Via a Web Browser
- Connect your smartphone or computer to the router using a wired or wireless connection. For the wired connection, use an Ethernet cable [ethernet] to connect your computer to the router's LAN port.
- For the wireless connection, open Wi-Fi settings on your smartphone, and connect to the Wi-Fi network that starts with "SSID @Reyee-sXXXX" (where XXXX is a random number). The Wi-Fi password is on the label [label] at the bottom of the router.
- In the browser, enter the instruction displayed setup page to complete setup. If the setup page is not displayed, open a web browser, enter
192.168.110.1in the address bar.
This visual shows the web browser interface for setup. It displays a Wi-Fi icon [wifi], the router's SSID (e.g., "SSID @Reyee-sXXXX"), and the address bar showing "192.168.110.1", indicating the router's configuration page.
If you are unable to access the setup page, see Q1 in FAQ for further assistance.
Method 2: Via an App
Download the up-to-date Reyee Router app. Follow app instructions to complete setup.
Buttons for "Download on the App Store" and "GET IT ON Google Play" are shown, accompanied by a QR code for the Reyee Router app.
3. Add a Reyee Unit
Expand your network coverage by adding another Reyee unit for mesh networking.
- Set up the first Reyee router using Method 1 or Method 2.
- If possible, connect the WAN port of the second router to a LAN port of the first router using an Ethernet cable [ethernet]. (Follow Step 3)
- Connect the second router to power [power]. After the second router has powered on, its LED [led] will start blinking. Press the Mesh button [mesh-button] on the first router. After a few seconds, the LED [led] on the second router will start blinking. The router is linking to setup on the mesh connection between the two routers. (Follow Step 3)
- Power off the second router. Indicate it to the desired location and power it on. Make sure that the mesh connection between the two routers is successful.
If not, place the second router within 2 meters (6.56 ft) of the first router. (Follow Steps 3 and 4)
The diagram depicts two routers, labeled "first router" and "second router", both equipped with a "Mesh Button" [mesh-button]. It guides users to press the Mesh button on the first router after the second router powers on and its LED [led] blinks, to establish a mesh connection.
After the mesh network setup is successful, the Wi-Fi name and password of the second router will be the same as those of the first router.
Before creating a mesh network, make sure that the second router has not been configured before. If you are uncertain, restore the second router to factory defaults by pressing the reset button [reset-button] for more than 10 seconds until the System LED [led] at the top starts fast blinking. The router will restore to factory defaults and restart.
For more details, please visit https://www.reyee.com.
