Reyee RG-E6 Home Wi-Fi Router

1.3.1 Top View

Figure 1-1 Top View: A diagram showing the top view of the Reyee RG-E6 router. It features four antennas and the 'Reyee' logo. Markings indicate: 1 for the Game Turbo LED, 2 for the System LED, and 3 for the Reyee Mesh/Game Turbo button.

1.3.2 Back View

Figure 1-2 Back View: A diagram showing the back panel of the Reyee RG-E6 router. It displays ports and buttons labeled 1 through 6.

2.2.1 Temperature and Humidity

Appropriate temperature and humidity at the installation site are crucial for ensuring normal operation and prolonged service life of the router. High humidity can lead to poor insulation and electrical performance issues such as leakage. On the other hand, low humidity can cause shrinkage of insulation gaskets and looseness of fastening screws, which can generate static electricity and pose a risk to internal circuits, especially in dry climate environments. High temperatures can significantly impact the reliability and service life of the device by accelerating the aging process of insulation materials. The following table describes the temperature and humidity requirements.

2.2.2 Cleanliness

Dust poses a significant risk to the operational safety of the device. When indoor dust accumulates on the device, it can lead to electrostatic adsorption and result in poor contact. This not only affects the lifespan of the device but also increases the likelihood of communication failures. The risk of electrostatic adsorption increases when the indoor relative humidity is low.

The following table describes the requirements for the dust content and granularity.

In addition to dust, the device also has specific requirements regarding the presence of harmful gases such as hydrochloric acid sulfides in the air at the installation site. These gases can cause accelerated corrosion of metals and aging of certain components. The following table describes the specific limits for harmful gases including SO₂, H₂S, NO₂, NH₃, and Cl₂ in the installation site.

2.2.3 ESD Protection Requirements

This device is designed with rigorous anti-static procedures during circuit design. However, excessive static electricity can still cause damage to its circuit board. Static electricity in the communication network connected to the device mainly originates from two sources:

• Outdoor high-voltage transmission lines, lightning and other external electric fields; and
• Internal systems such as indoor flooring materials and overall structure of the device.

To prevent damage caused by static electricity, pay attention to the following:

• Keep the indoor installation environment clean and free of dust.
• Maintain appropriate temperature and humidity.

2.2.4 Anti-interference

Anti-interference measures primarily target electromagnetic and current interferences. The following requirements should be met to ensure effective mitigation of interference:

• Take effective measures to prevent interference from power grid to the power supply system.
• Keep the device away from the grounding facility or lightning and grounding facility of the power device as much as possible.
• Keep the device far away from high-frequency current devices such as high-power radio transmitting stations and radar launchers.

2.2.5 Checking the Mounting Workbench

Regardless of whether the device is installed on a desktop or wall, the following conditions must be met:

• The desktop or wall surface must be smooth and clean.
• The Ethernet cables must be in good condition.

2.3 Tools

? Note: The RG-E6 router is not shipped with a tool kit. You need to prepare a tool kit by yourself.

3.3.1 Installing the Router

Installing the router on a flat surface: The router can be placed on a horizontal surface, such as on a shelf or desktop.

Installing the router on a wall: Do not place the router in a place where it will be exposed to moisture or excessive heat. Keep the router away from devices with strong electromagnetic interference, such as Bluetooth devices, microwave ovens, or cordless phones. Generally, the router is placed on a horizontal surface, such as on a shelf or desktop. The router also can be mounted on the wall as shown in the following figure. The screw head should have a diameter ranging from 5mm to 8 mm (5 mm ≤ D ≤ 8 mm), with a maximum height of 3 mm. The distance between two screws should measure precisely 111.64 mm. The screw should have a minimum length of 20 mm, with a visible portion above the wall measuring at least 4.5 mm in order to withstand the weight of the router.

3.3.2 Connecting Cables

? Note: If you use a modem for Internet access, power off your modem and remove the backup battery if it has one. If you do not have a modem, you can connect the Ethernet port in the wall directly to the WAN port of your router. Once connected, proceed to follow steps 3 and 4.

Step 1: Connect the modem to the WAN port on the router using an Ethernet cable.

Step 2: Power on the modem and wait for it to restart.

Step 3: Connect the power adapter to the router.

Step 4: Verify the System LED on the top of the router until it turns slow blinking at a 2-second interval or solid on.

The diagram shows the 2.5GE Port (WAN/LAN) and Gaming Port on the router.

3.4 Bundling Cables

? Note:

• Bundle the cables in a visually pleasing way.
• Make sure that the twisted pair cables at the connectors have natural bends or bends of large radius.
• Do not bind twisted pair cables too tightly, as this may press the twisted pair cables and affect their service life and transmission performance.

Bundling steps:

1. Bundle the hanging part of the twisted pair cables using cable ties and route them to the WAN port of the device.
2. Fasten the twisted pair cables to the cable trough of the mounting bracket.
3. Extend the twisted pair cables under the device and route them in a straight line.

3.5 Verifying the Installation

• Verify that the device is firmly and reliably secured.
• Verify that the twisted pair cable matches the port type.
• Verify that cables are properly bundled.

4.2.1 Checking Before Power-on

Verify that the DC power cord connector of the device is in good condition, and that the device does not shake when the DC power adapter is connected to the DC power cord connector.

4.2.2 Checking After Power-on

• Verify that the LED status is normal.
• After the device is powered on, verify that the SSID can be successfully connected to by a smartphone or any other wireless device.

4.3 Troubleshooting Power Failures

The working status of the LED on the device indicates whether the device power supply system is malfunctioning. See 错误!未找到引用源。错误!未找到引用源。 for the description of the LED status. Perform the following checks in the case of any abnormality:

• Verify that the device is properly powered on.
• Verify that the Ethernet cable is correctly connected to the device.

? Note: If the device still cannot be powered on after the preceding check, please email us at techsupport@ireyee.com.

6.2.1 The LED Is Off After the Device Is Powered On

Verify that the supplied power adapter is connected properly, and that the Ethernet cable is connected properly.

6.2.2 The Ethernet Port Is Not Working After the Ethernet Cable Is Plugged In

Verify that the device at the other end of the Ethernet cable is working properly. Then, verify that the Ethernet cable is capable of providing the required data rate and is properly connected.

6.2.3 A Client Cannot Discover the SSID of the Router

1. Verify that the router is properly powered on.
2. Verify that the Ethernet port is correctly connected.
3. Verify that the router is correctly configured.
4. Move the client closer to the router.

6.2.4 A Client Cannot Discover the 5 GHz SSID of the Router

• Verify that a 5 GHz SSID is configured on the router.
• Verify that the router is compliant with the IEEE 802.3at standard.

1000BASE-T/100BASE-TX/10BASE-T Port

The 1000BASE-T/100BASE-TX/10BASE-T port is a 10/100/1000 Mbps auto-negotiation port that supports auto MDI/MDIX Crossover. Compliant with IEEE 802.3ab, the 1000BASE-T port requires Category 5e 100-ohm UTP or STP (recommended) with a maximum distance of 100 meters (328 feet). The 1000BASE-T port requires all four pairs of wires to be connected for data transmission. The following figure shows the four pairs of wires for the 1000BASE-T port.

Figure 7-1 1000BASE-T Twisted Pair Connections: Diagrams illustrating 1000BASE-T twisted pair connections for straight-through and crossover cables, showing connections between Switch ports (e.g., 1TP0+, 2TP0-) and their corresponding connections.

100BASE-TX/10BASE-T can be interconnected using cables of the preceding specifications. For 10 Mbps, the 100BASE-TX/10BASE-T port can be connected using 100-ohm Category 3, Category 4, and Category 5 cables; for 100 Mbps, the 100BASE-TX/10BASE-T port can be connected using 100-ohm Category 5 cables with a maximum connection distance of 100 meters. The following table shows 100BASE-TX/10BASE-T pin assignments.

• Google Docs
• Google Drive
• Download [pdf]



File Info : application/pdf, 21 Pages, 1.06MB

Document Document

Related Documents

	Reyee RG-EW3200GX PRO Wi-Fi 6 Mesh Router Quick Start Guide Quick start guide for the Reyee RG-EW3200GX PRO Wi-Fi 6 Mesh Router, detailing appearance, indicator lights, and setup procedures for single router and Reyee Mesh configurations.
	Reyee RG-E6 Router Quick Installation Guide: Setup, Mesh, and Troubleshooting Comprehensive guide to installing and setting up your Reyee RG-E6 WiFi 6 Router. Learn how to connect, configure via web or app, establish a mesh network, and understand LED indicators and buttons.
	Reyee RG-R4 Mesh Router User Manual: Setup and Configuration Comprehensive user manual for the Reyee RG-R4 AX1800 Smart WiFi 6 Mesh Router. Learn how to set up a single router or create a mesh network for extended Wi-Fi coverage.
	Reyee Mesh Routers: Frequently Asked Questions Comprehensive FAQ for Reyee Mesh Routers, covering setup, features, compatibility, and troubleshooting for WiFi 6 systems like the R6 model. Includes information on mesh networking, access point mode, parental controls, and maintenance.
	Reyee RG-REX12 Range Extender Quick Installation Guide This guide provides step-by-step instructions for setting up and installing the Reyee RG-REX12 Wi-Fi Range Extender. It covers powering on the device, connecting to different router types, relocating the extender for optimal signal strength, understanding LED indicators and button functions, accessing settings, and common troubleshooting questions.
	Reyee RG-RAP2200(F) Quick Installation Guide A comprehensive guide for installing and configuring the Reyee RG-RAP2200(F) Access Point. Includes packing list, device overview, LED indicators, installation steps, and network setup methods.
	Reyee RG-RAP52-OD Outdoor Access Point User Manual User manual for the Reyee RG-RAP52-OD Outdoor Access Point, detailing installation, network setup, and configuration procedures.
	Reyee RG-NBS3100-24GT4SFP-P 28-Port Gigabit Managed PoE Switch Installation Guide Installation guide for the Reyee RG-NBS3100-24GT4SFP-P, a 28-port Gigabit Layer 2 managed PoE switch. Covers package contents, hardware overview, installation steps, initial configuration, and safety information.