W814-68 Entertainment Center
Assembly Instructions
Important Safety Information
General Safety Guidelines:
- Always use proper tools.
- Follow assembly steps in order; do not skip any.
- Check all packing materials carefully for small parts. Contact the retailer if parts are missing. Do not use substitute parts.
- Periodically check that all connectors (bolts, screws, etc.) are tight.
- Keep instructions for future reference.
Glass/Mirror Handling: Be extremely careful when handling glass or mirrors, as severe injury may result if they break. Never handle large pieces of glass or mirrors by yourself.
Electrical Cords: When assembling products with electric cords (lamps, lights, etc.), always ensure the electrical cord is unplugged before assembly and be careful not to twist the electrical cord during assembly.
Assembly Load: Do not stand on lower shelves to assemble upper shelves; use a step ladder. Do not stand on tables (end tables, coffee tables, dinner tables), as they are not designed to support a person's weight. If assembly instructions state that two or more people are required, do not attempt by yourself as there is a risk of injury.
Liability: Ashley Furniture Industries, LLC disclaims any liability for damages or injuries which may occur due to failure to properly follow assembly instructions, properly assemble the product, or properly use the product.
Note: Your unit may look different in appearance from the one shown in the illustrations on this instruction sheet.
Parts List
| Part | Description | Quantity |
|---|---|---|
| A | Main Frame Panel | 1 |
| B | Top Panel | 1 |
| C | Side Panel | 1 |
| D | Base Panel | 1 |
| E | Shelf Panel | 1 |
| F | Back Panel | 1 |
| G | Vertical Divider | 2 |
| H | Back Panel Support | 1 |
| J | Drawer/Door Component | 1 |
| K | Drawer/Door Component | 1 |
| L | Support Bracket | 2 |
| M | 1/4" x 32mm Screw | 24 |
| N | Allen Wrench (M4) | 1 |
| P | Drawer Slide/Hinge Component | 20 |
| R | #8 x 38mm Screw | 2 |
| S | Anti-Tip Kit Component | 1 |
| T | Leveler Foot | 2 |
Note: Tools required but not included: [screwdriver].
Replacement Parts: Contact RTAParts@ashleyfurniture.com or call 1-844-966-0809.
Assembly Instructions
General Assembly Note: Unit should be assembled by two or more people. Do not tighten any bolts until all bolts have been started.
Step 1
Position the main frame panel (A).
[Diagram Description: Shows part A being oriented for assembly.]
Step 2
Attach part C to the base structure using 8x screws (M) and the Allen wrench (N). Attach part L using 2x screws (M) and the Allen wrench (N).
[Diagram Description: Shows attachment of C and L to the base using screws M and tool N. Indicates quantities x4 for C and x2 for L.]
Step 3
Attach parts D and E to the frame using 2x screws (R).
[Diagram Description: Shows attachment of D and E using screws R. Indicates quantity x2.]
Step 4
Attach part F to the frame using 6x screws (M) and the Allen wrench (N).
[Diagram Description: Shows attachment of F using screws M and tool N. Indicates quantity x2 for this connection.]
Step 5
Install vertical dividers (G) and back panel support (H) into their designated slots.
[Diagram Description: Shows G and H being inserted into the unit structure.]
Step 6
Attach the top panel (B) using 10x screws (M) and the Allen wrench (N).
[Diagram Description: Shows top panel B being attached with screws M and tool N. Indicates quantity x10.]
Step 7
Install drawers and doors (J, K) using 20x components (P). These components likely represent drawer slides or hinge mechanisms.
[Diagram Description: Shows installation of J and K using part P, with arrows indicating movement and attachment points.]
Step 8
The unit is now fully assembled.
[Diagram Description: Shows the completed entertainment center.]
Final Steps & Safety
Tipping Restraint Installation
WARNING: The included tipping restraint may reduce, but not eliminate, the risk of furniture tip-over. Follow the instructions provided with the restraint for proper installation.
Unit Leveling
If the unit is placed on an unlevel surface, place a leveler (T) underneath one foot until the unit is level. Break off any protruding segments of the leveler.
[Diagram Description: Shows a leveler (T) being placed under a unit foot and an arrow indicating to break off excess material.]
