TRUE FINE Dione 28 in. 6-Light Chandelier
Overview
The 'Overview' section presents a diagram illustrating the chandelier's components and their assembly order. It depicts the connection from the ceiling outlet box down to the fixture body. Key elements shown include:
- Ceiling Connection: Outlet box, Wire nuts (described as 'Smooth').
- Wiring: Ground wire (Green/Bare copper wire), White wire (Ribbed).
- Mounting Hardware: [GROUP A] and [GROUP B] wire groups, H. Mounting strap, G. Screw, F. Canopy, E. Canopy lock ring.
- Chandelier Structure: D. Fixture chain, C. Loop, B. Stem, Metal chain, A. Fixture body.
- Decorative Elements: Short bead string, Long bead string.
Assembly Instruction
- Pass the wire through Stem (B) and Loop (C), then screw Stem (B) to Fixture body (A).
- Install Long bead string, short bead string and metal chain to Fixture body (A). The metal chains are installed above, connecting the socket and loop. Short bead strings connect the two adjacent sockets. Long bead strings connect the socket and the middle position.
- Fix Mounting strap (H) to outlet box with Screw (G).
- Link Loop (C) and Canopy (F) by Fixture chain (D).
- Connect the wires according to the wiring instruction for details.
- Fix Canopy (F) to Mounting strap (H) with Canopy lock ring (E).
- Install the bulbs (not included).
Wiring Instruction
- Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
- Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
| [GROUP A]: Connect to Black House Wire | [GROUP B]: Connect to White House Wire |
|---|---|
| BLACK | WHITE |
| *PARALLEL WIRE (round & smooth) | *PARALLEL WIRE (square & ridged) |
| WHITE OR GREY WITH TRACER | WHITE OR GREY WITHOUT TRACER |
| BROWN, GOLD OR BLACK WITHOUT TRACER | BROWN, GOLD OR BLACK WITH TRACER |
- Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
- Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
- Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
- Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.
Product Specifications
- Input voltage: 120V
- Rated power: 60W MAX × 6
- Lamp socket: E12
- Cord Length: 7ft.
Product Packaging
- Fixture body × 1
- Metal chain × 6
- Loop × 1 & Fixture chain × 1
- Mounting strap × 1 Canopy × 1
- Long bead string × 6 & Short bead string × 6
- Screw × 2 & Wire nut × 3
- Lamp instruction × 1
Cleaning
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Safety Information
Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.
Contact Us
E-mail: service@24h-reply.com
Print in china
Digital Services, Technology and Consulting | Reply
