SignaLink™ USB Product Guide

This document can be used to find the SignaLink USB, Radio Cable, and Jumper Module part number that is needed for a given radio. Users can search this document for their radio model using their viewer's "Find" feature (CTRL-F), or simply scroll down to browse. Radios are organized alphabetically by manufacturer and listed in alpha-numeric order. If a radio isn't listed, Tigertronics should be contacted to confirm the part numbers that are needed.

Every effort has been made to insure that the information provided in this document is accurate. However, mistakes do sometimes happen, and it is simply not possible to be aware of the idiosyncrasies of every available radio. If there are any doubts or questions about the information provided here, or if the correct part numbers for a radio are uncertain, Tigertronics should be contacted before ordering.

Important Notes for Part Selection

• The SignaLink USB is always supplied with a radio cable and the part number shown determines which cable is provided. For example, SignaLink USB p/n “SLUSB6PM” includes radio cable p/n “SLCAB6PM”.
• When multiple cable options are available, the Data, Accy or other rear panel connections will generally be listed first since they are usually preferred over the Mic jack connection. If the SignaLink USB or Radio Cable part number is not noted as “DATA“, “ACCY”, “REAR”, or “PACKET”, then it is for use with the radio's Mic jack.
• If a Jumper Module part number is not listed for a radio or “Jumper Wires” are shown, then the SignaLink will need to be configured using the supplied push-in jumper wires.
• If “Contact us for cable wiring information” is displayed, an email should be sent through the Tigertronics Contact Form for assistance.
• Be sure to read any notes shown for a radio as these detail important radio requirements or restrictions.

ADI Radio Compatibility

ALINCO Radio Compatibility

ANYTONE Radio Compatibility

AZDEN Radio Compatibility

BAOFENG / BTECH Radio Compatibility

BRIDGECOM Radio Compatibility

COMMRADIO Radio Compatibility

CONNECT SYSTEMS Radio Compatibility

DRAKE Radio Compatibility

ELECRAFT Radio Compatibility

FLEX-RADIO Compatibility

ICOM Radio Compatibility

JETSTREAM Radio Compatibility

JRC Radio Compatibility

KENWOOD Radio Compatibility

KIRISUN Radio Compatibility

LAB599 Radio Compatibility

LEIXEN Radio Compatibility

LUITON Radio Compatibility

MIDLAND Radio Compatibility

MOTOROLA Radio Compatibility

POWERWERX Radio Compatibility

PUXING Radio Compatibility

QYT Radio Compatibility

RADIODDITY Radio Compatibility

RADIO SHACK Radio Compatibility

RAYTHEON Radio Compatibility

RETEVIS Radio Compatibility

SAINSONIC Radio Compatibility

SGC Radio Compatibility

TEN-TEC Radio Compatibility

TYT Radio Compatibility

WOUXUN Radio Compatibility

XIEGU Radio Compatibility

YAESU Radio Compatibility

YOU KITS Radio Compatibility

General Notes

1. This jack does NOT mute the microphone when it is in use. If the SignaLink is attached to this jack, the radio's Mic Gain control will need to be turned down, or the microphone disconnected to avoid a “hot” mic.
2. This jack is for HF use only. For VHF or UHF operation, the SignaLink will need to be attached to a different jack on the radio.
3. This jack is for FM use only. It does NOT support USB/LSB operation.
4. Requires Yaesu's CT-164 adapter to convert from the radio's 10-pin mini-DIN connector to a standard 6-pin mini-DIN. This adapter should be available from any authorized Yaesu dealer.
5. Requires Yaesu's CT-141 adapter to convert from the radio's 8-pin mini-DIN connector to a standard 6-pin mini-DIN. This adapter should be available from any authorized Yaesu dealer.
6. Requires Yaesu's CT-131 adapter. This adapter should be available from any authorized Yaesu dealer.
7. This radio provides differential / balanced audio on the External Speaker jack. An external isolation transformer must be used when connecting this audio output to the SignaLink to prevent damage to the radio.