Replacement Genie Intellicode Garage Door Remote

Product Specifications

• Model Number: RC-SM26-GN-1
• Battery Type: Built-in CR2032
• Work Voltage: 3.3V
• Support Frequency: 315mhz/390mhz
• Code Type: Intellicode 1, Intellicode 2

Confirm Garage Door Opener Type Base On The Below Pictures

Intellicode 1---1995 to Present

INTELLICODE® 2 - 2010 to present

Program the remote SM26-GN-1 with your opener directly. The remote comes from the factory, was setup BUTTON 1 = Intellicode 1, BUTTON 2/3 = Intellicode 2.

To Program The Remote to Intellicode 1 Openers From 1995 to Present

1. Start with your garage door closed. Locate the Learn Code Button and Learn Code Indicator LED on your opener's powerhead. (Fig 4)
2. Press and release the Learn Code Button, the Learn Code LED will blink rapidly. (Fig 4)
3. Press and release the remote button 1, the Learn Code LED will stay on (stops blinking). (Fig 5)
4. Press and release the same remote button again, the Learn Code LED will turn off. (Fig 5)
5. Press and release the same remote button again, the Intellicode 1 Door Opener will run. (Fig 5)

To Program The Remote to Intellicode 2 Openers From 2010 to Present

1. Press and hold the PROGRAM/SET button on the opener's powerhead for 2 seconds or until the round LED turns BLUE. When you release the button, the BLUE LED will go out and the opener's LONG LED will turn PURPLE. (Fig 6)
2. Press and release the Remote button 2 or 3. (Fig 7)
3. Press and release that same remote button. After releasing the button the second time, the LEDs will both be off. (Fig 7)
4. Press and release that same remote button, the Intellicode 2 Door Opener will run. (Fig 7)

Shift Remote button 2 or 3 to Intellicode 1 Mode:

1. Press and hold the remote button 2 or 3. A steady Green LED will be illuminated and after 10 seconds, a Red LED will also illuminate.
2. Release the button.
3. Press and release that same button again TWICE, the remote's LEDs will both turn off.
4. Press and release that same button again, the remote's Red LED will light while you press that button indicating it is now in Intellicode 1 mode.

Shift Remote Button 1 to Intellicode 2 Mode:

1. Press and hold the remote button 1. A steady RED LED will be illuminated and after 10 seconds, a GREEN LED will also illuminate.
2. Release the button.
3. Press and release that same button again TWICE, the remote's LEDs will both turn off.
4. Press and release that same button again, the remote's GREEN LED will light while you press that button indicating it is now in Intellicode 2 mode.

Replacing The Battery (Programming is not affected by battery replacement)

1. Remove the battery cover.
2. Slide the old battery toward the bottom of the remote and out.
3. Properly discard the old battery.
4. Slide a new (CR 2032) battery into position and install the Cover back on.

Lost or Stolen Remote, Erasing All Remotes

• For Intellicode 1 Opener type: Press and hold your garage door opener's learn button. The light above the button will turn on and shut off after 6 seconds. Once the light is no longer on, your garage door opener will be cleared of previous remote control connections.
• For Intellicode 2 Opener type: Press and hold your garage door opener's program/set button until the round LED turns on blue, then release it. Press and hold the Up(+) and Down(-) button at the same time, until both LED turn on blue and flashing, then goes off.

Warranty

This remote carries a one-year manufacturer's warranty against defects in workmanship or materials commencing from the purchase date of the remote. If any problems occur, please contact Genie for help.

Compliance Information: RoHS, FCC, CE. Made in China.