Genie GK-R Wireless Keypad Instructions

Keypad Overview

Activate keypad by opening battery compartment and pulling protective tab. Reinstall compartment door to begin programming.

Keypad LED Indicators:

• LED On: Keypad On
• LED Flashing: Keypad Flashing
• Keypad LED On: Keypad On
• Keypad LED Flashing: Keypad Flashing

Keypad LED's:

• Successful Entries: Keypad LED will flash each time a key is pressed and entry is accepted.
• Failed Entries: Keypad LED, PROGRAM key, and number pad back light will flash rapidly indicating a problem with programming or an invalid PIN entry. Wait 15 seconds until back lighting shuts off and enter a valid PIN or reset keypad to reprogram.
• Successful Program or Valid PIN: Keypad LED and PROGRAM key will flash slowly and number pad back light will remain on for 15 seconds.

Important Safety Information

WARNING: MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH.

• DO NOT install transmitter (keypad) unless the door operator’s safety device works as required by the door operator’s manual.
• Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts.
• Keep people clear of opening while door is moving.
• DO NOT allow children to play with the transmitter or door operator.

If safety reverse does not work properly:

• Close door then disconnect opener using the manual release handle.
• DO NOT use transmitter or door operator.
• Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.

Programming a PIN Number (STEP 1)

Program the keypad for the first time with a Personal Identification Number (PIN). This PIN must be 3 to 8 digits.

1. Ensure number pad back lighting is off.
2. Press 3-5-7 in sequence.
3. Press PROGRAM key. LED will blink once per second.
4. Enter a PIN number (3-8 digits).
5. Press PROGRAM key. LED will blink twice and shut off.

The keypad is now programmed with a PIN number and ready to program to the garage door opener(s). See STEP 2A to program 1 Opener. See STEP 2B PROGRAMMING FOR MULTIPLE OPENERS if using keypad to operate up to 3 doors. If LED did not blink twice and shut off, please see RESETTING THE KEYPAD (FACTORY DEFAULT) section.

Programming the Keypad to 1 Opener (STEP 2A)

Program the keypad with a Personal Identification Number (PIN) as described in step 1. Then follow these additional steps.

1. Ensure number pad back lighting is off.
2. Enter the PIN number on keypad.
3. Press the UP/DOWN key 3 to 4 times slowly until garage door opener operates.

This completes the programming of a single door. See STEP 3 SINGLE DOOR OPERATION for further instruction.

Putting Opener into Programming Mode:

Current Production Openers: Press and hold the program button until the round LED turns blue, then release. The round LED will go out and the long LED will begin flashing purple. Return to STEP 2A or 2B.

Openers manufactured between 1995 to 2011 and all external receivers: Press & release Learn Code button once. The red LED will begin to flash. Return to STEP 2A or 2B.

Note: The openers LEARN LED will time out in 30 seconds. Programming must be completed within 30 seconds.

Programming the Keypad for Multiple Openers (Up to 3) (STEP 2B)

Program the keypad with a Personal Identification Number (PIN) as described in step 1. Then follow these additional steps.

1. Ensure number pad back lighting is off.
2. Enter PIN as programmed in STEP 1.
3. Press PROGRAM key twice. LED will blink once per second.
4. Enter total number of openers that keypad will be operating. (2 or 3).
5. Press PROGRAM key once. LED will blink twice and shut off.

Note: Only one PIN number can be used. The keypad is now programmed with a PIN number and set up for multi opener operation. Keypad is now ready to program to multiple garage door openers. If LED did not blink twice and shut off, please see RESETTING THE KEYPAD (FACTORY DEFAULT) section.

Programming the Keypad to Multiple Openers (Up to 3):

1. Place desired garage door opener (1, 2, or 3) into PROGRAMMING MODE.
2. Ensure number pad back lighting is off.
3. Enter the PIN number on keypad.
4. Press the UP/DOWN key once.
5. Press the number of the desired door (1, 2 or 3).
6. Press the UP/DOWN key 3-4 times slowly until garage door opener operates.

Repeat steps 1 through 6 to program second and third openers. This completes programming of multiple doors. See STEP 3 MULTI-DOOR OPERATION for further instruction.

Operating the Keypad (STEP 3)

Single Door Operation:

1. Ensure number pad back lighting is off.
2. Enter PIN number.
3. Press the UP/DOWN key.
4. Opener will operate.

Multi-Door Operation:

1. Ensure number pad back lighting is off.
2. Enter PIN number.
3. Press the UP/DOWN key.
4. Press number key corresponding with desired door (1, 2, or 3).
5. Desired opener will operate.

Note: Keypad will remain active for 15 seconds after a successful entry is made. During this 15 seconds ANY key will operate the opener.

Mounting the Keypad (STEP 4)

Keypad MUST be mounted within sight of the garage door(s) at least 5 feet above floor and clear of any moving door parts.

1. Remove battery cover and batteries.
2. Drill a 3/32” pilot hole for the top mounting screw.
3. Install included screw into pilot hole, leaving 1/8” gap between the screw head and wall. Wall Screw 1/8" head gap
4. Hook the slotted mount on back of keypad over the screw.
5. Mark and drill a 3/32” pilot hole for the bottom screw and secure keypad to the wall. (Do not over-tighten).
6. Reinstall batteries.

Replacing Batteries

If the keypad back-lighting fails to operate, Batteries may require replacement. Programming will not be lost during battery change.

1. Remove battery cover and batteries.
2. Replace batteries with same type alkaline (AAA) and check for proper direction of (+) and (-) terminals.

Rechargeable batteries are NOT recommended.

Resetting the Keypad (Factory Default)

If the keypad has already been programmed or at any time the programming should be erased and started from the factory default, follow these steps.

1. Ensure that number pad back lighting is off.
2. Press and hold the PROGRAM and UP/DOWN Keys together for approximately 5 seconds.
3. The LED will flash twice and all lights will go out indicating the keypad has been reset.
4. Start at STEP 1 to program a new PIN number.

Additional (Optional) Programming

Changing an Existing PIN:

1. Enter current PIN
2. Press PROGRAM key once.
3. Enter new PIN.
4. Press PROGRAM key once.

The Original PIN will no longer operate keypad or opener.

Setting a Temporary PIN:

A temporary PIN allows temporary access to the garage by normally unauthorized personnel such as repairmen or neighbors.

1. Enter current PIN.
2. Press PROGRAM key 3 times.
3. Enter a temporary PIN (3 to 8 digits).
4. Press PROGRAM key once.

The Temporary PIN will operate garage door opener until the original PIN is used. Use of the original PIN will delete temporary PIN.

Troubleshooting & Support

For questions, comments or troubleshooting, contact The Genie Company at:

1 Door Drive, Mount Hope Ohio, 44660

or call 1-800-354-3643 or visit our website at: www.GenieCompany.com

FCC / IC Statement

FCC Part 15.21 Statement: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC / IC Statement: This device complies with FCC Part 15 and Industry Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.