Saxby Picco LED Spike Light Instruction Manual

Technical Data

Care and Safety

• Clean with a soft dry cloth.
• Do not use solvents or abrasive cleaners.
• Always switch off the power supply before maintenance. [? ⬇️]
• The LED module is not replaceable; the entire luminaire must be replaced when the LED reaches its end of life.

Important Warnings and Advice

• This is a Class 1 product and must be earthed.
• Installation must be performed by a competent and qualified electrician.
• Ensure all parts are present before installation.
• Install in accordance with IEE Wiring regulations and current Building Regulations.
• The mains plug must be situated indoors (e.g., house, garage, shed) to protect it from the elements.
• Switch off the mains supply before installing or maintaining this fitting. Ensure others cannot restore the electrical supply without your knowledge. [?]
• If in doubt, consult a qualified electrician.
• If replacing an existing fitting, carefully note the wire positions.
• This system contains non-replaceable parts and cannot be serviced. If damage occurs, the part should be scrapped.
• A terminal block is not included and may require advice from a qualified person for installation.
• Dispose of waste electrical products responsibly; recycle where facilities exist. [♻️]

Installation Guide

Layout Planning

• Plan the desired layout carefully, ensuring cables reach between the junction box, LED driver, and light fitting.
• Avoid locating cables in hazardous positions.
• Position cables and outdoor rated junction boxes away from areas where they may be cut, trapped, or damaged.
• The mains supply cable must have a minimum cross-sectional area of 1.0mm².
• Cables must be protected using suitable conduit or plastic trunking.

Mounting and Wiring

• Existing fittings must be completely removed before installation.
• Ensure the switch is turned off before installation.
• Seal screws and cable entry points to maintain the IP rating.
• The cable entry point should be at least 10cm from the ground surface when installing the spike.
• Decide on the luminaire's final position. An approved outdoor rated plug and socket, or an approved outdoor rated external terminal block, may be required.
• Cables to be in walls or concealed underground must be protected using suitable conduit or plastic trunking.
• Take care not to drill into any pipes or mains cables beneath the surface when preparing mounting holes. [⚠️]
• Ensure the ground is suitable for pushing the spike into and can support the luminaire. Do not install in very wet or boggy areas.
• Attach the spike to the fitting using the knob and tighten securely.
• Wire the unit as detailed in the wiring diagrams.
• Replace the fuse or circuit breaker and switch on the power. [⚡️ ✅]
• Your light is now ready for use.

Wiring Instructions

Wiring - Plug Connection

Alternatively, the product can be connected to a 3-pin [?] plug.

• The appliance must be connected to a 240 volts AC supply.
• The appliance can be fitted to a rewireable 3-pin plug fitted with a 3 amp fuse (approved to BS1362).
• If the fuse requires replacement, use only a 3 amp fuse approved to BS1362.
• If the mains plug is unsuitable or removed, dispose of the cut-off plug safely to prevent electric shock hazards.
• There is a danger of electric shock if the cut-off plug is inserted into any 13 amp socket outlet.

Wire colours in the mains lead:

• Blue: Neutral
• Green / Yellow: Earth
• Brown: Live

[Diagram Description: A 3-pin plug showing connections for Earth (Green/Yellow), Neutral (Blue), and Live (Brown). Includes a fuse holder (3 Amps) and a cord clamp.]

Wiring - Terminal Block Connection

If not fitting to a plug, the product must be wired to an IP68 outdoor rated terminal block (e.g., item 90131/90132 recommended).

Connect the wires from your existing light fitting to the connection block (not supplied) inside the product as follows:

[Diagram Description: A terminal block connection showing SUPPLY wires (Neutral, Earth, Switched Live) connecting to the LIGHT FITTING wires (Blue N, Green/Yellow, Brown L).]

Product Information

For further information, please visit: https://www.lighting-info.co.uk/95205

Document Version: V3 30/11/2022

UK Manufacturer: BH17 7BY

EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg

Website: www.saxbylighting.com

Product Image Description

The product is a black, modern outdoor spike light designed for garden or pathway illumination. It features an adjustable head to direct light. The base of the light has a spike for insertion into the ground.