VIVOHOME

NOTE:

To continuously improve its products, VIVOHOME reserves the right to modify this information without prior notification. For any questions during assembly, please watch the video on the product page for reference or contact customer service with any questions, comments, or concerns. Thank you for using VIVOHOME products in your home!

Thank You For Purchasing From VIVOHOME

MADE IN CHINA

IMPORTANT SAFETY INSTRUCTIONS

Your safety and the safety of others are very important. We have provided important safety information in this manual. Always read and obey all safety information.

This is the safety alert symbol: ⚠️

All safety information will follow the safety alert symbol and the word "DANGER" or "WARNING".

DANGER

WARNING

These words mean:

If you do not follow the instructions strictly, you may endanger your life or be seriously injured.

The safety information will inform you of the potential dangers associated with the incorrect use of the product, how to minimize the possibility of injury, and the possible consequences of not following the instructions.

PREPARING YOUR ICE MAKER FOR USE

When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliance.

• Do not operate this or any other appliance with a damaged cord. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent, or a similarly qualified person in order to avoid a hazard. This ice-maker must be positioned so that the plug is accessible. Connect to properly polarized outlets only. No other appliance should be plugged into the same outlet. Be sure that the plug is fully inserted into the electrical outlet.
• Do not run the power cord over carpeting or other heat insulators. Do not cover the cord. Keep the cord away from traffic areas, and do not submerge it in water.
• We do not recommend the use of an extension cord, as it may overheat and become a risk of fire. If you must use an extension cord, use a No. 14 AWG minimum size with a rating of no less than 1875 watts.
• Please unplug the ice maker before cleaning or performing any repairs or maintenance.
• Use with caution when electrical appliances are used near children.
• Do not use your ice-maker outdoors. Place the ice-maker away from direct sunlight and make sure that there is at least 4 inches of space between the back of your unit and wall. Keep a minimum distance of 4 inches on each side of your unit away from other items.
• Do not use liquids other than water to make the ice-cubes.
• Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or explosion.
• Do not tip over the machine.
• If the ice maker is brought in from outside in wintertime, give it a few hours to warm up to room temperature before plugging it in.

WARNING: This appliance must be grounded.

DANGER – Risk of fire or explosion. Flammable refrigerant used. Do not use mechanical devices to defrost the ice maker. Do not puncture refrigerant tubing. Repairs should only be conducted by trained service personnel.

CAUTION – Risk of fire or explosion. Flammable refrigerant used. Consult repair manual/Owner's guide before attempting to install or service this product. All safety precautions must be followed.

CAUTION – Risk of fire or explosion. Dispose of property in accordance with federal or local regulations. Flammable refrigerant used.

CAUTION – Risk of fire or explosion due to puncture of refrigerant tubing. Follow handling instructions carefully. Flammable refrigerant used.

The ice maker should be installed in accordance with the safety standard for Refrigeration Systems, ASHRAE15. The ice maker shall not be installed in corridors or hallways of public buildings.

If the unit has a problem and needs to be repaired or if parts need to be replaced, it must be repaired by factory authorized maintenance personnel to minimize the risk of ignition due to improper repairs.

WARNING: This appliance must be grounded.

WARNING: Fill with drinking water only.

IMPORTANT

The wires attached to this machine are colored according to the following code:

• [Green] or [Green with a yellow strip]: Grounding
• [White]: Neutral
• [Black]: Live

To avoid a hazard due to the instability of the appliance, the appliance must be placed on an even or flat surface.

GETTING TO KNOW YOUR UNIT

UNIT

Air Outlet

Cold Water Faucet (Located by the button near the operation panel)

Water Drain Cap

Smart Core for the Water Bottle

Button to Pop Up the Water Faucet

Operation Panel

Ice Cube Basket (Can be pulled out)

OPERATION PANEL

Water Dispensing Button

ICE FULL Indicator Light

Large Ice Cube Light

Medium Ice Cube Light

Small Ice Cube Light

SELECT Button (Use to select the desired size of the ice cube)

ON/OFF Button (Use to start or stop the unit)

POWER Indicator Light

WATER Indicator Light (No water remaining in the unit)

OPERATING PROCEDURES & MAINTENANCE

UNPACKING YOUR ICE MAKER

1. Remove the exterior and interior packaging. Check that ice scoop is included. If any parts are missing, please contact customer service.
2. Clean the interior with lukewarm water and a soft cloth. Take out and clean the ice basket.
3. Find a location for your ice maker that is protected from direct sunlight and other sources of heat (e.g., stoves, furnaces, radiators). Place the ice maker on a level surface. Make sure there are at least 4 inches of space between the back and sides of your ice maker and other objects, including the wall.
4. Allow one hour for the refrigerant fluid to settle before plugging in the ice maker.
5. The appliance must be positioned so that the plug is accessible.
6. Before placing the water bottle on the unit, make sure that the drain plug on the back is tightly fastened.
7. Hold the water bottle vertically and upside down (over the unit) and place the water bottle into the designated SMART CORE. Apply slight pressure to pierce the bottle cap with the spigot. This unit accepts two-, three-, or five-gallon water bottles with pierceable sealed caps.

[Diagram: Illustration of the ice maker with an arrow pointing down indicating to place the bottle vertically down.]

CONNECTING YOUR ICE MAKER

*Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, please call customer service.

DANGER

1. This unit should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which connects with standard three prong wall outlets to minimize the possibility of electric shock.
2. Plug your device into a dedicated, properly installed, grounded wall outlet. Under no circumstances should you cut or remove the third (ground) pin on the power cord. Any questions about power and/or grounding should be directed to a certified electrician.
3. This appliance requires a standard 110-120V, 60 Hz, 3-prong electrical outlet.

CLEANING AND MAINTAINING YOUR ICE MAKER

Before using your ice maker, it is strongly recommended to clean it thoroughly.

1. Take out the ice basket.
2. Clean the interior with diluted detergent, warm water, and a soft cloth.
3. Use the water to rinse the interior parts. Drain the water by unplugging the drain cap on the bottom of the front side.
4. The exterior of the ice maker should be cleaned regularly with a mild detergent solution and warm water.
5. Dry the interior and exterior with a clean soft cloth.
6. If the machine will not be used for an extended period of time, drain the water completely and dry the interior.

USING YOUR ICE MAKER

MAKING THE ICE -CUBE

1. Select the size of the ice cube by pressing the “SELECT" button. If the room temperature is lower than 60°F, it is recommended to select small or medium ice cubes in order to avoid the possibility of ice sticking together.
2. Press “POWER" on the control panel to begin the ice-making cycle.
3. The ice-making cycle lasts 6 to 12 minutes, depending on the selected size of the ice cube.
4. If the water pump cannot supply more water, the ice maker will stop automatically, and the "ADD WATER" Indicator will light up on the control panel. Please check the water bottle and replace it with a full bottle of water. Press the "POWER" button again to resume the ice-making cycle. Allow the refrigerant liquid inside the compressor to settle for at least 3 minutes before restarting.
5. When the ice basket is full, the "ICE" indicator on the control panel lights up and the ice maker automatically stops operating.

TROUBLESHOOTING

TECHNINCAL PARAMETERS & CIRCUIT DIAGRAM

ELECTRICAL DIAGRAM FOR ICE-MAKER

[Diagram: Electrical schematic for the ice maker, showing connections for power supply, operation PCB, main control PCB, compressor, water pump, fan motor, and various switches and sensors.]