VIVOHOME Automatic Ice Maker & Shaver Machine 33lbs/day

DESCRIPTION

The ice maker has the following parts:

• 1. Front top lid
• 2. Viewing semi-transparent window
• 3. Front cover
• 4. Fan cover
• 5. Control Panel
• 6. Take Shaved ice door
• 7. Back cover
• 8. Back cover cooling hole
• 9. Power Cord and Plug
• 10. Water inlet from tap

SPECIFICATIONS

• Daily Ice Output: 15kg/24h
• Ice Storage Capacity: 1kgs
• Water Reservoir Capacity: 1.7L
• Refrigerant: R290
• Ice Shape: Bullet
• Dimension: 310*400*420mm

BEFORE/FIRST USE OF YOUR ICE MAKER

1. During transportation, the incline angle of the cabinet should not be over 45°. Do not turn the Ice maker upside down, as this may damage the compressor and sealed system.
2. Remove all packing material and carefully check your ice maker to ensure it is in good condition and that there is no damage to the ice maker or power cord and plug.
3. The Ice maker should be placed horizontally on a level surface. To ensure proper ventilation for your Ice maker, allow 150mm of space at the top, the back, and on each side. Do not install the Ice maker near an oven, radiator, or any other heat source.
4. Before using the Ice maker for the first time, please wait 2 hours after positioning it, and keep the front lid open for at least 2 hours.
5. Ensure that the voltage indicated on the ice maker corresponds with the voltage in your home.
6. Pure water is not allowed to be used on this unit; spring water is recommended.
7. Please always keep the viewing window closed during ice making.

CONTROL PANEL OPERATION

OPERATING INSTRUCTIONS

Step 1. Shaved ice may melt, so it is strongly recommended that a drain hose at the bottom of the unit be connected. The steps are as follows:

Sketch for step 1 shows a drain pipe.

The water tank drain outlet is at the bottom of the machine.

Step 2. Open the lid, take out the ice basket and fill the water reservoir with water. Make sure the water is not over the bottom of the ice collecting tray. If you prefer to fill the water automatically, then insert the water pipe into the socket at the back of the unit.

STEPS TO HOOK IT UP TO A TAP

Step 3. Press the ICE button to turn the unit on. The ice maker begins to work. Note: For the first three cycles, the ice may be small and irregular in size, or even no ice.

Step 4. If the ADD WATER indicator lights up, please take out the basket, then add water as per step 1, then press the ICE button to restart the ice maker.

Step 5. If the ICE FULL indicator lights up, please take out the ice with the scoop. Note: When the ice basket is full, please remove the ice immediately. Do not allow the ice collecting tray to overfill.

Step 6. Press the SHAVED ICE button to shave ice. Note: Before pressing this button, please put enough ice into the shaved ice bowl and cover the bowl cap well.

Step 7. Press the ICE button to stop the machine.

Step 8. Put a tank below the unit, then pull the unit a little forward, pull the drain plug at the middle of the tank to drain water.

Step 9. If you want to take off the pipe, as sketched above, first take off the blue ring named as A (if any), then press the white ring (lock) at the outer side named as B, and at last take out the pipe.

CARING

1. Clean the inner liner, ice collecting tray, water box, ice shovel, and evaporator frequently. When cleaning, unplug the unit and remove the ice cubes. Use a diluted solution of water and vinegar to clean the inside and the outside surface of the Ice maker. Do not spray Ice maker with chemicals or diluted agents such as acids, gasoline, or oil. Rinse thoroughly before starting.
2. Keep ventilation openings in the appliance enclosure, or in the built-in structure, clear of obstruction. Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
3. To ensure the cleanliness of the ice cubes, water in the water reservoir is suggested to be replaced every 24 hours.
4. If the compressor stops for any reason such as water shortage, too much ice, power off, etc., do not start the system right away. Wait 3 minutes, and then re-start the Ice maker.
5. Always use fresh water before starting ice production, either at initial installation or after a long shut-off period.
6. This unit is for home use only, not for outdoor use. If it is necessary for use outside, please make sure the view window is closed.

SAFETY NOTICE

In order to avoid any accidents, please refer to the following operation:

1. Disconnect power before servicing.
2. Do not pull directly on the wire when plugging or unplugging the unit.
3. If ice is abnormal, please call the seller.
4. It is normal for the compressor and condenser surface to reach temperatures between 70°C and 90°C during operation, and surrounding areas may be hot. Please don't touch it.
5. Due to fast freezing, ice cubes may appear “Cloudy”. This is trapped air in the water, and it will not affect the quality or taste of ice.
6. When out of use, please open the drawer at least 2cm to allow for air circulation and avoid any metallic components becoming rusted.
7. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
8. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
9. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
10. WARNING: Fill with bottled or good quality tap water only. (Do not fill with fruit juices or other drink types).
11. WARNING – Keep the air vents on the sides of the machine unblocked at all times.
12. WARNING – Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
13. WARNING – Do not damage the refrigerant circuit.
14. WARNING – Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

TROUBLESHOOTING

1. Please note, if a power failure occurs due to disconnection of the power cord, or the off power button has been pushed off during an ice making cycle, small ice chips may form and lodge in the automatic shovel, causing it to jam. If this occurs, the ice chips may be removed by disconnecting the power cord and gently pushing the shovel to the rear of the cabinet and removing the ice chips, then restarting.
2. Please restart the ice maker by pressing Stop and then Start. If the Ice shovel does not push the ice into the ice collector after the formed ice drops from the evaporator finger while at the same time the 'ICE' light is on, check to see if the water tray is horizontal or balanced. If not, then adjust by pressing the Ice shovel lightly with your finger. Then re-start the Ice maker.

NOTE:

To continuously improve its products, VIVOHOME reserves the right to modify this information without prior notification.

For any questions during assembly, please watch the video in the product page for reference. Or contact customer service via support@vivohome.com with any questions, comments, or concerns. Thank you for using VIVOHOME products in your home!

Thank You For Purchasing From
VIVOHOME
MADE IN CHINA