Keilton 5-Key Battery Powered Wall Switch

Instructions

• Sensor ON/OFF: Works with wired PIR motion sensor.
• Dim Up
• Dim Down
• ON/OFF
• Scene Switch: Three scenes selected from App setting.

Installation Steps:

1. Install 1pc CR2032 battery by opening the back cover.
2. Press and hold the buttons ① and ④ together for over 2 seconds to enter pairing mode or achieve reset function. The switch can be scanned in the next 30 seconds.
3. In the Keilton App, navigate to the "Switch" page and click to add the switch.
4. Select the light or light group to be controlled by this switch.
5. Select 3 scenes to be controlled by this switch.

TIPS: This Bluetooth device is compatible with Keilton lighting control system only.

IMPORTANT: Battery model # CR2032. The battery can be used for 5 years based on the usage of twice a day.

Wall Surface Installation

1. Step 1: Pry up the cover of the remote controller with a flat screwdriver.
2. Step 2: Replace the battery with a new one.
3. Step 3: Attach the cover.

1. Step 1: Remove the cover plate carefully with scissors.
2. Step 2: Mark a position where you want to install.
3. Step 3: Drill two holes with a power drill.
4. Step 4: Attach the bracket with supplied self-tapping screws.
5. Step 5: Slide the remote controller into the bracket.
6. Step 6: Attach the wallplate.

How to Install Keilton APP?

Scan the QR code below for downloading the APP.

[App Store QR Code] [Google Play QR Code]

Download on the App Store

Get it on Google Play

How to Control Lights with a Phone?

Scan to download Keilton APP instruction.

[Keilton APP Instruction QR Code]

WARRANTY INFORMATION

Keilton warranties this product to be free of defects in materials and workmanship for a period of five (5) years. There are no obligations or liabilities on the part of Keilton for consequential damages arising out of, or in connection with, the use or performance of this product or other indirect damages with respect to loss of property, revenue or profit, or cost of removal, installation or reinstallation.

Contact: sales@litetrace.com

FCC Statement:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC STATEMENT:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

• (1) This device may not cause interference.
• (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes :

• (1) Cet appareil ne doit pas causer d'interférences.
• (2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer un fonctionnement indésirable de l'appareil.