Keilton WP1013 3-Key Battery Powered Wall Switch
WP1013 User Manual
Instructions
Follow these steps to operate the switch:
- Install 1pc CR2032 battery.
- Press button "ON/OFF" and "together" over 2 seconds to enter pairing mode and achieve reset function. This switch can be scanned in the next 30 seconds.
- In Keilton App "Switch" page, click to add the switch.
- Select the light/light group to be controlled by this switch.
TIPS: This Bluetooth device is compatible with Keilton lighting control system only.
Important Information
Battery model: CR2032. The battery can be used for 5 years based on the usage of twice a day.
Wall Surface Installation
Step 1: Pry up the cover of Remote Controller with a flat screw driver.
(Illustration shows a flathead screwdriver prying open the battery compartment cover of the remote controller.)
Step 2: Replace the battery with new one.
(Illustration shows the CR2032 battery being replaced in the remote controller.)
Step 3: Attach the cover.
(Illustration shows the battery compartment cover being reattached.)
Step 1: Remove the cover plate carefully with scissors.
(Illustration shows a cover plate being removed from a wall.)
Step 2: Mark a position you want to install.
(Illustration shows marking points on the wall for screw placement.)
Step 3: Drill two holes with power drill.
(Illustration shows drilling holes into the wall.)
Step 4: Attach the Bracket with supplied self-tapping screws.
(Illustration shows a mounting bracket being attached to the wall with screws.)
Step 5: Slide Remote Controller into the bracket.
(Illustration shows the remote controller being slid into the mounted bracket.)
Step 6: Attach the wallplate.
(Illustration shows a wallplate being attached over the installed switch.)
App Integration
How to Install Keilton APP?
Scan below QR code for downloading the APP.
How to Control Lights with a Phone?
Scan to download Keilton APP instruction
Warranty Information
Our company warranties this product to be free of defects in materials and workmanship for a period of five (5) years. There are no obligations or liabilities on the part of our company for consequential damages arising out of, or in connection with, the use or performance of this product or other indirect damages with respect to loss of property, revenue or profit, or cost of removal, installation or reinstallation.
Contact: sales@litetrace.com
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interférences.
(2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer un fonctionnement indésirable de l'appareil.
