RELIABILT Electronic Deadbolt with Keypad User Manual and Troubleshooting Guide

Questions?

For customer service, call 1-866-386-7941, 8:00 a.m. - 8:00 p.m., EST, Monday - Sunday. You can also contact us at partsplus@lowes.com.

Safety Information

Please read and understand this entire manual before attempting to assemble, operate or install the product.

Preparation

Before beginning installation, ensure all parts are present. Compare parts with the package contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Estimated assembly time: 40 - 60 minutes.

Care and Maintenance

To ensure a long-lasting finish: 1. Remove locks, or do not install locks, prior to painting your door. 2. Periodically clean with mild soap and a soft cloth only. Do not use abrasives or harsh chemicals and avoid sharp objects.

User Guide

Do not use any chemical liquid or lubricating oil with additives to clean the lock body. It will damage the surface or even the mainboard.

Unit Interface

Keypad and Interior Assembly Description

The electronic deadbolt features a keypad on the exterior and an assembly on the interior. The exterior keypad includes numbered buttons and a programming button. The interior assembly includes a turn-piece, battery compartment, and reset button.

• 1. Programming Button: Used for entering codes, clearing errors, setting functions, and locking the door.
• 2. Number Buttons: Used to enter user codes (4-10 digits in length).
• 3. Cylinder: Used to lock/unlock the lockset from outside.
• 4. Washer: Prevents water from permeating into the lockset.
• 5. Battery Lid: Slides to allow battery changes.
• 6. Battery Holder: Holds four AA (1.5 V) alkaline batteries.
• 7. R Button (Reset): Restores default settings.
• 8. Turn-piece: Used to lock/unlock the lockset from inside.

Operating Instructions

Keep the door open while programming to avoid accidental lockout. The lock contains one factory-preset user code and can store up to ten additional unique user codes. Codes can be added and deleted at any time. For first-time programming, use the factory default programming code. It is recommended to change the default programming code and default user code immediately after installation.

Operation Indicator Sounds and Lights

Default programming code (PC): 0000. Default user code (UC): 1234.

The lock will cease operation if unauthorized codes are entered over 5 times. The system will unfreeze after 45 seconds.

Programming Steps

1. Door Handing Identification Process

   The lock needs to learn if your door is right-handed or left-handed. To initiate: Enter PC ➔ 0 ➔ ✅.

   DO THIS FIRST

2. Change Programming Code

   To change the programming code: Enter PC ➔ 4 ➔ ✅ ➔ Enter New PC ➔ ✅.

3. Add New User Code

   To add a new user code: Enter PC ➔ 1 ➔ ✅ ➔ Enter New UC ➔ ✅.

   Note: Up to 10 user codes can be saved. User codes should be 4-10 digits in length.

   IMPORTANT: It is recommended that you replace the default Programming Code and default User Code with codes of your own.

4. Delete an Existing User Code

   To delete a user code: Enter PC ➔ 2 ➔ ✅ ➔ Enter the UC you want to delete ➔ ✅.

5. Delete All User Codes at Once

   To delete all user codes: Enter PC ➔ 3 ➔ ✅.

   Note: Auto-locking and keypad locking functions will be invalid when user codes are deleted. The lock can only be operated by key during that time.

6. Toggle Auto-Lock On/Off

   To toggle auto-lock: Enter PC ➔ 5 ➔ ✅.

   Note: The preset delay-time is 30 seconds. You can change the time by following instruction #7. Repeat these steps to cancel the auto-locking function.

7. Set Auto-Lock Time Delay

   To set auto-lock time delay: Enter PC ➔ 6 ➔ ✅ ➔ Enter Seconds (10-99) ➔ ✅.

   Note: 10-99 seconds delay-time available.

8. Toggle Mute On/Off

   To toggle mute: Enter PC ➔ 7 ➔ ✅.

   Note: Repeat these steps to turn beeper On/Off. LED illumination is still functioning when it's in mute, but there will be no warning alarms.

9. Enable/Disable All User Codes

   To enable/disable all user codes: Enter PC ➔ 8 ➔ ✅.

   Note: Auto-locking and keypad locking functions will be invalid when user codes are disabled. The lock can only be operated by key during this time. Repeat the steps to enable the user codes again.

10. Create a One-Time User Code

    To create a one-time user code (4-10 digits long): Enter PC ➔ 9 ➔ ✅ ➔ Enter One Time Code ➔ ✅.

    Note: The one-time user code will automatically cancel after it is used one time.

11. Restore Default Settings

    To restore default settings: Press the R button for more than 5 seconds until you hear 3 long beeps.

    Note: After restoring default settings, you must run the door handing identifying process (#1) again before programming any other functions.

Troubleshooting

Limited Lifetime Warranty

The Manufacturer extends a Limited Lifetime Mechanical and Finish Warranty to the original "User" of this product against defects in materials and workmanship as long as the User occupies the residential premises upon which the product was originally installed. Upon return of a defective product to the Manufacturer, the Manufacturer shall either replace, repair or refund the purchase price in exchange for the product. This warranty does not cover abused or misused products or those products used in commercial applications. No other warranties, express or implied, are made with respect to the product, including but not limited to any implied warranty of merchantability or fitness for a particular purpose. The Manufacturer DOES NOT authorize any person to create for it any obligation or liability in connection with the product. The Manufacturer's maximum liability hereunder is limited to the purchase price of the product, and in no event shall the company be liable for any consequential, indirect, incidental or special damages of any nature arising from the sale or use of this product, whether in contract, tort, strict liability or otherwise.