Installation & Assembly
Suggestion: To make the installation process easier and faster, we recommend that three people work together to install the Vanity Desk.
General Guidelines
Please read the following instructions carefully and use the product accordingly. Please keep this manual and hand it over when you transfer the product. This summary may not include every detail of all variations and considered steps. Please contact us when further information and help are needed.
Notes
- Product is intended for indoor use only. It must be assembled and used according to the instructions. The seller does not accept any responsibility for damage or injury resulting from improper assembly or use.
- Please avoid long-term exposure to humid environments to prevent mildew.
- During assembly, align all screws with the corresponding pre-drilled holes first and then tighten them one by one.
- Inspect the screws regularly. Screws may become loose during long-term use. If necessary, retighten them to ensure stability and security.
Warnings
- Children are not allowed to assemble the product. During assembly, keep any small part out of reach of children as they may be fatal if swallowed or inhaled.
- Children are not allowed to stand, climb or play on the product to avoid serious bodily injury by toppling.
- Keep plastic packing bags out of reach of children to avoid any potential danger, such as suffocation.
- Avoid sharp objects and corrosive chemicals to prevent damage to the product or bodily injury.
Accessories List
| Item | Description | Quantity |
|---|---|---|
| 1 | Long flat panel | x1 |
| 2 | Long flat panel | x1 |
| 3 | Vertical panel with multiple holes | x2 |
| 4 | Long flat panel | x1 |
| 5 | Vertical panel with one hole | x1 |
| 6 | Large rectangular mirror assembly | x1 |
| 7 | Short flat panel | x2 |
| 8 | Long flat panel | x1 |
| 9 | Long flat panel | x1 |
| 10 | Tall rectangular side panel (left) | x1 |
| 11 | Tall rectangular side panel (right) | x1 |
| 12 | Medium rectangular panel with drawer slide slots | x1 |
| 13 | Medium rectangular panel with drawer slide slots | x1 |
| 14 | Long connecting panel | x1 |
| 15 | Long connecting panel | x1 |
| 16 | Long connecting panel | x1 |
| 17 | Rectangular glass top panel | x1 |
| 18 | Small rectangular connector piece | x2 |
| 19 | Drawer front panel | x2 |
| 20 | Metal bracket for drawer slides | x4 |
| 21 | Drawer side panel (narrow) | x12 |
| 22 | Drawer side panel (narrow) | x12 |
| 23 | Drawer back panel | x15 |
| 24 | Drawer bottom panel | x15 |
| 25 | Drawer front panel | x12 |
| 26 | Drawer side panel (wide) | x3 |
| 27 | Drawer side panel (wide) | x3 |
| 28 | Drawer back panel | x3 |
| 29 | Square stool top | x1 |
| 30 | Stool leg/support | x2 |
| 31 | Stool leg/support | x2 |
| 32 | Stool connecting piece | x1 |
| A | Small screws (e.g., 3.5x12) | x60+5 |
| B | Medium screws (e.g., 3.5x14) | x67+5 |
| C | Long screws (e.g., 3.5x35) | x168+5 |
| D | Small screws (e.g., 4x1) | x4+1 |
| E | Medium screws (e.g., 3.5x35) | x60+5 |
| F | Long screws (e.g., 7x50) | x26+2 |
| G | Very long screws (e.g., 8x40) | x35+3 |
| H | Assorted light bulbs and mounting hardware (H2x12, H3x13) | x1 |
| I | Small circular caps | x1 |
| J | Small square metal plates | x5 |
| K | Light fixture bracket with screw | x1 |
| L | Cable clip/tie | x1 |
| M | Small metal brackets | x4 |
| N | Drawer slides (left/right, with CL/CR/DL/DR markings) | x15 |
| P | L-shaped metal brackets | x4 |
| Q | Small circular caps/covers | x12 |
| R | Screws with washers | x1 |
| S | Small square adhesive pads | x4 |
Assembly Steps
Step 1
Attach drawer slides labeled 'N CL' and 'N CR' to the inner sides of panels '10' and '11'. Use screws 'B' (total x12) and 'C' (total x28). Ensure the slides are oriented with the 'UP' indicator facing upwards.
Step 2
Attach drawer slides labeled 'N CL' and 'N CR' to the inner sides of panels '12' and '13'. Use screws 'B' (total x12) and 'C' (total x24). Ensure the slides are oriented with the 'UP' indicator facing upwards.
Step 3
Attach metal brackets '20' to panel '10' using screws 'B' (x6). Attach drawer front panel '19' to panel '10' using screws 'B' (x6).
Step 4
Connect panel '12' to panels '18' and '13' using screws 'B' (x6).
Step 5
Attach metal brackets '20' to panel '11' using screws 'B' (x6). Attach drawer front panel '19' to panel '11' using screws 'B' (x6).
Step 6
Connect panel '13' to panels '18' and '13' using screws 'B' (x6).
Step 7
Connect panels '10' and '11' to the main structure using long connecting panels '15' and '16', secured with screws 'F' (x8).
Step 8
Connect panels '11' and '12' to the main structure using long connecting panels '15' and '16', secured with screws 'B' (x2) and 'G' (x2).
Step 9
Connect the main desk structure using long connecting panels '14' and '16', secured with screws 'F' (x8) and 'G' (x2).
Step 10
Attach drawer slides labeled 'C', 'N CR', and 'N CL' to the assembled desk frame using screws 'C' (x8) and 'N' (x2).
Step 11
Attach panels '8' and '9' to the underside of the main top surface using screws 'G' (x8).
Step 12
Attach panels '7', '8', and '9' to the underside of the main top surface using screws 'C' (x24), 'J' (x4), and 'M' (x4).
Step 13
Attach panels '7' to the top surface using screws 'B' (x11).
Step 14
Connect the main desk structure using panels '10', '11', '12', '13', secured with screws 'B' (x11), 'G' (x10), and 'F' (x2).
Step 15
Assemble drawer components: Attach panels '1', '2', '3', '4', '5', '6' using screws 'B' (x12), 'C' (x4), 'G' (x1), 'F' (x4), 'J' (x1).
Step 16
Attach the mirror assembly '6' to the main desk structure using screws 'B' (x10) and 'G' (x6).
Step 17
Attach panel '11' to the side using screws 'D' (x4), 'K' (x1), and 'L' (x1).
Step 18
Assemble three drawers: Use parts '26', '27', '23', '24', '28' with hardware 'A' (x12), 'C' (x12), 'E' (x12), 'N' (x3).
Step 19
Assemble twelve drawers: Use parts '21', '22', '23', '24', '25' with hardware 'A' (x48), 'C' (x48), 'E' (x48), 'N' (x12).
Step 20
Insert the assembled drawers into the vanity desk.
Step 21
Attach lights (H) to the mirror frame using screws 'H2x12' (x4) and 'H3x13' (x1).
Step 22
Attach cable management 'R' and power components 'T', 'C' to the vanity.
Step 23
Assemble the stool base using parts '30', '31', '32' with hardware 'B' (x8), 'C' (x8), 'P' (x4), 'G' (x6).
Step 24
Attach the stool top '29' to the assembled stool base using screws 'C' (x8).
Step 25
Attach the stool base to the vanity using parts '30', '31', '32' with hardware 'C' (x8) and 'P' (x4).
Step 26
Attach the stool (part '30') to the vanity using parts 'Q' (x12) and 'S' (x4).
Step 27
Secure the mirror assembly '6' to the vanity using part 'I' (x1) and 'R' (x1).
