Mi True Wireless Earphones 2 Basic User Manual

Read this manual carefully before use, and retain it for future reference.

Product Overview

The product consists of a charging case and two earphones.

Charging Case

• Indicator Light ?: Shows charging status and battery level.
• Charging Port ?: USB Type-C port for charging the case.

Earphones

• Secondary Microphone ?: Used for calls and noise reduction.
• Touch Area ?: For controlling music playback, calls, and voice assistant.
• Indicator Light ?: Shows connection and charging status.
• Primary Microphone ?: Used for calls and voice input.

Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.

Instructions

Charging

Charging the Earphones

When the earphones are placed in the charging case, they will automatically start charging.

Charging the Charging Case

The indicator light of the charging case is white during charging and goes off once it is fully charged.

Checking Battery Level

Checking the Battery Level of the Earphones

After connecting the earphones to a phone, you can check the earphones' battery level on the phone's status bar. Note: The phone's status bar usually displays the battery level of the earphone with the lowest battery level. This feature may not be supported by all phones.

Checking the Battery Level of the Charging Case

Open the lid of the charging case, or place the earphones into the charging case:

• When the indicator light of the charging case stays lit for 5 seconds, it means the battery is sufficient.
• The indicator of the charging case is blinking white, which indicates that the battery level of the charging case is low. Please charge it immediately.

Checking the Battery Level with a Mi Phone

After successfully connecting to a Mi phone, place the earphones into the charging case and close its lid. Ensure the Bluetooth function is enabled on your Mi phone. Hold your phone close to the charging case, then open the case's lid. A notification will appear on the phone, allowing you to check the battery level of the earphones and the charging case.

Note: When checking the battery level on your phone, please update your Mi phone to the latest stable version. This feature is currently only supported by some Mi phones.

Turning On

When opening the charging case, the earphones will automatically turn on. For first-time use, place the earphones in the charging case and close the lid to activate them.

Operation

Sleep Mode

Place the earphones back into the charging case and close the lid. The earphones will disconnect and go into sleep mode automatically.

Wearing

Take the earphones out of the charging case and insert them into your ears according to the left (L) and right (R) marks. After using the earphones, place them back into the charging case to extend their lifespan and prevent loss.

Connecting

Connecting the Earphones to a New Device

1. Place the earphones into the charging case, press and hold the touch area of either earphone for 3 seconds. The indicator of the earphones will blink white, indicating they are waiting for a connection.
2. Enable your device's Bluetooth, then locate and connect to "Mi TW Earphones 2 Basic". If a passcode is requested, enter "0000".

Connecting the Earphones with a Mi Phone

Place the earphones into the charging case and close its lid. Make sure the Bluetooth function is enabled on your Mi phone. Hold your phone close to the charging case, then open the case's lid. Follow the on-screen instructions of the phone to connect to the earphones.

Note: The fast connection feature is currently only supported by some Mi phones. Please update your Mi phone to the latest stable version.

Connection Interrupted

When your device is out of wireless range of the earphones or its Bluetooth function is disabled, the earphones will automatically enter the awaiting connection mode. If the earphones are not connected to any device within five minutes, they will enter sleep mode.

Automatic Connection

When the earphones are in the charging case, opening the lid will automatically connect the earphones to the most recently used Bluetooth device. If the earphones are not connected to any device within five minutes, they will enter sleep mode.

Note: If the earphones cannot automatically connect to a device, you will need to manually connect them via the device's Bluetooth settings.

Function Overview

Incoming Calls

Gently tap either one of the earphones twice: Answer/End calls.

Music and Voice Assistant

• While wearing both earphones:
  • Gently tap the right (R) earphone twice: Play/Pause music.
  • Gently tap the left (L) earphone twice: Access the voice assistant.
• Taking out an earphone: Music pauses automatically.
• While wearing one earphone: Gently tap the earphone twice: Play/Pause music.

Notes

• The voice assistant function can only be used if your device supports it and has granted permission.
• When using only the left earphone, place the right earphone into the charging case and close the lid.

Clearing Connection History

1. Place the left and the right earphone into the charging case.
2. Simultaneously press and hold the touch areas of the left and the right earphones for seven seconds, then release the touch areas once the indicators of the earphones light up in white.
3. The earphones have been reset, and the connection history has been cleared. The indicators of the earphones blink white, and they are waiting for a connection.

Due to the connection characteristics of the Bluetooth signal, in dense environments with 2.4 GHz electromagnetic signal interferences, there may be occasional disconnects or no sound.

Specifications

Safety and Compliance

Safety Caution

• Do not expose batteries or battery packs to excessive heat such as sunshine, fire, or the like.
• Replacement of a battery with an incorrect type can defeat a safeguard (such as catching fire, explosion, leakage of corrosive electrolyte etc).
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
• Risk of explosion if battery is replaced by an incorrect type.
• Dispose of used batteries according to the instructions.
• The product operation maximum ambient temperature is 40°C.

WEEE Information

All products bearing the ♻️ symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

EU Declaration of Conformity

Hereby, Tiinlab declares that the radio equipment type TWSEJ08WM is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.mi.com/global/service/support/declaration.html.

FCC and IC Compliance

To prevent possible hearing damage, do not listen at high volume levels for long periods.

The symbol ⚡ indicates DC voltage.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

The device is too small to bear the label information, and this label content is listed on the package and user manual. The marking information is located at the bottom of the apparatus.

• FCC ID: 2ASDITWSEJ08WM
• IC: 24662-TWSEJ08WM
• HVIN: V7
• CAN ICES-3(B)/NMB-3(B)

Legal and Manufacturer Information

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Xiaomi Inc. is under license. Other trademarks and trade names are those of their respective owners.

Manufactured for: Xiaomi Communications Co., Ltd.

Manufactured by: Tiinlab Acoustic Technology Limited (a Mi Ecosystem company)

Address: Tianliao Building 1403, Tianliao Industrial Area A, Taoyuan Street, Nanshan District, Shenzhen 518055, China

For further information, please go to www.mi.com.