Mi True Wireless Earphones 2 Basic User Manual

Introduction

The Mi True Wireless Earphones 2 Basic user manual provides a comprehensive guide to using the product. Before using the earphones, please read this manual carefully to ensure you understand all features. The manual includes product overview, charging, powering on, wearing, pairing, and operation. It also covers specifications, safety warnings, and WEEE directive information. Detailed instructions are provided for charging the earphones and the charging case, checking battery levels, connecting the earphones to a device, and resetting the earphones. The operation section explains how to answer and end calls, play or pause music, and access the voice assistant. Please note that the voice assistant function is only available if your device supports it. The manual also includes safety warnings to prevent potential negative consequences for the environment and human health. Overall, this user manual is an essential guide for users of the Mi True Wireless Earphones 2 Basic.

Product Overview

Read this manual carefully before use and keep it for future reference.

Charging Case

A diagram shows the charging case with an 'Indicator Light' and a 'Charging Port'.

Earphones

A diagram illustrates an earbud, highlighting the 'Secondary Microphone', 'Touch Area', 'Indicator Light', and 'Primary Microphone'.

Illustrations of the product, accessories, and user interface in the user manual are for informational purposes only. The actual product and features may vary due to product improvements.

Instructions

Charging

Charging the Earphones

When the earphones are placed in the charging case, they will automatically start charging.

Charging the Charging Case

During charging, the indicator light of the charging case glows white and turns off when fully charged.

Checking Battery Level

Checking Earphone Battery Level

After connecting the earphones to your phone, you can check the earphone battery level on the phone's status bar. Note: The phone's status bar always displays the battery level of the earphone with the lowest battery level. This feature is not supported by some phones.

Checking Charging Case Battery Level

Open the charging case lid or place the earphones into the charging case:

• When the charging case indicator light glows for 5 seconds, it means the battery is sufficient.
• The charging case indicator light flashes white, indicating that the case battery level is low. Please charge it immediately.

Checking Battery Level via Mi Phone

After successfully connecting to your phone, place the earphones in the charging case and close its lid. Ensure Bluetooth is enabled on your Mi phone. Bring the phone close to the charging case, then open the case lid. Follow the on-screen instructions on your phone to check the battery level of the earphones and the charging case. Note: When checking the battery level on your phone, update your Mi phone to the latest stable version. This feature is currently supported only by some Mi phones.

Powering On

When the charging case is opened, the earphones will power on automatically. Note: For the first use, place the earphones in the charging case and close the lid to activate them.

Sleep Mode

Place the earphones back into the charging case and close the lid; the earphones will disconnect and automatically enter sleep mode.

Wearing

Remove the earphones from the charging case and insert them into your ears according to the 'L' (left) and 'R' (right) markings. Note: After use, place the earphones back into the charging case. This will extend their lifespan and help prevent loss.

Connecting

Connecting Earphones to a New Device

1. Place the earphones in the charging case, press and hold the touch area of one earphone for 3 seconds. The earphone indicator light flashes white, and the earphones are waiting for connection.
2. Turn on the device's Bluetooth, then find and connect to "Mi TW Earphones 2 Basic". If a password is required, enter "0000".

Connecting Earphones to a Mi Phone

Place the earphones in the charging case and close its lid. Ensure Bluetooth is enabled on your Mi phone. Bring the phone close to the charging case, then open the case lid. Follow the on-screen instructions on your phone to connect to the earphones. Note: The quick connection feature is currently supported only by some Mi phones; update your Mi phone to the latest stable version.

Connection Interruption

If the device is out of the earphones' wireless range or its Bluetooth function is turned off, the earphones will automatically enter connection standby mode. If the earphones are not connected to any device within five minutes, they will enter sleep mode.

Automatic Connection

When the earphones are in the charging case, opening the charging case lid will automatically connect the earphones to the last used Bluetooth device. If the earphones are not connected to any device within five minutes, they will enter sleep mode. Note: If the earphones cannot automatically connect to a device, you will need to manually connect the earphones to the desired device via the device's Bluetooth settings.

Due to the characteristics of Bluetooth signal connection, in environments with dense 2.4 GHz electromagnetic interference, occasional disconnections or audio loss may occur.

Clearing Connection History

1. Place the left and right earphones in the charging case.
2. Simultaneously press and hold the touch areas of the left and right earphones for seven seconds, then release the touch areas when the earphone indicators glow white.
3. The earphones have been reset, and the connection history has been cleared. The earphone indicators flash white, and the earphones are waiting for connection.

Function Overview

Incoming Calls

Gently double-tap one of the earphones to answer/end calls.

Music and Voice Assistant

While wearing both earphones:

• Gently double-tap the right (R) earphone: Play/pause music.
• Gently double-tap the left (L) earphone: Access the voice assistant.

Removing an earphone: Pauses music. While wearing a single earphone: Gently double-tap the earphone to play/pause music.

Notes:

• The voice assistant function can only be used if your device supports it, and this function requires permission on the device.
• If you are only using the left earphone, place the right earphone in the charging case and close the lid.

Specifications

• Model: TWSEJ08WM
• Net Weight: 48 g
• Input: 5 V 1A
• Charging Port: Type C
• Impedance: 32 Ω
• Charging Time: Approx. 1.5h
• Wireless Connection: Bluetooth 5.0
• Bluetooth Profiles: BLE / HFP / HSP / A2DP / AVRCP
• Supported Audio Codecs: SBC / AAC
• Wireless Range: 10 m (open space without obstacles)
• Earphone Battery Life (Standalone): Approx. 5 hours
• Total Battery Life (with charging case): Approx. 20 hours
• Bluetooth Operating Frequency: 2402–2480 MHz (for EU)
• Maximum Transmission Power for BT: 10 dBm (for EU)
• Maximum Transmission Power for BLE: 10 dBm (for EU)

WEEE Information

Products marked with this symbol are waste electrical and electronic equipment (WEEE, Directive 2012/19/EU), which should not be mixed with unsorted household waste. To protect human health and the environment, please hand over waste equipment to a designated collection point for recycling of waste electrical and electronic equipment, designated by the government or local authorities. Proper disposal and recycling will help prevent potential negative impacts on the environment and human health. For more information on the location and terms of use of such collection points, please contact the installer or local authorities.

CE mark: Tiinlab hereby declares that the radio equipment type TWSEJ08WM complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.mi.com/global/service/support/declaration.html

Safety Precautions

• Do not expose batteries or battery packs to excessive heat, such as sunlight, fire, etc.
• Replacing the battery with an incorrect type may bypass a safeguard (e.g., in case of fire, explosion, corrosive electrolyte leakage, etc.).
• Disposing of a battery in a fire or hot oven, or mechanically crushing or cutting a battery, may result in an explosion.
• Leaving a battery in an extremely high-temperature environment may result in an explosion or leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure may result in an explosion or leakage of flammable liquid or gas.
• Replacing the battery with an incorrect type may result in an explosion.
• Dispose of used batteries according to the instructions.
• The maximum ambient temperature during product operation is 40 ° C.
• ? [Hearing protection symbol]
• ⚡ [DC voltage symbol]

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

The device is too small to contain the label information; label content is also provided on packaging and in the user manual. Marking information is located on the bottom of the apparatus.

Frequently Asked Questions (FAQs)

How long does it take to charge the earphones?

A full charge of the earphones, when completely discharged, takes about 1 hour.

Are they compatible with iPhone X?

Yes, are the earphones Bluetooth?

Are they compatible with Windows PC? Used for Zoom calls on a computer?

Yes.

Do they have noise reduction?

Unfortunately no, but they are still great for the price.

Do these earbuds work with Apple/iOS devices?

Yes.

Charger USB C?

No.

Are the earbuds disposable?

No.

Are the Xiaomi Mi True Wireless Earphones 2 Basic basic?

The Xiaomi Mi True Wireless 2 Basic wireless earphones are among the cheapest true wireless earphones you can buy and come with many compromises. The earphones are well-made, feature touch controls, and are incredibly affordable, but they simply don't sound good.

How long do Mi True Wireless Earphones 2 Basic earbuds last?

With the Redmi AirDots 2 charging case, they have a declared battery life of 12 hours with a 300 mAh battery. The case uses a Micro-USB port for charging. The earbuds themselves charge in about 1.5 hours, and the case in about 2 hours.

Do Xiaomi earbuds work with other phones?

The wireless earphones support all Android, iOS, and Windows devices with Bluetooth compatibility.

How to check the battery of Mi True Wireless Earphones 2 Basic?

After connecting the earphones to your phone, you can check the earphone battery level on the phone's status bar. To check the charging case battery status, open the charging case lid or press the function button if the lid is closed.

Can iPhone use Xiaomi earbuds?

Yes.

Mi True Wireless 2 earphones are compatible with Android and iOS devices and feature smart in-ear detection sensors, allowing them to play or pause based on when you wear them.

How to charge the true wireless earbuds using the charging case?

To charge the case, connect it to a compatible USB power outlet using the provided charging cable. During charging, the LED indicator on the front of the charging case will flash red, and after a full charge, it will glow solid red.

Why do my earphones keep dying?

Pulling or yanking the earphone cables when disconnecting them. Leaving earphones dangling from tables, sofas, beds, and other surfaces. Sleeping with earbuds, exposing them to twisting. Wearing earphones without the case or putting them in pockets or bags.

Is Bluetooth more secure than Wi-Fi?

Wi-Fi is better suited for handling networks on a larger scale, as it allows for faster connection, better range from the base station, and better wireless network security (if configured correctly) than Bluetooth.

How do I know when my true wireless earbuds are charged?

The earbud indicator changes to red after 10 seconds and turns off when the earbud is powered off. A fully charged charging case indicator is white and turns off after disconnecting the charging case. When the earbud battery level is low, you will hear a voice prompt.

Are Mi True Wireless Earphones 2 Basic supplied with a user manual?

Yes, the Mi True Wireless Earphones 2 Basic are supplied with a user manual.

Is it necessary to read the user manual before using the earphones?

Yes, it is necessary to read the user manual carefully before using the earphones to ensure you understand all functions.

How to turn on the earphones?

When the charging case is opened, the earphones will power on automatically. Remember, for the first use, place the earphones in the charging case and close the lid to activate them.

How to connect the earphones to a new device?

Place the earphones in the charging case, press and hold the touch area of one earphone for 3 seconds. The earphone indicator flashes white, and the earphones are waiting for connection. Turn on the device's Bluetooth, then locate and connect to "Mi TW Earphones 2 Basic". If a password is required, enter "0000".

How to answer or end calls using the earphones?

Gently double-tap one of the earphones to answer or end a call.

How to play or pause music using the earphones?

While wearing both earphones, gently double-tap the right (R) earphone to play/pause music. While wearing a single earphone, gently double-tap the earphone to play/pause music.

How to access the voice assistant using the earphones?

While wearing both earphones, gently double-tap the left (L) earphone to access the voice assistant. Please note that the voice assistant function can only be used if your device supports it, and this function requires permission on the device.

How to reset the earphones?

Place both earphones in the charging case. Simultaneously press and hold the touch areas of both earphones for seven seconds, then release the touch areas when the earphone indicators glow white. The earphones have been reset, and the connection history has been cleared. The earphone indicators flash white, and the earphones are waiting for connection.

What is WEEE information and why is it important?

WEEE information concerns waste electrical and electronic equipment. Proper disposal of used batteries and electronic equipment is essential to prevent potential negative impacts on the environment and human health.

Other Resources

Other Xiaomi Manuals:

• Mi True Wireless 2S Earphones User Manual
• Xiaomi Mi True Wireless Earphones Lite User Manual
• MI True Wireless Earphones User Manual

Product Information:

FCC ID: 2ASDITWSEJ08WM

Internal ID: 24662-TWSEJ08WM

HVIN: V7

CAN ICES-3 (B) / NMB-3 (B)

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Xiaomi Inc. is under license. Other trademarks and trade names belong to their respective owners.

Address:

Tianliao Building 1403, Tianliao A Industrial Area, Taoyuan Street, Nanshan District, Shenzhen 518055, China

For more information, please visit our website: www.mi.com