Merlin E148M Four Button Wireless Wall Mount Remote Control

Product Overview

The Merlin Four Button Wireless Wall Mount Remote Control (Model E148M) is designed to operate Merlin garage door openers. It is compatible with both Merlin Security+ and Security+ 2.0 coding systems, offering dual functionality. The remote features four buttons, each of which can be programmed to work with either coding system.

Programming - Merlin Security+ 2.0 Door Opener Systems

The remote is pre-configured for Merlin Security+ 2.0 systems. For EVO door opener models using this code, follow the standard programming procedure:

1. Press and hold the desired button on the remote control.
2. Press and release the 'LEARN' button on your garage door opener.
3. Release the button on the remote control when the opener's light flashes.

Once these steps are completed, the code is learned, and the next press of the programmed remote button should activate the door.

Visual Description: The process involves pressing a button on the remote until its LED indicator flashes continuously, then briefly pressing the 'LEARN' button on the opener. The opener's light will flash or emit two clicks to confirm the code has been learned.

Programming - Merlin Security+ Door Opener Systems

To program the remote for Merlin Security+ systems, follow this unique sequence:

1. Enter programming mode on the remote by pressing and holding both the left and right buttons simultaneously for approximately 5 seconds, or until the remote's LED indicator stays on continuously.
2. Within 30 seconds, press and release the 'LEARN' button on your garage door opener.
3. Select the button on the remote you wish to program and press it once. If the opener's light flashes, the code has been learned. If not, press the same remote button again until the opener's light flashes. Do not press this button further once the code is learned.
4. Press any one of the other three buttons on the remote. This action locks the code into the selected button (from step 3) and turns off the remote's LED.
5. The next press of the programmed button should activate the door. If it does not, repeat the entire process.

Note: To revert a programmed button back to a Security+ 2.0 code, repeat the Security+ 2.0 programming sequence.

Visual Description: The programming involves a specific button combination on the remote to activate its programming mode, followed by interacting with the opener's 'LEARN' button and then confirming the code with another remote button press.

Compatible Merlin Opener Models: This remote can be programmed with various Merlin opener models, including: MR650, MR850, MRC950, MT3850, MT5580P, MT600, MT800, MR60, MR600/800, HE60R, MT1000, CR550, MLR550/750/CR500, ML700/750, MJ3800, MJ3800R, MR1000, MT230, MT60/MT60P.

How to Use the Remote

To operate your garage door, press and hold the desired button on the remote until the door begins to move. The remote typically functions effectively from up to three car lengths away under normal installation conditions. For specific installation queries or range issues, consult an authorized installer.

Remote Control Battery Replacement

The remote is powered by a lithium battery, which is expected to last up to three years. A low battery condition is indicated when the remote control's LED does not flash when a button is pressed. To replace the battery:

1. Use a screwdriver or similar tool to carefully pry open the remote's casing.
2. Remove the old battery. Please dispose of used batteries responsibly.
3. Insert a new CR2032 coin cell battery, ensuring the positive (+) side is facing upwards. Only use CR2032 coin cell batteries for replacement.
4. Replace the remote's cover.

Visual Description: The battery replacement process involves opening the remote casing, swapping the old coin cell battery for a new CR2032, and then closing the casing.

Additional Button Functionality

The additional buttons on the four-button remote can be programmed to control up to three separate devices. This includes additional garage door openers, home lighting systems, gate operators, or access control systems.

Important Safety Warning

⚠️ WARNING: To prevent possible SERIOUS INJURY or DEATH:

• Do not ingest battery. Chemical Burn Hazard.
• This product contains a coin cell battery. If swallowed, it can cause severe internal burns within 2 hours and lead to death.
• Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous.
• Keep new and used batteries away from children.
• If the battery compartment does not close securely, stop using the product and keep it away from children.
• If you suspect batteries may have been swallowed or placed inside any part of the body, seek immediate medical attention.

One Year Limited Warranty

Chamberlain Australia Pty Limited / Chamberlain New Zealand (operating as Merlin) provides this One Year Limited Warranty for the Merlin automatic garage door openers. This warranty covers defects in materials and/or workmanship for a period of one year from the original date of purchase. This warranty is provided in addition to any rights and remedies available under Australian or New Zealand consumer protection laws. Merlin goods come with guarantees that cannot be excluded under the Australian Consumer Law or the New Zealand Consumer Guarantees Act 1993. Consumers are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. Goods are also eligible for repair or replacement if they fail to be of acceptable quality and the failure does not constitute a major failure.