Instruction Manual for Merlin models including: E970M, Four Button Remote Control
Press & hold the button on the remote you wish to use. 2. Press & release the LEARN button on the opener. 3. Release the remote button when the opener light ...
Index of /wp-content/uploads/2021/07
File Info : application/pdf, 2 Pages, 3.15MB
DocumentDocumentThe Merlin Four Button Control can be used with both Merlin Security+ and Security+ 2.0 codes (dual function). 4 buttons are available and any button can be programmed with either code. E970M - Four Button Remote Control LED ROLLER DOOR OPENER LEARN BUTTON DN 1 UP 2 P 3 S LED INDICATOR OR LEARN BUTTON SECTIONAL DOOR OPENER LED INDICATOR LED INDICATOR LEARN BUTTON 3221 SP 1 2 3 LEARN BUTTON Initially: Locate the LEARN button on your particular opener and identify the button on the remote you wish to use. Do not select a button already in use. 1. Programming - Merlin Security+ 2.0 door opener systems The remote is preset for use with Merlin Security+ 2.0 systems, so for EVO door opener models with this code, simply program in the usual manner. Refer to the WIRELESS PROGRAMMING section in your Opener Operating Manual. NOTE: If you are unsure what code has been set previously, use the Security+ programming sequence on page 2. 1. Press & hold the button on the remote you wish to use. 2. Press & release the LEARN button on the opener. 3. Release the remote button when the opener light flashes. The code has been learnt and the next press of the remote button should activate the door. 1 2 Press and hold the button on the remote control you wish to use. The LED indicator on the transmitter flashes continuously. 3 Press and immediately release the Learn button. "clic"kc"lick" The opener light flashes or 2 clicks are heard when it has learnt the code To prevent possible SERIOUS INJURY or DEATH: ·Do not ingest battery, Chemical Burn Hazard. ·This product contains a coin cell battery. If the coin cell battery if swallowed, it can cause severe internal burns in just 2 hours and lead to death. ·Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous ·Keep new and used batteries away from children. ·If the battery compartment does not close securely, stop using the product and keep away from children. ·If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. 2. Programming - Merlin Security+ door opener systems To do this you will need to enter the unique REMOTE PROGRAMMING sequence: 1. Enter the programming MODE on the remote by pressing and holding the left and right buttons simultaneously for around 5 seconds (fig 1). Release when the remote LED stays ON continuously. 2. Press & release the LEARN button on your garage door opener briefly (fig 2). Within 30 seconds, the remote can now be programmed. 3. Select the button on the remote you wish to program and press once (fig 3). If the opener light flashes, the code has been learnt and step 4 can be performed. If not, press the selected button again until the opener light flashes, indicating the code has been learnt. At this point, do not press this button any more. 4. Now press any one of the OTHER 3 buttons of the remote (fig 4). This LOCKS IN the code to the button selected in step 3 and the remote LED turns OFF. 5. The next press of the button should activate the door, if not repeat the process. NOTE: In the event you need to return a button to Security+ 2.0 code, repeat the programming sequence outlined above. 1 2 professional O 180 s 60 s 120 s 1 2 3 open 3 4 open force operate learn delete MR650,MR850 MRC950 MT3850 MT5580P HOW TO USE THE REMOTE Press and hold the button down until the garage door starts to move. The remote will operate from up to 3 car lengths away on typical installations. Installations and conditions vary, contact an installing dealer for more information. MT600,MT800 MT1000 MR60, MR600 MR800 MT60/MT60P MJ3800, MJ3800R MR1000 MT230 4-BUTTON REMOTES Additional buttons on the remote can be programmed to operate up to 3 devices such as additional garage door openers, light controls, gate operators or access control systems. THE REMOTE CONTROL BATTERY The lithium battery should produce power for up to 3 years. If the battery is low, the remote control's LED will not flash when the button is pressed. To replace battery : Use a screwdriver to open the case as shown Remove the old battery. Dispose of old batteries properly. Insert replacement batteries positive side up. Replace the batteries with only CR2032 coin cell batteries. Replace cover. CR2032 114A5471A ONE YEAR LIMITED WARRANTY Chamberlain Australia Pty Limited / Chamberlain NewZealand (Chamberlain), the manufacturer of Merlin®automac garage door openers, warrants to the original consumer purchaser of this product that it is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase. Chamberlain is commied to manufacturing and supplying high quality goods. As part of this commitment, we seek to provide reliable service and support for our goods and are pleased to provide you, the original purchaser, with this Chamberlain Limited Warranty. The benefits given to you under this Chamberlain Limited Warranty are in addion to any rights and remedies that you may have under Australian or New Zealand consumer protecon laws. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law, or New Zealand Consumer Guarantees Act 1993. You are entled to a replacement or refund for a major failure and for compensaon for any other reasonably foreseeable loss or damage. You are also entled to have for compensaon for any other reasonably foreseeable loss or damage. You are also entled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.Adobe PDF library 15.00 Adobe Illustrator 24.1 (Windows)