RCB R10X Electric Scooter User Manual

How to Contact RCB on Amazon

Step 1: Log in to your Amazon account.

Step 2: Go to Your Orders. Select Problem with order in the list.

Step 3: Click the "Ask a Question" button. Choose your topic from the list displayed.

Step 4: Select Contact seller.

*If you purchased RCB products by other platforms or channels, please also find the corresponding seller contact support. Thanks for your support and patience!

Table of Contents

1. Packing List
2. Product Structure
3. Product Parameters
4. Assembly Instruction
5. Function Description
6. Error Code Indication
7. Folding Operation
8. Safty Instructions
9. Safety Reminder
10. Daily Care And Maintenance

1. Packing List

Description of items included in the package:

• M3 Hexagon Wrench x1
• Charger x1
• M5 Screw x4
• User Manual x1

After receiving the electric scooter, please check the package carefully. If anything is missing or damaged, please contact customer service as soon as possible.

2. Product Structure

Diagram showing the parts of the RCB R10X Electric Scooter:

• (1) Meter
• (2) Throttle Dial
• (3) Right Brake Lever
• (4) Left Brake Lever (with bell type)
• (5) Handlebar
• (6) Headlight
• (7) Folding Large Stem
• (8) Head Tilt Stem
• (9) Suspension Fork
• (10) Front wheel
• (11) Foot Pad
• (12) Kick Stand
• (13) Frame Chassis
• (14) Rear Fender (hook type)
• (15) Taillight
• (16) Disc Brake
• (17) Back fork
• (18) Motor Wheel

3. Product Parameters

*Fully charged, 75kg load, 30 ℃, 70% humidity, level 3 wind speed, flat road, and measured at a constant speed of 12mph, the actual battery life will vary from factors such as load, temperature, wind speed, road surface and operating habits.

*All the above data are from RCB laboratory, and errors may occur due to changes in objective conditions during actual use.

4. Assembly Instruction

1. Raise the riser to make it stand up (see image 1), lock the folding wrench (see image 2), and loosen the kick stand (see image 3).
2. Install the handlebar on the stem (see image 4), and tighten the four M5 screws by the M3 Hexagon Wrench (see image 5).

5. Function Description

1. Charge your scooter

Please make sure that the scooter has sufficient power before each use. The scooter is fully charged when the LED on the charger changes from red to green.

2. Start

• (1) Long press the power button for 2 seconds: power on and meter lights.
• (2) Click the power button one time (short press): Switch the gear.
• (3) Double click the power button continuously (short press): the front and rear lights are on.
• (4) Click the power button continuously four times (short press): enable cruise control.
• (5) Click the power button continuously five times (short press): Switch between zero start and non-zero start mode.
• (6) Click the power button continuously six times (short press): Switch between TRIP and ODO.
• (7) Long press the power button for 2 seconds: Power off, automatic shutdown after 10 minutes of inactivity.

3. Meter

The meter displays information such as Light, Speed, TRIP, ODO, and Mileage. It also indicates the current mode: Sport Mode, Standard Mode, Deceleration mode, and Energy-Saving Mode.

4. How to ride

Warning: Wear a helmet, elbow pads, and knee pads. Please read the instructions carefully before using. Do not touch the brake system. Refer to the instructions for more information.

1. Turn on the scooter and check the power indicator.
2. Step on the deck with one foot, and slowly kick off the other on the ground. When the scooter starts to coast, put both feet on the deck and press the accelerator.
3. When the scooter is at a full stop, the accelerator automatically turns off. To restart the scooter, it is necessary to repeat step 2.